Parts for Kenmore 253.7041341B (2537041341B, 253 7041341B): Shelves Parts

The Air Filter is an OEM part for Frigidaire refrigerators designed to enhance the air quality inside the refrigerator, ensuring that food stays fresh and odor-free.

The Air Filter helps to remove unwanted odors and impurities from the refrigerator's circulating air. It absorbs and neutralizes common food odors, keeping your fridge smelling clean and pleasant. The activated carbon filter is 7 times more effective than baking soda at removing odors. 

For best results, change filter every 6 months. 
Color: Black. 
Measures about 7 inches wide by 5 inches deep. 

Symptoms of a bad air filter include:

• Lingering food odors inside the refrigerator
• Increased presence of stale or unpleasant smells
• Decreased effectiveness in eliminating odors

Replace your Air Filter with this genuine part to ensure a clean and fresh-smelling refrigerator. This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This refrigerator water inlet tube routes water from the supply/valve into the appliance's water system. Replacing a cracked or kinked tube restores proper flow to the dispenser and ice maker while helping prevent leaks.

• Directs water from the inlet valve to internal components for dispensing and ice production
• Maintains a sealed, food-grade water path
• Replace if you notice leaks under/behind the unit, visible cracks/kinks, reduced or intermittent dispenser flow, or ice maker not filling
• Normal wear, brittleness, or damage during moves can lead to failures

• Disconnect power and shut off the water supply before servicing
• Place a towel or tray to catch residual water when disconnecting lines
• Note the original routing; release any retaining clips and disconnect the tube from fittings
• Route the new tube exactly like the original and fully seat tube ends in connectors; restore water and check for leaks

This replacement screw secures appliance components in place. Use it to replace a missing, stripped, or rusted fastener so shelves, handles, panels, or brackets stay properly mounted and the unit operates without unwanted movement.

• Fastens components to the cabinet, door, liner, or frame
• Restores a solid fit when the original screw is worn or lost
• Helps eliminate looseness, rattling, or misalignment
• Matches the original hardware for correct fit and thread engagement

• Disconnect power before servicing; for refrigerators, also turn off the water supply
• Align parts and start the screw by hand to avoid cross-threading
• Tighten with the correct driver; do not overtighten, especially into plastic
• If receiving threads are damaged, repair or replace the mating clip/bracket before installing

The Drawer Cover is an OEM part for Frigidaire refrigerators. It is designed to cover and protect the drawers within the refrigerator, providing a stable surface and helping to maintain the optimal temperature and humidity levels for the stored food.

Over time, the drawer cover can become damaged or worn out. Causes of a bad drawer cover can include frequent use, heavy loads placed on top of the cover, or accidental impact or cracks.

Symptoms of a bad Drawer Cover include:

• Cracks or breaks in the cover
• Difficulty sliding the drawers in and out
• Reduced effectiveness in maintaining drawer temperatures and humidity

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Does not include the wheel, part number 5304508016

The Crisper Pan is an OEM part for Frigidaire refrigerators. This part stores fruits and vegetables at optimal humidity levels, helping to keep them fresh for longer periods.

Causes of a bad crisper pan can include wear and tear from frequent use, accidental impacts, or exposure to heavy weights that cause it to crack or break.

Symptoms of a bad crisper pan include:

• Cracks or breaks in the pan
• Difficulty sliding the pan in and out
• Food not staying fresh due to improper sealing
• Visible damage that affects its functionality

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Crisper Cover Rail is an OEM replacement part for Frigidaire refrigerators. Located inside the fresh food compartment, this plastic rail securely guides and supports the right side of the crisper drawer's hinged cover.

Causes can be breakage from repetitive drawer movements over years of use. Normal wear may also cause loss of the rail's stabilizing function.

Symptoms of a faulty rail include:

• The crisper cover becoming loose or misaligned when opening/closing
• Difficulty fully closing or fastening the cover securely
• Damage to the adjacent cover frames from improper rail alignment

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore ranges.

The Rail, Crisper Cover, LH Side is an OEM part for Frigidaire refrigerators. This rail supports the left-hand side of the crisper cover, allowing it to slide in and out smoothly. It helps maintain the stability and functionality of the crisper drawer, ensuring easy access to stored fruits and vegetables. Wheel not included, use part number AP6230456

Causes of a bad crisper cover rail can include regular wear and tear, heavy loads causing stress on the rail, or accidental damage from removing or inserting the crisper drawer. A damaged rail can lead to difficulties in opening or closing the crisper drawer properly.

