Hardware Hand Snowblower Gearbox Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: 3360629
Fix a washer that won't spin or agitate with a new transmission. Common symptoms include loud clunking noises or clothes staying wet after cycles.
Do-It-Yourself Stories from Customers like You
Washer not spinning end of cycle Jeff C. • Morrisonville , NY • November 21, 2014
Using appliancepartspros.com site took washer apart to diagnose bad clutch. The clutch was bad but once inside I noticed grease everywhere and after a quick online chat with rep. determined gear case was leaking and needed replacement. Replaced clutch & gear case. Followed video tutorial and took a little more than 30 minutes start to finish for me - I have no experience. The most difficult part for me was actually just getting the retainer ring (little wire) to secure clutch in place-took...
Read more
More
$327.95
- Compare At:
-
$386.98
- You Save:
-
$59.03
Genuine Whirlpool part
By: Whirlpool
Part Number: 882699
Replace your trash compactor's broken or stripped drive gear assembly. Includes gears, shafts, and components that transfer motor power to the ram mechanism.
This part fixes the following symptoms
-
Compactor ram gets stuck
-
Noisy
See more...
Do-It-Yourself Stories from Customers like You
Fractured drive gear Keith S. • Warrenton , VA • February 09, 2016
The compactor failed with the ram down, so the drawer wouldn't open which in turn made the mounting brackets inaccessible. This necessitated sliding a thin oscillating saw blade between the cabinet face frame and the counter top to cut through the brackets. It was then possible to roll the unit out and place it on its side. I removed the five screws holding the bottom pan in place, dropped the pan exposing the gear/chain train. The large gear was cracked from shaft out to the edge. One of...
Read more
More
$77.76
- Compare At:
-
$91.76
- You Save:
-
$14.00
Genuine Ge part
By: Ge
Part Number: WB1X1293
Secures the igniter to the burner assembly in gas ranges and ovens. Replace if stripped, missing, or damaged during igniter replacement or repair.
Do-It-Yourself Stories from Customers like You
Failure to hold temperature after preheating. Michael D. • Wilmington , DE • January 07, 2023
I was getting really frustrated with our oven. It would preheat to the correct temperature, then slowly lose heat until it was down to about 200 degrees. So it took about two hours to heat a pizza!
Finally decided to repair the oven myself, rather than pay $300.00 to have a repair person come out. Ordered the replacement igniter from AppliancePartsPros.com, and it arrived in two days.
I followed the instructional video on the AppliancePartsPros.com website, and it was going well until I...
Read more
More
$11.34
- Compare At:
-
$13.38
- You Save:
-
$2.04
Genuine Frigidaire part
By: Frigidaire
Part Number: 316240600
Secures the ignitor assembly to your gas cooktop burner base. Replace if screw head is stripped, threads damaged, or screw is missing after disassembly.
Do-It-Yourself Stories from Customers like You
Slow to ignite Matthew F. • East Peoria , IL • October 07, 2019
It took a little longer then I was hoping but wasn’t terrible. If the burner is very old at all make sure to get the new screws. Both of mine snapped when trying to remove them. The new one works great.
Read more
More
$16.75
- Compare At:
-
$19.77
- You Save:
-
$3.02
Genuine Whirlpool part
By: Whirlpool
Part Number: 388253A
The Neutral Drain Kit is an OEM part for Whirlpool washing machines. This kit facilitates the neutral drain function, which allows the washer to drain water without spinning the tub, ensuring efficient water removal before the spin cycle begins.
Causes of a bad neutral drain kit can include wear and tear over time, mechanical failure of the components, or damage due to improper installation or handling. A faulty neutral drain kit can lead to draining issues, affecting the overall performance of the washing machine.
Symptoms of a bad neutral drain kit include:
- Washer not draining properly
- Extended or incomplete drain cycles
- Water remaining in the tub after the drain cycle
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Teeth stripped from gear in transmission Robert G. • Wentzville , MO • June 17, 2015
The parts I purchased from Appliance Parts Pro fit perfectly and were reasonably priced. I received them the next day, which made the Wife (and me) very happy. Although Appliance Parts Pro did not have a repair video for this, I was able to find one online and the machine is washing like new again. The website is well laid out and easy to find what your looking for. Between the available parts and the videos they provide, anyone who is reasonably handy should be able to repair their machine as...
