Parts for Generac XG8000E-5747-2: Tank Assy Parts

This plastic body fuel shutoff valve is a genuine OEM replacement part for portable Generac generators. It is an inline fuel valve that is responsible for controlling the flow of gas from the tank to the engine. It is also responsible for stopping fuel from reaching the engine if the generator is not in use. If the fuel shutoff valve is damaged due to normal wear and tear or leaking when not in use, it should be removed and replaced.Repairs involving fuel should be made in an area with adequate ventilation. All fuel should be drained from the fuel tank and fuel lines before removing the valve. Pliers, a screwdriver, gloves, and a basin or tub to drain the fuel are necessary for making the repair. Locate the clamps holding the fuel line on each side and use pliers to release them. Remove the old valve and insert new valve. Replace the fuel lines and reclamp. Refill the fuel and check for leaks.This fuel shut off valve is made of heavy-duty molded plastic and sold as an individual unit. It is made specifically for portable generators manufactured by Generac.

This fuel filter keeps dirt and foreign objects out of the fuel system of Generac generators. Fuel, particularly when stored in portable fuel tanks, is prone to getting dirt and debris in it. Before using it in a generator or other piece of equipment, the debris needs to be removed. If the dirt and debris are not removed from the fuel, it can enter the fuel system and cause damage. The fuel filter prevents this from happening.Fuel filters need to be examined and replaced as part of routine maintenance. A visual inspection will show if the filter is dirty or not. If dirty, the filter is easily removed with a pair of pliers. The new filter can be put into place using your hands. The process normally takes less than twenty minutes. All dirt and contaminating particles are not visible to the naked eye. The fuel filter should be replaced according to a scheduled maintenance plan, regardless of visible dirt and debris. This OEM fuel filter comes directly from the manufacturer and is used in Generac portable generators. The overall part is made of plastic and contains a mesh filter. It is sold individually.

This is an alternator vibration mount or isolator that is intended for use with generators. This piece attaches to the alternator to help to dampen or soften the amount of vibration that comes from the generator. It is a simple part, but if it is broken or not working properly, there may be a substantial amount of vibration and noise from the machine.The mount is made from durable materials and is made to last. However, this part can still start to wear down over time, or the metal pieces could become rusted. The threads could be damaged, as well. Regardless, it will need to be replaced when this happens.The alternator vibration mount is made for select models of generators from Generac. The piece is sold individually, and it is a genuine OEM replacement part.

This part is a 12-volt battery used on portable generators. The purpose of a battery is to provide the current needed to start the portable generator.A new 12-volt battery may be needed if the battery is dead and cannot be jump-started. Over time, batteries become weaker and need to be replaced after normal wear and tear over a period of time. If the portable generator will not turn on, it could be a result of a battery that has died or gone completely bad. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment. Use extreme care when handling a battery.This 12-volt battery is a genuine Husqvarna part. It is sold individually. This particular 12-volt battery is compatible with outdoor power equipment that are manufactured by the Husqvarna brand and the Generac brand.

This capacitor is a genuine OEM replacement part sourced directly from the manufacturer for use on generators. It regulates voltage and send volts to the rotor. If the generator has a lower than normal voltage reading or the generator's output is up and down, causing the output of power to surge and decrease, the capacitor should be removed and replaced. Use a voltage meter to check the capacitor to determine how much of a charge it is carrying.The capacitor needs to be discharged before it is removed and replaced to prevent electric shock. Always wear safety gloves when working on equipment. Disconnect the generator from all power sources and disconnect anything that is drawing power from the generator. Use a brand new insulated screwdriver to discharge the capacitor. Hold the capacitor in one hand and touch the screwdriver against both tips at the same time. The electricity will discharge. After the capacitor is discharged, unplug it from the generator. Install the new capacitor and make the necessary wire connections. Reconnect any items that were previously connected and test the generator.This capacitor is sold as an individual unit. It is specifically designed for generators manufactured by Generac.

This part is a replacement rollover valve. This is a genuine OEM part made by Generac and has been sourced directly from the manufacturer. This part can be used to replace a broken or defective rollover valve in a variety of generator models. Rollover valves are essential for safety when using a generator as they prevent pressure from building up inside the fuel tank and stop a vacuum from being created. It is always recommended that the appropriate safety precautions are adhered to when attempting to fix any power tools or machinery. When working on or near an engine, ensure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this rollover valve, the appropriate owner's manual and included diagrams should be referenced.As an authentic replacement part, this rollover valve is suitable for use on several different models of generators manufactured by Generac. This is a genuine part made of high-quality, durable materials and is sold individually.