Parts for Lg MVH1615WW / CWHEGSE: Section 1 Parts

A Tap-Tite binding-head screw used to fasten appliance panels and components where a self-tapping metal thread is required. Replaces missing or damaged fasteners to restore secure assembly and reduce vibration or rattling. What it does:

• Creates its own mating thread in thin sheet metal for a secure hold without a nut.
• Holds panels, brackets, and trim in place to prevent looseness or movement.
• Commonly used where stripped, missing, or broken screws cause rattling, misalignment, or parts that won't stay attached.
• Compatible with standard screwdrivers or nut drivers sized to the binding-head.

• Disconnect power and unplug the appliance before working on it.
• Use the correct driver bit to avoid cam-out or head damage.
• Start straight and apply steady pressure; avoid overtightening to prevent stripping the formed threads.
• If the original hole is badly damaged, assess for repair or use of a larger fastener as needed.

This truss head tapping screw secures panels, brackets, and covers in your appliance. Replacing a missing or damaged fastener restores a snug fit, reduces vibration, and helps keep components properly aligned for reliable performance.

• Provides low-profile holding power; wide truss head helps secure thin panels and trim
• Replaces lost, stripped, or corroded screws at the original mounting points
• Helps eliminate rattling, vibration, or loose handles/covers
• Addresses situations where a screw will not tighten or backs out during use

• Disconnect power; shut off water/gas if applicable before servicing
• Align parts and hand-start threads to avoid cross-threading
• Tighten until snug; do not overtighten to prevent stripping
• If the receiving hole is damaged, for repair before installing the new screw

This is the inner door frame assembly for a microwave oven. It provides the structural support for the door's window, trim, handle, and latch so the door aligns and closes properly and the interlock switches engage.

• Forms the inner structure of the microwave door and supports the window/screen, trim, and latch components
• Helps maintain alignment so the door closes and latches securely
• Replace if cracked, warped, or if mounting tabs are broken
• Typical symptoms include a door that won't close or stay shut, "door" error messages, the unit not starting unless the door is pressed, or a loose/rattling door panel

• Disconnect power before servicing; if over-the-range, support or remove the microwave before working on the door
• Use gloves/eye protection and watch for sharp edges
• Photograph door stack-up; transfer existing glass, handle, choke/trim, hinges, and screws to the new frame
• After reassembly, ensure the door closes squarely and that interlock switches engage before restoring power

Inner plastic door film covers the holes in the inner door frame.

The Choke Cover is an OEM part for LG microwaves. This is a protective shield that covers the microwave’s internal components, preventing interference and ensuring the safe operation of the microwave.  

Causes of a bad choke cover can include physical damage from accidental impacts, deterioration due to prolonged use, or exposure to high temperatures.

Symptoms of a bad choke cover include:

• Unusual noises during microwave operation
• Visible cracks or damage to the cover
• Microwave not heating food properly
• Sparks or arcing inside the microwave

This OEM LG part is also compatible with some Kenmore models.

This door latch assembly for a microwave engages the door hooks and actuates the interlock switches so the unit recognizes a closed door, restoring proper latching and helping ensure the oven only operates when securely shut.

• Engages the door hooks to trigger the interlock switches and signal "door closed"
• Can help resolve no-start or "Door/Open-Close" indications with the door shut
• Addresses a door that won't latch, feels loose, or shows cracked/worn latch parts
• Built to mount in the original location and interface with existing door switches

• Disconnect power before service; microwaves contain high-voltage components that can retain a dangerous charge
• Access typically requires removing the control panel to reach the latch/interlock bracket
• Note switch orientation and spring positions; transfer any reusable hardware from the old assembly
• After installation, verify firm door engagement and proper interlock switch actuation before restoring power

The Door Latch Spring is a genuine OEM part for LG microwaves. As a key component of the microwave, the door latch spring is responsible for providing the tension needed to securely close and latch the microwave door. It works behind the scenes to ensure a tight seal when the door is shut.

Symptoms of a bad door latch spring include:

• The microwave door not closing or latching properly 
• Gaps appearing around the door seal when shut
• Difficulty opening and closing the door

Causes of a bad door latch spring can include wear and tear over time. Exposure to excessive door slamming can also place undue stress on the spring.

This genuine LG OEM  replacement part is also compatible with Sears/Kenmore microwaves.

Color: White