Parts for Ge TFEA22RRAAD: 01 - Section1 Parts

Hardware fasteners for securing refrigerator door panels and components. Includes screws, nuts, and washers for assembly. Replace missing or stripped pieces.

Handle insert channel for refrigerator doors. Replaces cracked, broken, or missing channels that secure the door handle. Direct fit component.

This replacement part is a handle bar, and it is intended for use in different types of appliances. This is a genuine replacement part made by General Electric. Each refrigerator typically has two handle bars which allow the user to open and closed the doors effectively and efficiently. A new handle bar might be needed if the current one is unable to stay connected to the door of the appliance. It is possible that the screws in this part can become stripped and therefore not hold the handle bar in place. It is best to replace this part immediately as the user might not be able to open the appliance at all if the handle becomes completely detached. This repair is simple and should only take a few minutes. Using a screwdriver, remove the old handles and replace the new ones securely on the door. This handle bar cover is sourced directly from the manufacturer. This is a genuine OEM replacement part and is sold individually.

Replace your cracked or broken refrigerator door handle channel. This structural component secures the handle assembly to the door for smooth operation.

Mounting screw for refrigerator internal components. Replaces lost, stripped, or damaged screws used to secure panels, brackets, and parts inside your unit.

This replacement part is a door hinge, and it is intended for use in different types of appliances. This is a genuine replacement part made by General Electric. This door hinge is typically found in refrigerators or freezers. The hinge is stationed so that the door and the main parts of the appliance are connected and in working order. The door hinge allows the doors to be opened and closed easily and smoothly. There is typically more than one hinge on each door so be sure to purchase the correct amount. A new door hinge might be needed if the current appliance doors are not properly opening and closing. Another way to tell if the hinges are damaged is if the doors are drooping and require a slight lift to be shut. This usually means the hinges are becoming loose and either need to be tightened or replaced altogether. Note that the doors will have to be completely removed to replace this part so the food inside the fridge may go bad during the repair if it takes too long. This is a genuine OEM replacement part and is sold individually.

Plastic cam riser that lifts and aligns the refrigerator door as it opens and closes. Replace if cracked, broken, or missing to restore smooth operation.

Spring for recess duct. For spring sleeve use WR2X4822.

This part has been discontinued by the manufacturer and is no longer available.

This dispenser sleeve comes with plunger, sleeve, and screw.

Lanyard for dispenser door.

Dispenser selector lever for refrigerators. Installs on selector switch assembly. Replace if cracked, broken, or missing to restore proper operation.

Includes 12 screws.

Molded housing that supports and aligns refrigerator dispenser components. Replace if cracked, broken, or no longer holding chute and actuator securely.

This part has been discontinued and is no longer available.

Ice maker dispenser door.

Time delay display arm.

Replace missing or stripped mounting screws in your washer dryer combo. This 12-pack secures panels, components, and internal parts during assembly or repair.

Includes 12 washers.

Ice chute door lever for refrigerator dispensers. Replaces broken, cracked, or missing levers that control ice door opening and closing.

This is the right side duct gasket. For left side use WR14X247.

This is the left side duct gasket. For right side use WR14X246.

Support bracket that holds the cradle switch in your refrigerator. Replace if the original is cracked, broken, or missing to properly secure the switch.

Protection spring that secures and guards wiring or tubing in your refrigerator. Replace if spring is broken, missing, or no longer holding tubes securely.

Secures wire harnesses in your refrigerator. Replace if broken, cracked, or wires are loose. Confirm fit with your model number before ordering.

Connects water supply tubing sections in your refrigerator. Replace this plastic compression union if it's cracked, leaking, or broken. Installs inline.

Includes 12 screws. Size: 8-18 ab.

Replace your broken or missing refrigerator door shelf end cap hook. This support piece secures the shelf bar in place on side-by-side models.

Utility compartment trim piece for refrigerators. Installs around utility storage area. Replace if cracked, broken, discolored, or missing.

Color: clear. Measures about 16 inches wide by 7 inches high.

Stainless steel #6-20 screw (1/2" length) secures panels, brackets, and internal components. Replace if missing, stripped, or corroded for a tight fit.

This part has been discontinued and is no longer avaialble.

Replace the end cap trim on your refrigerator door handle. This decorative trim piece covers the handle end and may need replacement if cracked or missing.

Replacement 8-18 x 9/16 machine screw for securing panels, brackets, and internal components. Needed when fasteners are stripped, missing, or worn.

Includes 12 screws.

Includes 12 screws.

Size: 10-16 ab.

Size: 8-32 t. Includes 12 screws.

Replacement mounting screw for securing panels, trim, and internal brackets. Needed when original fasteners are missing, stripped, or damaged.