Parts for Universal Multiflex (Frigidaire) MRTN23V6MW4: Shelves Parts

Optional flexible ice tray for those that dont have an icemaker

Wire shelf for refrigerator freezer compartment. Replace your cracked, rusted, corroded, or missing freezer shelf. Direct fit replacement part.

Uneven cooling or warm spots in your fridge? This top air diffuser directs cold airflow to maintain consistent temperatures. Simple DIY repair.

Warm spots in lower fridge? This bottom air diffuser directs cold air to maintain even temperatures. Simple snap-in installation restores airflow.

Refrigerator interior light won't turn on or stays on? This door light switch controls your fridge lighting. Quick DIY fix with basic tools.

Replacement interior light bulb for refrigerators. Restores visibility inside compartments when original bulb burns out. Verify fit with your model number.

Refrigerator light won't turn on or flickers? A faulty light socket is often the cause. This snap-in replacement restores interior lighting in 10 minutes.

Houses and protects electronic controls and wiring in your refrigerator. Replace if cracked, broken, or drain tube connection damaged causing water leaks.

Replace a cracked, broken, or missing temperature control knob on your refrigerator. Installs on the control shaft to restore accurate temperature selection.

Refrigerator not cooling or freezing? A faulty temperature control thermostat causes inadequate cooling. DIY repair in 5-10 minutes with basic tools.

Replacement water tube for refrigerators. Routes water between components like the inlet valve and dispenser. Replace if cracked, leaking, or damaged.

Fix frost buildup in your refrigerator with this defrost control board. Regulates defrost cycles to prevent ice accumulation and maintain efficiency.

Humidity control slide for refrigerator crisper drawers. Replace if broken, cracked, or missing to restore adjustable ventilation for fresh produce storage.

Crisper drawer humidity control slide for refrigerators. Replaces broken, cracked, or stuck humidity adjustment slider on fresh food drawers.

Replace your broken or cracked refrigerator crisper pan. This drawer holds fruits and vegetables in the bottom of your fridge. Easy installation.

Replace your cracked, broken, or damaged refrigerator meat pan. This drawer installs in the fresh food section to store meats and perishables separately.

Missing or cracked ice bin? This ice bucket stores ice from your refrigerator's ice maker. Simple pull-out replacement installs in seconds.

Cantilever half shelf frame for top-mount refrigerators. Replace this structural part if your existing frame is cracked, broken, or damaged.

Cosmetic trim piece that covers the front edge of refrigerator shelves. Replace if cracked, broken, or missing to restore a clean, finished look.

Left-hand meat pan hanger that mounts to the refrigerator side wall to support the meat pan. Replace if cracked, broken, or missing for secure pan storage.

Right-side hanger rail that mounts under the top shelf to support the meat pan drawer. Replace if broken, cracked, or no longer holding the pan securely.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.

This replacement screw secures panels, brackets, and other components in your appliance. Replace missing or stripped hardware to restore a tight, rattle-free fit and keep assemblies aligned the way the manufacturer intended.

• Fastens the designated component to the appliance cabinet or assembly
• Helps reduce looseness, vibration, and rattling
• Replaces missing, corroded, or stripped screws
• Supports proper alignment of panels, trim, and brackets

• Disconnect power and, if applicable, shut off gas/water before servicing
• Match the screw to the original location; retain any reusable clips or washers
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten into plastic or thin metal

This is a replacement mounting screw used to secure the defrost timer assembly to the refrigerator control housing, restoring proper fastening and preventing the timer from shifting or vibrating during operation. What it does:

• Secures the defrost timer to the control housing so the timer stays in position.
• Prevents vibration or movement that can cause intermittent contact or noisy operation.
• Helps maintain reliable defrost cycle timing by keeping the timer properly aligned.
• Addresses symptoms such as a loose or missing fastener, rattling behind the control panel, or a timer that shifts when the door is opened.

• Unplug the appliance before starting work to prevent electrical shock.
• Access the control housing or timer bracket per your model's service instructions.
• Use the correct screwdriver or driver bit; do not overtighten—stop when snug to avoid stripping.
• Retain removed hardware for reference and compare screw length/threads before installing.