Symptoms of a bad crisper cover rail include:

• The crisper drawer not sliding smoothly or getting stuck
• The crisper cover being unstable or misaligned
• Visible cracks or damage to the rail
• The crisper drawer falling out of place

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This shelf channel is the metal/plastic support that secures and aligns a refrigerator shelf or door bin, helping keep stored items stable and properly positioned. It restores proper shelf fit and prevents sagging or misalignment. What it does:

• Provides a secure mounting track for a refrigerator shelf or door bin
• Supports shelf weight to prevent bowing, shifting, or falling
• Keeps the shelf aligned so items sit level and doors close smoothly
• Helps restore original shelf fit after damage or wear

• One shelf channel mounting piece

• High-level replacement; inspect adjacent clips and fasteners and replace if damaged
• Use proper hand tools; avoid overtightening to prevent cracking
• Disconnect power only if working near electrical components; otherwise power removal is not typically required

This shelf channel is the replacement mounting rail that supports and secures a refrigerator shelf, restoring stable shelf alignment and load support. Use it when a shelf slides out of position or the mounting rail is cracked or bent. What it does:

• Provides the mounting surface and guide for a refrigerator glass or wire shelf
• Restores proper shelf alignment and prevents sagging or uneven seating
• Replaces damaged, cracked or bent shelf rails that allow shelves to shift
• Helps maintain safe storage by keeping shelves locked in place during use

• Basic hand tools required; follow the refrigerator's service diagram for exact removal and replacement steps
• Support the shelf when removing the old channel to avoid dropping or damaging the shelf
• Disconnect power (or unplug) the appliance if working near electrical components or lighting
• Replace any fasteners, clips or adjacent trim that are damaged to ensure proper fit and secure mounting

Color: Black/natural. Nylon

The Water Filter is an OEM component specifically designed for Frigidaire refrigerators with built-in filtration systems. This filter removes contaminants and improves the taste of water distributed through the unit.  

Causes of a bad water filter include scale buildup over time reduced capacity, dried-out media failing to adsorb impurities, or torn casings leaking untreated water.

Symptoms of a bad water filter include:

• Diminished filter life unable to meet Gallon ratings  
• Tests indicating low flow or untreated bacteria/lead  
• Change filter reminders triggering prematurely
• Contaminants detected in ice or dispenser water

Replace yours today with this genuine OEM Frigidaire filter to restore freshness. Compatible with Gibson, Kenmore, and Electrolux models as well, proper filtration sustains appliance performance while satisfying health standards.

Color: white. Measures about 2 inches wide by 2 inches high by 11-1/2 inches deep.

This water filter base secures the refrigerator's replaceable water filter cartridge and directs filtered water to the dispenser and icemaker. Replacing a damaged base restores a proper seal and helps prevent leaks and flow interruptions. What it does:

• Holds and seals the water filter cartridge so water passes through the filter media
• Directs filtered water to the dispenser and icemaker plumbing
• Prevents leaks caused by cracked or worn filter housing
• Can resolve low water flow, intermittent dispensing, or water taste issues when base is leaking or not sealing

• One water filter base assembly

• Turn off refrigerator and shut off the water supply before starting
• Relieve system pressure by dispensing water until flow stops, if applicable
• Remove the old housing carefully; inspect O-rings and replace if damaged
• Hand-tighten only; check connections and test for leaks after restoring water and power

This water filter cover encloses the refrigerator's filter housing for a clean look and protection. Replace a cracked, loose, or missing cover to restore a secure, smooth-opening access door for routine filter changes.