Read more
More
$51.62
- Compare At:
-
$61.43
- You Save:
-
$9.81
Genuine Frigidaire part
By: Frigidaire
Part Number: 316540900
The Screw is an OEM part for Frigidaire ranges and cooktops. This part secures the burner head in place, ensuring proper alignment and functioning of the burner.
Causes of a bad burner head screw can include loosening due to repeated heating and cooling cycles, damage from impact or mishandling, or simply wear and tear over time.
Symptoms of a loose or missing burner head screw include:
- Uneven or irregular flame pattern on the burner
- Burner head not sitting flush or properly aligned
- Burner head wobbling or moving during use
- Potential gas leaks if the burner head is not securely fastened
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Ignitor failed / screw that attached burner to ignitor stripped Michael M. • Roundhill , VA • May 17, 2015
Ordered new Ignitor / Orifice and screws
Mike was a great resource, he helped me thru the project.
Read more
More
$19.95
- Compare At:
-
$23.74
- You Save:
-
$3.79
Genuine Whirlpool part
By: Whirlpool
Part Number: W10491985
The Range Screw is an OEM part for Whirlpool ranges. It is a small but essential component used to secure various parts and panels of the range. It is designed to fit securely into pre-drilled holes, holding components tightly in place.
There are a few factors that can lead to a bad Range Screw. Over time, screws may become loose or stripped due to frequent use or inadequate tightening. Accidental cross-threading or overtightening can also damage the screw or the surrounding components.
Symptoms of a bad screw may include loose or wobbly parts, rattling noises during operation, or difficulty in keeping components securely attached. This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
Do-It-Yourself Stories from Customers like You
Oven door outer glass was broken Slydell B. • Cape Coral , FL • November 26, 2014
Using the parts I ordered, I replaced the glass myself following the very helpful video on your web site.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Frigidaire part
By: Frigidaire
Part Number: 316001013
Size: 10-24 x 1.375 inch.
Do-It-Yourself Stories from Customers like You
Replaced screws on oven handle and door Jason D. • Bowling Green , KY • February 14, 2016
Secured the inner and outer door together and screwed handle back in place.
Read more
More
$6.41
- Compare At:
-
$8.02
- You Save:
-
$1.61
Genuine Samsung part
By: Samsung
Part Number: DE60-20066A
Secures your microwave to kitchen cabinets during installation. Replace missing, stripped, or damaged bolts for safe and stable mounting.
Do-It-Yourself Stories from Customers like You
Removed 1 year old microwave to paint kitchen internal thread assembly stripped Joel L. • North Richland Hills , TX • December 01, 2016
I took the machine screws out of the outer panel for the right side only. Then pull the panel back a bit to release the lips from the front of the machine and had immediate access to the internal assembly that housed mounting nut.
Order the new parts from AppliancePartsPro.com during the Thanksgiving week. Still received via FedEx in short time due to their same day shipping - which was greatly appreciated and surprising. Most small part places take a while to get the product out the door,...
Read more
More
$30.54
- Compare At:
-
$36.34
- You Save:
-
$5.80
Genuine Whirlpool part
By: Whirlpool
Part Number: W10777162
The Screw is an OEM part for Whirlpool ranges. This screw is used to secure various components within the range, ensuring that parts such as panels, control boards, or burners are firmly attached and remain stable during operation.
Causes of a bad range screw can include regular wear and tear, over-tightening, or exposure to high heat.
Symptoms of a bad range screw include:
- Loose or unstable components within the range
- Difficulty in securing parts during maintenance or repair
- Visible damage or wear on the screw
- Parts becoming misaligned or rattling during operation
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Left door hinge would not allow door to close square to opening Jay R. • Clearwater , FL • October 19, 2019
Replaced the hinge receiver with a new one. The old one was bent slightly inside where it could not be seen. I think someone pushed the door down to far or fell on it. 2 screws to remove it, take out storage drawer and reach up little ways to remove and replace the receiver. Replace the 2 screws. The receiver comes with 2 screws but I ordered an extra ( never used it ). The sides of the receiver were spread just a tiny bit but were enough to cause a problem.
Read more
More
$7.48
- Compare At:
-
$8.90
- You Save:
-
$1.42
Genuine Whirlpool part
By: Whirlpool
Part Number: WP74006515
The Oven Door Panel Screw is an OEM replacement part for Whirlpool ovens and ranges. It is a component used to fasten the outer panel to the interior metal door frame.
