We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
If your oven won't reach the right temperature or shows an F9 error, the temperature sensor may be faulty. Simple DIY repair in under 45 minutes.
Searched the internet and found that the culprit could be 3 different parts. Ordered them and fixed the issue by replacing the thermostat! Read more
Replacement window glass for range oven doors. Restores clear viewing area when original glass is cracked, chipped, cloudy, or shattered. Installs inside door.
It would not be fixed if not for Appliance Pro. I ordered the glass to replace and it arrived the next day. Removed old glass and put in the new. Easy! Thank you Appliace Pro!! I have already recommended you to others. Read more
Fix F9 error code or oven not heating issues. This thermal safety thermostat monitors temperature to prevent overheating. DIY repair in 15-60 minutes.
Looked online. Others said to start with the thermostat because its cheap and easy to fix, so I did. The thermostat is located at the rear of the oven on the back. You need to remove a total of 3 panels to get to it. Do not confuse it with the thermal sensor at the rear of the oven on top. My thermostat was clearly deformed, and I had never run a self clean like other with testify to. Simply replace it - easy. Oven worked like new. Read more
If your range control panel is loose or cooking functions are erratic, the PCB supporter may be cracked. This mounting bracket secures the circuit board.
Removed front panel, disconnected the wires- marking each plug so it would go back correctly. Removed the control housing, and replaced the parts. Reassembled. You guys are absolutely great. Read more
Fix an unresponsive oven control knob or broken control dial. This encoder board detects knob position and sends signals to adjust temperature settings.
Replaced the cheap plastic lever supporter with another LG OEM cheap plastic lever supporter. I should have bought two as I can see this problem happening again. Job was a simple fix and only required a Phillips head screwdriver. I did not need to remove any connections as there was enough room and wire to pull out the oven control assembly and make the repair. One word of caution is to be careful as the sheet metal internal cover and bottom of the control knob panel is razor... Read more
Fix an oven door that won't stay open or slams shut with this range door spring. Simple DIY repair requiring only a Phillips screwdriver, 30 minutes.
This is the motor housing or support bracket that holds the convection fan motor in place inside the oven. It secures the motor and ensures proper airflow for even cooking during convection baking. Replace this housing if it is cracked, warped from heat exposure, or if the convection fan vibrates excessively or sits loosely.
Fix unresponsive control panel buttons with this tactile switch replacement. Restores reliable button response. Simple DIY repair, typically under 5 minutes.
Tested switch with a jumper. Confirmed the switch was bad. Ordered new switch, less than a minute installation.good to go Read more
Plastic supporter stem that fits between the control knob and encoder board on your range. Replace if broken, cracked, or jamming the control switch.
I took off the front control panel with a Phillips screwdriver. I used a mirror to locate some of the screws under the panel. Being handy and common sense helped a lot. I am very experienced with fixing stuff but will admit that i did get a bit frustrated. A second set of hands was helpful but not necessary. I took off the shroud that goes around the knob and that was a mistake. It was difficult to put back on and was not required to fix the problem. TAKE PHOTOS AS YOU PROGRESS and don’t lose... Read more
Replace your burned-out microwave cooktop light to restore bright illumination under your over-the-range unit. Confirm fit by model number before ordering.
Purchased light bulb and installed. I had experienced difficulty locating the light bulb I needed, I was lucky to find Appliance Parts on line, and they had just what I needed. I will definitely shop with Appliance Parts in the future, for any and all needed replacement parts. Thank You Read more
Oven not heating or cooking unevenly? This heating element generates the heat needed to cook food. Common fix for temperature issues in electric ovens.
The Supporter is an OEM part for LG wall ovens. This part offers stability and support to the temperature control knob. This shaft is a pivotal component that connects the control knob to the internal temperature control mechanisms, ensuring precise adjustments to the oven's heating settings.
Over time, the Supporter can wear out or become damaged due to frequent use, accidental impacts, or general wear and tear.
Symptoms of a bad Supporter include:
This OEM LG part is also compatible with some Kenmore models.
Oven won't heat, turns off randomly, or completely dead? This power control board manages heating elements and oven functions. Moderate difficulty repair.
This is a sheath-style heating element mounted at the top of the oven cavity that provides high, direct heat for broiling. It glows red when functioning properly and is responsible for searing and browning food from above. Replace this element if it no longer heats up, heats unevenly, has visible cracks or blistering, or if the broil function stops working entirely.
This thermostat is a temperature-sensitive safety switch used in LG microwaves. It monitors internal temperature and opens the circuit when overheating is detected to help protect components from heat damage.
Fix inaccurate oven temperatures with this range temperature sensor. Restores proper heating cycles when your oven runs too hot or cold.