Samsung Defrost Thermistor Parts

• Takes too long to dry
• Doesn't shut off

You can do this! Although an Art Director by trade, I like working with my hands. I’m adept at working with tools and following instructions. In today’s disposable society, I prefer fixing things. That said, this has to be the easiest repair I’ve ever attempted with the largest cost-savings versus hiring a professional. My brand new dryer had been in use fewer than six months (average 6 loads per week) when suddenly the dryer would not heat. The drum would spin, there were no error codes, and... Read more

• Won't start

You can do this! Although an Art Director by trade, I like working with my hands. I’m adept at working with tools and following instructions. In today’s disposable society, I prefer fixing things. That said, this has to be the easiest repair I’ve ever attempted with the largest cost-savings versus hiring a professional. My brand new dryer had been in use fewer than six months (average 6 loads per week) when suddenly the dryer would not heat. The drum would spin, there were no error codes, and... Read more

• Shuts off too soon
• No heat or not enough heat
• Takes too long to dry

I used Fixya as an initial source describing my problem. I got two responses which were very helpful. One that the "coils" were probably the problem. Two, that the problem could be the thermostat or a thermistor in the dryer. I verified that AC was coming from the timing control, that both the two terminal and three terminal coils,the igniter and shut off thermostat all had continuity. I then applied AC directly to the coils: the two terminal coil ""clanked" and I interpreted that as the coil... Read more

• Fridge too warm
• Frost buildup
• Doesn't shut off

Poped off plastics caseing inside the frigerator. Unscrewed 4 screws holding black fan inplace. Followed yellow wire to locate white sensor. Need to be careful not to break styrofoam, don't force it, it should seporate from plastic easy as long as the 4 screws are out. Swap it for the new one and button it back up. While I was in there I replaced the defrost sensor and the other sensor next to the heating rod. Also I know there is an issue with drain hole plugging up with ice so I extended the... Read more

You can do this! Although an Art Director by trade, I like working with my hands. I’m adept at working with tools and following instructions. In today’s disposable society, I prefer fixing things. That said, this has to be the easiest repair I’ve ever attempted with the largest cost-savings versus hiring a professional. My brand new dryer had been in use fewer than six months (average 6 loads per week) when suddenly the dryer would not heat. The drum would spin, there were no error codes, and... Read more

Replaced heating element and thermostat, took me about 2 hours but that's because i had to vacuum out the dryer inside and I also checked the fan before I closed the dryer back up. I have a Samsung DV448AAEP. Works great and saved my family money! Read more

• Takes too long to dry
• Doesn't shut off

I researched the issue on You tube and found out it could be either the "belt broke switch" or the Moisture sensor. A friend who was an appliance mechanic advised "since you have to take it all apart anyways, its best to replace the belt, spring, and Idler wheel" I bought the 5 item for $52. I watched the video on the AppliancePartsPros for changing out the belt and I replace all items on the list. Took 1 1/2 hrs and was fixed on restart!! * Wear gloves, the sheet metal is very sharp edges!* Read more

• Frost buildup

Replaced sensors and heater element. We'll see if that fixes the problem. It usually happens every 3 months. Read more

Sensor near coils replaced did not need anything else. Read more

Turn off the water to the ice maker. Unload the freezer and remove the freezer door so you have room to work. Remove the ice maker by removing 2 screws in the front then pull the unit toward the front and unplug the wiring connection. The pipe will now be exposed. Remove the flexible piece from the front of the pipe that directs the water flow to the ice cube tray. Remove the wire tie on the front of the pipe and peel off the insulation surrounding the pipe. The heater will now be exposed.... Read more

When starting my dryer the motor would power up and rotoe the drum and blower. Afetr about 20-30 seconds the igniter would come on then the gas valve would open and I would get heat for about 6 or 7 seconds then it would shut off. I know the burner is suppoed to cycle on and off but once the burner shut off it would not come bqack on unless I shut the dryer off and then back on. I checked for continuity on the thermistor, the thermal fuse and the high temp sensor. All three of them appeared to... Read more

I found freezer thermal link was open and not closing when cold. Replacement fixed problem. Read more

Samsung refrrigerator. it started when the setting was on cubes but was putting out crushed ice. then months later the water refill was running down into the ice bucket causing a massive block of ice in the bucket. look closely at the first two or three cubes in the ice tray after they unload. mine were not dumping and staying in the tray. when the water refill kicked on it would overfill the tray (because of the leftover cubes remaining in the tray) and would run down into the ice bucket... Read more

I replaced the temperature sensor, the thermo fuse, and the heating element that thaws the evaporator on a cycle to keep the evaporator from freezing up. The most time consuming part of the repair was waiting for the fridge to thaw out so that I could remove the cover. I disconnected the fridge the night before and placed a fan on low with the doors open so that it was thawed out when I awoke. It was easy to remove the evaporator cover once I removed all of the shelves. I took pics as i was... Read more

• Frost buildup
• Doesn't shut off

Ordered parts, defrosted refrigerator, and replaced with new items. This problem has been going on quite some time, while Samsung refused to acknowledge the defective unit, claiming it was owner fault. The defrosting had to be completed every 3-4 months and managed in time to require defrosting every few days. Originally a repairman came and although he defrosted it the first time, he informed us, this is quite common and the unit is defective by design; which is why we continued to defrost on... Read more

Knowing from a previous repair, that there was only 3 parts that could be bad. I decided if I was going to take it apart to change all 3. Not having the proper test equipment, it was cheaper to replace the 3 parts than pay a repair person. Read more