Causes of a bad oven door panel screw can include normal wear from repeated opening and closing of the door, damage such as stripped threads from overtightening, or corrosion over time inhibiting its fastening function.
Symptoms of a bad oven door panel screw include:
- The outer panel becoming loose, wobbly, or detached
- Gaps appearing around the door seam
- Scratches or other damage to the door panel
- Reduced insulation quality of the door assembly
This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Door handle of upper oven broke off Jodi G. • Oak Park , MI • December 01, 2014
Start by removing the frame on the sides and bottom of the door. (Do not unscrew the corner screw holding the side frame and bottom together.) Be careful the glass will fall once the last screw is removed from the bottom so hold tight. Carefully remove glass and set aside. Remove top frame that held the handle. Once all the frame work and outer glass is removed unscrew the bracket that held the door handle from the door. Taking the top frame and bracket insert screw and washer and screw the...
Read more
More
$7.48
- Compare At:
-
$8.90
- You Save:
-
$1.42
Genuine Frigidaire part
By: Frigidaire
Part Number: 316278700
Mounting screw for range oven door handles. Secures the handle to the door panel. Replace when stripped, corroded, missing, or if handle is loose.
Do-It-Yourself Stories from Customers like You
The door handle screw holes were hollowed out (the handle is plastic) making the door continuously fall off the plastic latches on the door trim were also broken off. Matthew F. • Columbia , MO • January 17, 2020
Replacing the trim takes a little bit of alignment and light force. The trim slides over the glass panel of the door, with the glass sliding into plastic tabs. We kept the door nearly vertical (almost closed), lined up the tabs on the trim with the glass door, and used mild force to slide the trim down onto the glass door. (Also, we found that the tabs on trim we ordered were much bigger than the tabs on our broken trim. This is probably due to slight variations in Frigidaire's design over...
Read more
More
$10.95
- Compare At:
-
$13.14
- You Save:
-
$2.19
Genuine Whirlpool part
By: Whirlpool
Part Number: W10821385
Includes brackets, screws, and fasteners for secure microwave installation. Replace missing, lost, or incomplete hardware from floor models or clearance units.
Do-It-Yourself Stories from Customers like You
Floor model missing parts. Michael S. • Olathe , KS • September 30, 2017
I ordered the mounting bracket, mounting hardware and template for the top cabinet. Everything I ordered was an exact fit. Install only took about 30 minutes after running the new electrical for the microwave. Appliance parts helped me save almost $400.
Read more
More
$75.95
- Compare At:
-
$91.14
- You Save:
-
$15.19
Genuine Whirlpool part
By: Whirlpool
Part Number: 8205948
For mounting also consider WPW10269225 mounting plate
Do-It-Yourself Stories from Customers like You
We needed an assembly kit and turntable for wmh32517as 1 Jewell L. • Cincinnati , OH • March 01, 2015
We found the parts on this website. Thanks to your search bar, we could see if the parts would work on our model microwave.
Read more
More
$18.23
- Compare At:
-
$21.69
- You Save:
-
$3.46
Genuine Frigidaire part
By: Frigidaire
Part Number: 5304453707
This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.
- Fastens metal or plastic parts to the cabinet/frame
- Helps maintain alignment and reduce vibration or rattling
- Direct replacement for lost, damaged, or rusted hardware
- Keeps covers and brackets safely in place
What's included: 1 screw Install notes:
- Disconnect power before servicing; for gas appliances, also shut off gas supply
- Match one-for-one with the original screw; verify length/type before installation
- Start threads by hand to avoid cross-threading; tighten snugly without overtightening
- Use the correct driver bit to prevent stripping the screw head
Do-It-Yourself Stories from Customers like You
Ice dispenser not working auger not turning Roger H. • Chesapeake , VA • August 21, 2016
Replace dispenser micro switch. Also replaced broken faceplate and rusty screws. Appliance parts Pro YouTube video was helpful in diagnosis and disassembly. Parts arrived quickly.
Read more
More
$23.61
- Compare At:
-
$27.86
- You Save:
-
$4.25
Genuine Frigidaire part
By: Frigidaire
Part Number: 5304507924
Mounting screw for electric and gas ranges. Secures panels, brackets, and internal components. Replace if screw is stripped, missing, or broken.
More
$5.35
- Compare At:
-
$6.42
- You Save:
-
$1.07