Parts for Thermador T30IR70CSS-01: Shelves Parts

This active carbon filter refreshes the air when your range hood is set to recirculate. Replace a saturated filter to restore effective odor reduction and maintain a more comfortable cooking space. What it does:

• Adsorbs cooking odors in recirculating operation
• Helps maintain fresher indoor air when venting back into the room
• Restores odor-removal performance when the old filter is saturated
• Typical signs it's time to replace: persistent cooking smells or diminished odor reduction

• One activated carbon filter

• Disconnect power to the hood before servicing
• Remove the metal grease filter(s) to access the charcoal filter
• Release the old filter from its clips/bayonet mount and install the new filter in the same orientation until it locks
• Charcoal filters are not washable; replace when saturated

• For hoods configured for recirculation; not used when vented to the outdoors

A replacement round glass turntable plate that supports dishes and provides a stable rotating surface for even microwave heating. Fits models designed for a 10–13 inch diameter glass tray and restores proper turntable function. What it does:

• Replaces a cracked, chipped, or missing microwave glass turntable to allow dishes to rotate during cooking
• Provides a stable, heat-resistant surface for plates, bowls and cookware
• Helps improve heating consistency by allowing the turntable to rotate as intended
• Works with the oven/microwave's roller guide and turntable motor when properly seated

• One glass turntable plate

• Handle carefully — glass can break if dropped; inspect for cracks before use
• Clean with mild detergent; avoid abrasive cleaners that can damage the surface
• Make sure the plate is properly seated on the roller guide/drive coupling before operating
• Do not use if damaged; replace immediately to avoid injury or further appliance damage

This replacement rail serves as the track that supports and guides a sliding rack, shelf, or drawer in your appliance. Replacing a worn rail restores smooth, level movement and helps prevent binding or misalignment during everyday use.

• Provides the track surface for a rack, shelf, or drawer to slide in and out
• Keeps the moving assembly aligned and supported during operation
• Helps ensure smooth travel and consistent extension/retraction
• Common symptoms of a worn rail include sticking, rough or noisy movement, crooked travel, or a rack/drawer that drops off the track

• Disconnect power to the appliance; shut off the water supply before servicing
• Remove the rack/drawer and retain hardware; transfer original screws or clips to the new rail
• Match the orientation and side of the original rail during installation
• After install, cycle the rack/drawer to ensure smooth operation; inspect the mating rail and rollers and replace if excessively worn

This rack rail guides the lower dishwasher rack smoothly in and out, restoring proper rack movement and alignment for reliable loading and unloading. It replaces a worn, bent, or broken slide rail to reduce sticking and mis-tracking. What it does:

• Guides and supports the lower dish rack so it slides smoothly on the dishwasher track
• Replaces damaged or bent rail that causes the rack to stick, bind, or wobble
• Helps keep the rack aligned to prevent dishes from tipping or not seating properly
• Works with the rack rollers/tires and end stops to ensure consistent movement

• One rack rail

• Intended to be installed by someone comfortable with basic appliance repairs; disconnect power and water before beginning
• Remove the lower rack and any end caps/fasteners holding the old rail; align and snap or fasten the new rail per the OEM layout
• Keep small clips and screws secured during reassembly; test rack movement before returning the dishwasher to service

A small retaining clip that fastens a component or panel in place inside your appliance. Replacing a broken or missing clip restores a secure fit so parts stay aligned and don't rattle during operation.

• Holds a mating piece, trim, or cover securely in position
• Helps prevent vibration-related looseness, gaps, and rattling
• Restores proper fit when the original clip is cracked, bent, or missing
• Common signs: loose or wobbly part, misalignment, visible damaged/missing clip

• Disconnect power; shut off water or gas supply
• Note the original clip's orientation; take a photo before removal
• Use needle-nose pliers to release/install; avoid prying on brittle plastics
• Press until fully seated and verify secure engagement before reassembly

The Freezer Clip is an OEM part for Bosch refrigerators. It is designed to secure various components within the freezer compartment, ensuring they remain in place during regular use and while opening and closing the freezer door.

Causes of a bad freezer clip can include wear and tear over time, breakage due to handling or impact, or exposure to extreme temperatures that cause the clip to become brittle and snap. Ensuring the clip is intact and functioning properly is essential for maintaining the organization and efficiency of the freezer space.

Symptoms of a bad freezer clip include:

• Items or shelves in the freezer becoming dislodged
• Difficulty in keeping freezer components in place
• Unusual noises from components moving within the freezer

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Freezer Clip is an OEM part for Bosch refrigerators. It is designed to secure various components within the freezer compartment, ensuring they remain in place during regular use and while opening and closing the freezer door.

Causes of a bad freezer clip can include wear and tear over time, breakage due to handling or impact, or exposure to extreme temperatures that cause the clip to become brittle and snap. Ensuring the clip is intact and functioning properly is essential for maintaining the organization and efficiency of the freezer space.

Symptoms of a bad freezer clip include:

• Items or shelves in the freezer becoming dislodged
• Difficulty in keeping freezer components in place
• Unusual noises from components moving within the freezer

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This replacement glass plate restores a stable, heat-resistant surface for microwave cooking and reheating. It supports dishes while the microwave's turntable system rotates to promote even heating and safe food placement. What it does:

• Provides a flat, durable surface for plates, bowls and cookware used in the microwave.
• Restores proper rotation and support if the original glass is cracked, chipped, scratched or missing.
• Helps prevent uneven heating caused by unstable or damaged turntable surfaces.
• Reduces risk of dishes tipping during use when installed correctly.

• Unplug the microwave and allow it to cool completely before handling internal components.
• Verify the turntable support ring and rollers are in place and undamaged before setting the new glass plate into position.
• Center the plate on the turntable support so it mates correctly with the motor coupling; do not force or rotate by hand.
• Do not use a cracked or chipped glass plate; replace immediately to avoid safety hazards. Hand wash with mild detergent; avoid abrasive pads.

This replacement plate secures and stabilizes internal components, restoring proper alignment and reducing wear. It's a direct-fit part designed to keep moving assemblies seated so the appliance runs quietly and reliably. What it does:

• Provides a stable mounting surface to keep internal parts properly aligned
• Helps prevent vibration and rattling from loose or shifting components
• Reduces wear by maintaining correct part positioning during operation
• Can address symptoms such as unusual noise, misalignment, or intermittent contact

• Disconnect power and water before starting any repair
• Follow OEM service manual instructions for access and removal of surrounding parts
• Use appropriate hand tools; avoid over-tightening fasteners to prevent damage

This electronic control board manages the appliance's user interface and key control functions, restoring normal control and cycle operation when the original board has failed. It replaces a faulty main control to help the appliance respond to commands. What it does

• Receives input from the control panel and sends signals to start and stop cycles.
• Controls power distribution to motors, pumps, valves, and heaters as designed.
• Can correct symptoms like unresponsive buttons, failure to start, or erratic cycle behavior.
• May clear certain control-related error codes when replaced.

• Disconnect power to the appliance before starting any work.
• Handle the board carefully to avoid static damage; use ESD protection if available.
• Installation typically requires access by removing the control console or inner panel and disconnecting wiring harnesses.