Parts for Frigidaire FRTD2021AB0: System Parts

Includes service line.

Fix unresponsive controls, displays not working, or intermittent power issues. This main wiring harness restores electrical connections between components.

Fix excessive frost buildup on evaporator coils with this refrigerator defrost heater assembly. Heats coils during defrost cycle to prevent ice formation.

Aluminum strap secures the defrost heater against the evaporator coil. Replace if broken, cracked, or missing to maintain proper heater contact.

Channels defrost water from the evaporator to the drain pan. Replace if cracked, broken, or leaking to prevent water pooling in the fresh-food compartment.

This is a replacement mounting bracket designed to secure appliance components in place for stable operation and reliable alignment. It restores proper support where a damaged or missing bracket is causing fit or stability issues. What it does:

• Provides a secure mounting point to hold panels or internal components in place
• Restores alignment to doors, panels, or assemblies that shift or sag
• Helps eliminate rattling or vibration caused by loose or broken supports
• Matches OEM fit for direct replacement when the original bracket is worn or broken

• Install with the original fasteners where possible; replace any stripped or damaged screws
• Ensure the appliance is unplugged or power is disconnected before accessing internal areas
• Use basic hand tools; avoid overtightening fasteners which can deform the bracket or mating parts

Secures the compressor to the mounting bracket in your refrigerator. Replace if washer is missing, cracked, or worn to restore proper support.

Secures the compressor to the chassis, reducing movement and noise. Replace if your compressor shifts or rattles during operation. Confirm fit with model.

Fix a refrigerator that won't cool or runs constantly with this compressor kit. Includes the compressor and electrical components needed to restore cooling.

Fix a refrigerator that won't cool or runs constantly with this compressor starter relay. Essential sealed system component for reliable operation.

Black rubber mounting grommet that secures tubes and wires in your refrigerator. Replace if cracked, worn, or missing to properly hold components in place.

This #8-32 x 3/8 screw secures appliance panels, brackets, and assemblies. Replace a missing or stripped fastener to keep parts tight and aligned, reduce vibration, and restore proper fit in compatible refrigerators and freezers.

• Machine-thread fastener sized #8-32, 3/8-inch length
• Secures control housings, trims, covers, and support brackets per model design
• Replaces missing, worn, or corroded screws that cause loose or rattling parts
• Helps maintain alignment and stability after service

• Unplug the appliance; shut off water if applicable
• Match thread size to the original and start by hand to avoid cross-threading
• Use the correct driver; do not overtighten, especially into plastic
• Verify component alignment and operation after fastening

• Thread size: #8-32
• Length: 3/8 inch

Secures wire harnesses and ground wires to your refrigerator cabinet. Replace if broken or missing to prevent wire damage. Verify fit with your model.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.

The Capacitor is an OEM part for Frigidaire refrigerators. It is part of the refrigerator's electrical system, responsible for providing a boost of power to start the compressor.

A bad capacitor can be caused by electrical issues, component failure, or damage. When the capacitor becomes faulty, it can result in issues such as the compressor not starting, inadequate cooling, or the refrigerator not running at all.

Symptoms of a bad capacitor include:

• The refrigerator not cooling properly
• Unusual noises from the compressor 
• Compressor turning on and off rapidly
• The refrigerator not running at all

Replace your faulty capacitor with this genuine OEM Frigidaire part to restore your refrigerator. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

Secures and organizes wiring harnesses in your refrigerator. Replace if broken, cracked, or wires are loose. Confirm fit with your model number.

Replacement mounting screw secures panels, brackets, and trim inside refrigerators and freezers. Restores factory assembly when original fasteners are missing.

Positions the condenser fan and motor in the rear machine compartment. Replace if cracked, warped, or damaged to restore proper airflow direction.

This is an electric fan motor that drives the condenser fan, typically located near the compressor at the bottom or rear of the refrigerator. It circulates air over the condenser coils to dissipate heat and maintain efficient cooling. Replace this motor if the refrigerator is running warm, the compressor is overheating, or you no longer hear the condenser fan running when the compressor is on.

Refrigerator not cooling properly? A damaged condenser fan blade prevents airflow over the condenser coils. Quick DIY fix—simply push into place.

Supports refrigerator crisper or bin drawers for smooth gliding. Replace when drawers stick or bind. Confirm fit with your model number listed.

Metal rivet fastener permanently secures panels, brackets, and internal components in refrigerators. Replace damaged, missing, or worn rivets to restore fit.

This replacement water fill tube directs water from the refrigerator supply to the ice maker or water dispenser, helping restore proper filling and reduce leaks from cracked or clogged tubing. It's a direct-fit service part. What it does

• Channels water from the supply line to the ice maker or dispenser for normal fill cycles
• Helps stop leaks or drips caused by cracked, kinked, or deteriorated tubing
• Restores consistent fill volume when original tubing is damaged or plugged
• Works with factory fittings and routing to maintain correct water flow

• One replacement water fill tube

• Turn off the refrigerator and shut off the water supply before starting
• Disconnect electrical power and relieve water pressure by disconnecting the supply briefly
• Use proper fittings and hand tools; tighten connections to OEM torque recommendations to prevent leaks
• Inspect nearby clamps and valves during replacement and replace any worn parts

Secures the evaporator or condenser fan shroud to the refrigerator cabinet. Replace this mounting screw if stripped, missing, or broken during repair.

Replacement mounting screw for refrigerators, ovens, ranges, and cooktops. Secures interior panels, components, and trim. Needed when original is stripped, missing, or damaged during repair.

Foam seal tape creates airtight barriers around refrigerator components. Replace when worn, compressed, or damaged to restore proper sealing and efficiency.

Secures tubes and wiring in your refrigerator. Replace if clips are broken or connections are loose. Confirm fit with your model number.

Secures refrigerator grille or trim to cabinet, preventing rattles and gaps. Replace when broken or missing to restore proper panel alignment. Verify fit with your model number before ordering.

Positions and secures condenser tubing to maintain proper spacing. Replace if worn, broken, or missing to prevent vibration, rattling, and tube damage.