Tappan Dishwasher Gasket & Seal

The Dishwasher Tub Gasket is an OEM replacement part for Frigidaire dishwashers. It seals the gap between the dishwasher tub and the door, preventing water leaks and ensuring efficient operation. This tub gasket is typically made of durable rubber or silicone material, designed to withstand the heat, moisture, and chemicals involved in the dishwashing process

Symptoms of a faulty Dishwasher Tub Gasket include:

• Water leaks around the dishwasher door or base
• Failure to maintain proper water levels during cycles
• Condensation buildup or moisture issues outside the tub area
• Visible cracks, wear, or damage to the gasket material

Causes of a bad tub gasket can include normal wear and tear over time, exposure to excessive heat or chemicals, or physical damage from mishandling or improper door closure.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore dishwasher models.

The Front O-Ring is an OEM part for Frigidaire dishwashers. This component is essential for maintaining a watertight seal in the front areas of the dishwasher's internal systems, such as around the pump or valve connections. It prevents water leaks and ensures the efficient operation of the dishwasher. The rear O-ring is part number AP2109101

Causes of a bad front O-ring can include regular wear and tear, exposure to high temperatures, and chemical degradation from detergents and rinse aids. Over time, the O-ring may dry out, crack, or become deformed, leading to leaks and decreased performance.

Symptoms of a bad front O-ring include:

• Water leaking from the front of the dishwasher
• Puddles forming under the appliance
• Reduced cleaning performance due to water pressure issues
• Noticeable wear, cracks, or deformation on the O-ring

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Rear O-Ring is an OEM part for Frigidaire dishwashers. This small but crucial component ensures a watertight seal within the dishwasher's internal systems, preventing leaks by sealing connections between various parts, such as the pump or valve assemblies. The front O-ring is part number AP2109102

Causes of a bad rear O-ring can include regular wear and tear, drying out or cracking due to age, and damage from chemical exposure or improper installation. A compromised O-ring can lead to water leaks and reduced efficiency of the dishwasher.

Symptoms of a bad rear O-ring include:

• Water leaking from the dishwasher
• Puddles forming underneath the appliance
• Reduced washing performance due to water pressure loss
• Noticeable wear, cracks, or deformation on the O-ring

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This sump gasket seals the connection between the dishwasher tub and the sump/pump assembly. Replacing a flattened or cracked gasket restores a watertight barrier to help stop leaks from the base and protect floors and cabinetry.

• Creates a seal between the tub and sump to contain wash water
• Helps prevent leaks during fill, wash, and drain cycles
• Replace if the gasket is cracked, brittle, deformed, or compressed
• Common symptoms: water under the dishwasher, dripping from the base, moisture around the toe-kick

• Disconnect power and shut off the water supply; pull the dishwasher out if needed for access
• Access the sump area (often by removing the lower rack, spray arm, and filters); note gasket orientation
• Clean mating surfaces; seat the gasket evenly without twists. Do not use sealants unless specified by the manufacturer
• Reassemble and run a short test cycle while inspecting for leaks

This pump gasket seals the connection between the appliance pump and housing to help prevent leaks and keep water flowing where it should. A simple replacement that restores a watertight pump interface. What it does:

• Creates a tight seal at the pump housing to stop water from leaking
• Helps maintain proper drain flow by preventing bypass leaks
• Commonly replaced when you see puddling or moisture under the appliance
• Can prevent intermittent draining issues caused by a compromised seal

• One pump gasket

• Disconnect power and water supply before starting any repair
• Inspect mating surfaces and clean debris before installing the new gasket
• Ensure the gasket seats fully and pump/housing fasteners are torqued to spec

This O-ring is a small rubber sealing gasket that prevents water leaks at a refrigerator water connection. It restores a watertight seal to stop drips and maintain proper water flow to the dispenser/ice system. What it does:

• Creates a watertight seal at a water line or valve connection
• Helps stop visible dripping or slow leaks from fittings
• Maintains proper pressure and flow by preventing bypass around a joint
• Used where a compressible seal is required between two mating parts

• Shut off water supply and disconnect power before servicing
• Replace only with the correct-size O-ring and seat it evenly in the groove
• Inspect mating surfaces for nicks or debris; clean before installing the new O-ring
• Tighten fittings to manufacturer torque recommendations to avoid over-compression

This refrigerator door gasket creates an airtight seal around the door to help maintain proper temperatures and energy efficiency. It replaces a worn, torn, or deformed seal to reduce cold air loss and cycling. What it does:

• Seals the refrigerator door to prevent cold air leakage and reduce frost buildup
• Helps maintain consistent internal temperatures for food safety
• Reduces compressor run time and saves energy when sealing properly
• Addresses common symptoms like warm spots near the door, visible gaps, or a torn/cracked seal

• One replacement door gasket

• Disconnect power to the appliance before starting any repair
• Clean and dry the door flange thoroughly before installing the new gasket
• Warm and flex the gasket as needed (hands or warm water) to ease installation and ensure full contact around the door
• After installation, close the door and check for gaps; allow 24 hours for the gasket to fully seat