Parts for Lg WD-3243RHD / AOWEEUS: Section 4 Parts

This Thermostat Assembly monitors and regulates internal temperature within the appliance's heating circuit. Replacing a failed thermostat restores proper heat control, helps prevent overheating, and can resolve common heating performance issues so cycles run correctly. What it does

• Senses internal temperature and opens/closes the heater circuit to maintain proper heat
• Provides over-temperature protection by cutting power at unsafe temperatures
• Helps ensure consistent heating performance throughout the cycle
• Helps with symptoms such as no heat, overheating/shutting off, or unusually long cycle times

• 1 thermostat assembly

• Disconnect power before servicing; allow hot components to cool
• Access the thermostat location (varies by model); note wire positions before removal
• Mount flush to the surface for accurate sensing; transfer original hardware if required
• After installation, test operation; use a multimeter for continuity checks if needed

This heater assembly warms the wash water inside the tub so the control can reach and maintain the selected temperature. Replacing a failed element restores proper heating performance and helps return cycle times to normal. What it does:

• Heats the water in the washer's tub during applicable cycles
• Helps the control reach and hold target temperatures for better cleaning
• Failure symptoms can include cold wash water, extended cycle times, and reduced cleaning performance
• Visual damage or an open circuit on the element indicates replacement is needed

• 1 heater assembly

• Disconnect power and turn off water before servicing
• The heater mounts at the bottom of the outer tub; remove front or rear panels as required by your model to access it
• Note wire locations; loosen the center nut, press the stud to release the old seal, and carefully withdraw the element
• Seat the new gasket evenly, tighten the nut to compress the seal, then run a test cycle to check for leaks and proper heating

This clamp secures flexible hoses to fittings to prevent leaks and keep connections tight. It's a simple replacement that restores a secure seal on water and drain lines. What it does:

• Holds a hose firmly to a barb or nipple to prevent slipping and leaks
• Helps stop common symptoms like dripping, visible leaks, or a loose hose connection
• Keeps hoses from shifting or vibrating during operation
• Works wherever a small metal hose clamp is used on plumbing or drainage connections

• One clamp

• Turn off power and shut off water supply before replacing the clamp
• Slide the clamp over the hose, seat the hose on the fitting, then tighten or crimp per the clamp type
• Use pliers or the correct tool for the clamp to avoid damage to the hose or clamp
• Replace with the same clamp style and size for a proper fit; inspect hose and fitting for wear

This thermistor seal is the grommet that seals the temperature sensor where it passes through the washing machine's outer tub. Replacing a worn seal restores a watertight fit and helps prevent leaks that can damage surrounding components. What it does

• Forms a watertight barrier around the tub temperature sensor (thermistor)
• Helps keep the sensor securely positioned in the mounting port
• Common failure symptoms: water leaking during cycles, puddles under the unit, visible cracking/hardening of the grommet, or a loose sensor fit

• 1 thermistor seal

• Disconnect power and water; drain any remaining water from the tub
• Access the thermistor on the outer tub, disconnect its harness, and remove the sensor
• Pull out the old seal, clean the opening, press in the new seal, and reinstall the sensor fully seated
• Run a brief test cycle and check for leaks before final reassembly

This clamp secures flexible hoses to fittings to prevent leaks and keep connections tight. It's a simple replacement that restores a secure seal on water and drain lines. What it does:

• Holds a hose firmly to a barb or nipple to prevent slipping and leaks
• Helps stop common symptoms like dripping, visible leaks, or a loose hose connection
• Keeps hoses from shifting or vibrating during operation
• Works wherever a small metal hose clamp is used on plumbing or drainage connections

• One clamp

• Turn off power and shut off water supply before replacing the clamp
• Slide the clamp over the hose, seat the hose on the fitting, then tighten or crimp per the clamp type
• Use pliers or the correct tool for the clamp to avoid damage to the hose or clamp
• Replace with the same clamp style and size for a proper fit; inspect hose and fitting for wear