• Covers and protects the water filter in the fresh food compartment
• Opens to provide access when replacing the filter
• Helps prevent items from catching on the filter or housing
• Replace if the cover is cracked, the hinge or latch is broken, it won't stay closed, or it's missing

• Disconnect power and shut off the water supply before servicing
• Open the filter area and release the retaining tabs or hinge pins to remove the old cover
• Transfer any screws or hinge pieces from the original part if required
• Align and snap or secure the new cover; verify smooth opening and closing

This water filter housing is the refrigerator-mounted enclosure that holds and seals the replaceable water filter cartridge, helping ensure proper water flow to the dispenser and icemaker. Fits factory filter systems and restores secure filter seating. What it does:

• Houses and secures the refrigerator water filter cartridge to maintain a sealed water path
• Directs filtered water to the dispenser and icemaker while preventing leaks when installed correctly
• Can help stop water bypass or weak flow caused by damaged or cracked housings
• Supports proper alignment for O-rings and filter locking/engagement

• One water filter housing designed for the factory filter location

• Turn off the refrigerator water supply and dispense any residual water before servicing
• Remove power to the appliance if required by your model and follow manufacturer safety guidance
• Inspect and replace associated O-rings or seals if worn; confirm proper seating to prevent leaks

This refrigerator water filter mount secures the filter head/housing to the liner so the cartridge seats squarely and seals. Replace a cracked or loose mount to restore a snug fit and help prevent leaks or vibration.

• Holds the water filter housing firmly in place
• Aligns the cartridge for proper engagement with the filter head
• Helps maintain a watertight seal at the filter connection
• Common symptoms: filter won't lock in or sits crooked, drips around the filter area, difficulty installing/removing the filter, or rattling from a loose housing

• Disconnect power and shut off the water supply; dispense water to relieve line pressure
• Remove the filter and any cover/trim to access the mount; retain existing screws for reuse
• Install the new mount and tighten screws gently to avoid cracking plastic
• Reinstall the filter, restore water and power, flush the dispenser, and check for leaks

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

The Crisper Pan Roller is an OEM replacement part for Frigidaire side-by-side refrigerators. Located in drawer tracks below crisper bins, these rollers facilitate smooth extension and retraction of crisper pans.

Symptoms of damaged crisper pan rollers include: 

• Difficulty fully withdrawing or pushing in crisper pans  
• Jumpy or uneven movement of pans on drawer slides
• Visible scratches or flattened spots on roller surfaces  
• Creaking or grinding noises emanating from drawer area

Causes relate to repeated weight impacts over years absorbing crisper loads containing vegetables and fruits. Rust accelerates on rollers exposed to humidity fluctuations inside drawers.

This pan roller is compatible with select Electrolux and Kelvinator models as well.

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

This refrigerator clip is a small retainer that secures a component in place so it stays properly seated during use. Replacing a worn or missing clip restores a snug fit and helps eliminate looseness, rattling, or misalignment.

• Holds a part, panel, tube, or wire securely in its mounting point
• Maintains alignment to prevent shifting or vibration
• Helps preserve proper fit and airflow when components are correctly seated
• Symptoms can include loose or sagging pieces, rattling noises, or parts that won't stay attached

• Unplug the refrigerator; if working near water lines, shut off the water supply
• Note the clip's orientation before removal; take a photo for reference
• Use needle-nose pliers to release/install; avoid over-flexing the clip
• After installation, tug-test gently to confirm a secure fit before reassembling

This replacement screw secures appliance components to their mounting points so panels, brackets, and trim stay tight and aligned. Replace missing or stripped hardware to restore a solid, rattle-free fit and proper assembly integrity.

• Secures panels, brackets, and trim to prevent movement and maintain alignment
• Replaces missing, damaged, or stripped hardware that can compromise assembly
• Helps reduce rattling or vibration from loose components
• Restores proper fit after service or access panel removal

• Unplug the appliance before servicing; turn off water supply if working near dispenser/ice areas
• Compare the new screw to the original to ensure thread, head style, and length
• Start threading by hand to avoid cross-threading; tighten snugly without over-torquing, especially into plastic
• Retain and reuse any original washers, spacers, or clips as required

This refrigerator water inlet tube routes water from the supply/valve into the appliance's water system. Replacing a cracked or kinked tube restores proper flow to the dispenser and ice maker while helping prevent leaks.

• Directs water from the inlet valve to internal components for dispensing and ice production
• Maintains a sealed, food-grade water path
• Replace if you notice leaks under/behind the unit, visible cracks/kinks, reduced or intermittent dispenser flow, or ice maker not filling
• Normal wear, brittleness, or damage during moves can lead to failures

• Disconnect power and shut off the water supply before servicing
• Place a towel or tray to catch residual water when disconnecting lines
• Note the original routing; release any retaining clips and disconnect the tube from fittings
• Route the new tube exactly like the original and fully seat tube ends in connectors; restore water and check for leaks

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head