Thermador Cooktop Control Board

The Control Board is an OEM part for Bosch wall ovens. It serves as the main control center for the oven, managing and regulating all the functions, including temperature settings, cooking modes, timers, and the operation of the heating elements. 

Causes of a bad Control Board can include electrical surges, wear and tear from prolonged use, exposure to heat, and moisture or grease buildup that can damage electronic components.

Symptoms of a bad Control Board include:

• The oven not powering on or failing to respond to control inputs
• Display errors or malfunctioning display screen
• Inaccurate temperature regulation or inability to maintain set temperatures
• The oven not completing cooking cycles or shutting off unexpectedly

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This factory fixing kit supplies the OEM hardware required to secure the appliance or designated components during installation or service. Replacing missing or damaged fasteners restores a solid, aligned mount so the unit stays stable without shifting, rattling, or gaps.

• Provides the correct hardware to fasten parts per your model's installation or service instructions
• Replaces stripped, corroded, or missing screws/clips that lead to looseness
• Helps maintain alignment and clearances to prevent gaps, rattles, or vibration
• Typical symptoms: loose mounting, panels that shift, or movement when opening/closing doors or drawers

• Disconnect power; shut off water or gas if applicable before starting work
• Follow the model-specific installation/service manual for attachment points and sequence; use the proper driver bit and do not overtighten
• Verify the unit is level and securely anchored; check clearances and operation after securing

This OEM part is a power control board. The power control board provides power to the electronic oven control board. If the oven is no longer turning on, or the digital display is no longer visible, this could mean it's time to replace the power control board. Luckily this is a relatively simple process.To begin, make sure to turn off the power to the oven by unplugging it or shutting off the circuit breaker. Then proceed to remove the upper back panel. Once removed locate the power control board and remove the wire harness and wires attached to it. Be sure to take note of the orientation of the wires to place them into the correct terminals on the new board. Attach the wires to the new board and snap the new board back in place. Resecure the back panel and put the oven back in place.This genuine replacement part is sold individually and is compatible with Bosch, Thermador, and Gaggenau ovens.

The Relay is an OEM component specifically designed for select Bosch built-in ovens. As a basic electronic switch, it receives signals from the control unit to energize heating elements. 

Durable plastic encapsulation protects delicate components from accidental spills. Precise switching facilitates customized baking and broiling temperatures within close tolerances.

Causes signaling relay failure related to prolonged thermal stresses from consistent oven use. Impacts of electric abnormalities could also cause malfunctions over time.

Symptoms requiring replacement include:  

• Inability to power top or bottom heating elements during cycles
• Erratic temperature fluctuations beyond adjustment capabilities
• Buzzing or loud clicking noises emitting from the relay housing

This OEM Bosch replacement part is also compatible with Thermador, Gaggenau, and select Kenmore built-in ovens employing identical temperature modulation methods. Reinstallation ensures continued customizable and safe cycle performance.
 

The Simmer Control is an OEM component specifically designed for Bosch ranges. It regulates gas flow to provide the lowest possible flame setting needed for delicate cooking tasks. Precise control allows for uniform, attentive simmering.

Symptoms of a bad simmer control include inconsistent or unadjustable flame heights on low settings. Cracks, damage, or wear of internal mechanisms over time can also cause unstable flame control.

Causes of bad simmer control can be normal wear and tear issues like dirt buildup impeding mechanisms. Accidental impact or overheating leading to cracks are other causes for replacement.

Symptoms of a bad simmer control include:

• Flames that surge or fluctuate below the lowest settings   
• Inability to adjust the flame down sufficiently low
• Burners that shut off or cause overflow flooding on low-heat  

This OEM Bosch part is also compatible with Thermador and some Kenmore ranges. Replace for dependable, Fine-tuned low-heat performance.