Lg Thermistor Parts

• No heat or not enough heat
• Won't start

Checked and cleaned vent which was in need of cleaning, but not too bad (I do not consider this a primary causal detail, but can be a problem, so clean yours). Replaced Hi-Limit Thermostat (safety thermostat) after confirming the circuit was open with ohm meter. While I was in there, I completely cleaned the heater and ducting and internal workings of the dryer. Confirmed the heater coils were good via 20ohm, 20ohm, 40ohm readings (LG service manual has wrong readings). Two weeks later, same... Read more

• Takes too long to dry

After I cleaned out the typical 1.5 pounds of lint from the vent, ( I do it every 2 months), I went searching for a solution. I found 6 possible causes on this site and purchased everything except a new burner; I wasn't going to go that far. Let the fun begin. Since my vacuum was still nearby, I thought I was ready for anything. Wrong. After I watched all the videos again for reassurance, I went in with screwdriver in hand and laptop nearby. I removed the top and looked inside. Don't be fooled,... Read more

Checked and cleaned vent which was in need of cleaning, but not too bad (I do not consider this a primary causal detail, but can be a problem, so clean yours). Replaced Hi-Limit Thermostat (safety thermostat) after confirming the circuit was open with ohm meter. While I was in there, I completely cleaned the heater and ducting and internal workings of the dryer. Confirmed the heater coils were good via 20ohm, 20ohm, 40ohm readings (LG service manual has wrong readings). Two weeks later, same... Read more

I watched the Appliance Parts Pro video and saw that it was a job that I could easily do. I ordered the Rotor Position sensor switch for about $21 on a Monday and it was delivered by UPS on Wednesday. The process was straight forward: 1) remove the back cover from the washing machine (4 screws), 2) remove the main bolt holding the magnetic drum on the motor; 3) remove the 6 bolts holding the coil on the motor; 4) remove the ground screw and wire harness clamp screw; 5) take the old sensor... Read more

Checked and cleaned vent which was in need of cleaning, but not too bad (I do not consider this a primary causal detail, but can be a problem, so clean yours). Replaced Hi-Limit Thermostat (safety thermostat) after confirming the circuit was open with ohm meter. While I was in there, I completely cleaned the heater and ducting and internal workings of the dryer. Confirmed the heater coils were good via 20ohm, 20ohm, 40ohm readings (LG service manual has wrong readings). Two weeks later, same... Read more

Checked and cleaned vent which was in need of cleaning, but not too bad (I do not consider this a primary causal detail, but can be a problem, so clean yours). Replaced Hi-Limit Thermostat (safety thermostat) after confirming the circuit was open with ohm meter. While I was in there, I completely cleaned the heater and ducting and internal workings of the dryer. Confirmed the heater coils were good via 20ohm, 20ohm, 40ohm readings (LG service manual has wrong readings). Two weeks later, same... Read more

After I cleaned out the typical 1.5 pounds of lint from the vent, ( I do it every 2 months), I went searching for a solution. I found 6 possible causes on this site and purchased everything except a new burner; I wasn't going to go that far. Let the fun begin. Since my vacuum was still nearby, I thought I was ready for anything. Wrong. After I watched all the videos again for reassurance, I went in with screwdriver in hand and laptop nearby. I removed the top and looked inside. Don't be fooled,... Read more

• Fridge too cold
• Fridge too warm

I replaced the evaporator sensor. Your company sent me the exact sensor I needed at a great price. No other company was able to help. No call was needed. Your website was great. Read more

Replaced defrost sensor in freezer compartment, if you are handy this is a do it yourself job. The cover in the freezer section just pops out not tools needed. You will need a few small zip ties and some cutters to remove the old zip ties. Take a picture were the old sensor was before removing and reinstall in the same place. I used a meter to check continuity of the defrost element and found the element to be ok. I was quoted $85 to have someone come to the house just to check the unit and... Read more

Replaced thermistor Read more

• Frost buildup
• Doesn't shut off
• Fridge too warm

I removed the defrost sensor assembly, installed a new one, it worked. Because of a shipping problem with FEDEX, Appliancepartspros resent the parts not once but twice. Needless to say, they are my go-to source for parts from now on. Read more

I was having trouble with my Kenmore Front Load washer. It wouldn't finish the wash cycle...it kept displaying an LE Error code. After I went to Google to help diagnose the problem, which was a bad RPS Sensor, I ordered the part from AppliancePartsPros.com. It literally took about 15-20 mins and with the help of my son-in-law, my washing machine was fixed!! It was going to cost me $85.00 for the Sears repairman to walk in my door, not including parts and labor, and I only paid $27.00... Read more

Used video and took apart dru, this was extremely helpful. I bypassed the belt and door switch. Tested gas valves (gas disconnected) with multimeter. Found that the igniter worked the first gas valve, but the second gas valve would not open and the igniter would stay on. Found a flow chart online that shows the flame detect turns on causing the gas to turn on and shuts off the igniter. I replaced it and tested again. Igniter turns on, shuts off, then power to the second gas valve turns... Read more

I removed the defrost sensor assembly, installed a new one, it worked. Because of a shipping problem with FEDEX, Appliancepartspros resent the parts not once but twice. Needless to say, they are my go-to source for parts from now on. Read more