Need Help?
Call or text
Illuminates the dryer drum for better visibility when loading and unloading. Replace when bulb burns out or fails to light. Confirm fit with your model.
Originally the dryer was squeaking a lot, so I purchased a new belt tensioner, but the original tensioner was an old-style no wheel tensioner, so that wasn't the source of the squeaking. I saw a lot of lint had built up inside the unit where there shouldn't have been that much. So I viewed a few videos on the Appliance Pros site and saw that the rear wheel guides were the cause of the squeaking and the rear felt drum and blower housing seal needed to be replaced. The rear blower housing was... Read more
Oven won't heat or takes too long to preheat? This igniter generates heat to ignite the bake burner. DIY-friendly repair, typically 20-30 minutes.
Replaced the ignighter and gas safety valve. Have to remove knobs, front panel and grill housing to access these parts. Read more
Replace a broken, cracked, or missing control knob on your cooktop. This dial installs on the control panel to adjust burner settings and temperature.
The knob I ordered from you was well photographed from all angles. I was pretty confident that even if it wasn't the same part it would do the job. I took the old knobs off and placed the new ones on. They were slightly smaller than the original but work great! Read more
Burner won't light or igniter keeps clicking? This cooktop igniter creates the spark to ignite gas burners. DIY repair. Video guide available.
My 18+ year old Jennair cooktop, PN CCG2520W was in need of a rebuild b/c of a welded venturi tube on the right front [RF] burner. In order to remove the glass top cover, you MUST remove the venturi tube. To do this you have to DRILL-OUT the venturi tube which requires a new venturi and orifice holder. The repair was difficult b/c most of the parts are no longer available. But then I found a ray-of-hope. I was able to find some Jennair (Maytag) parts but they are scarce. Later I found... Read more
Rubber feet that attach to the bottom of range grates for stability and surface protection. Replace worn, cracked, or missing grate feet kit.
Bought a Thermador PRSE48" dual fuel range from Craigslist really cheap because it didn't work. Did a little research and decided to overhaul most of the top (gas) end. For what I paid for it it was worth it and I'd have a good stove with new components. Replaced the griddle thermostat, ignition micro switches, ignition re-igniter box, installed fixing kit with 2 new potentiometers, both solenoids, and gas regulator. Had to replace 2 gas lines, all 4 jets, and one brass nut that were... Read more
Oven taking too long to preheat or not heating evenly? Replace the bake element. DIY-friendly repair takes 10-20 minutes with a screwdriver.
It was a very quick repair that took less than 5 minutes to fix. Read more
Burner won't ignite or stay lit? This potentiometer controls gas flow and ignition. Common DIY repair taking 15-30 minutes with basic tools.
After watching a youtube video, I disassembled the front cover on the cooktop (be sure to turn off the power supply). I then switched the potentiometers on two burners. The burner that was not working now worked and the burner that did work did not. Easy to find the culprit....ordered a new potentiometer from here and though I only got regular shipping, it was actually delivered the NEXT DAY! 5 minutes, put in the new part, and all burners work. Great site, thanks for the help! Read more
Oven not heating or preheating slowly? This bake element restores proper baking temperatures. Easy DIY repair—remove door, disconnect wires, swap part.
Found the part number, went to AppliancePartsPros.com and found it within minutes. I ordered the part and it showed up at my house the following day, no special overnight shipping charges. I changed out the element in about 15 minutes. Great experience with AppliancePartsPros.com. Read more
Venturi tube for gas ranges and cooktops. Mixes gas and air for proper burner combustion. Replace if cracked, corroded, or threads are damaged.
Fix oven overheating or E115 error code with this wall oven control board. Regulates temperature and cooking modes. Moderate difficulty, 2-3 hour repair.
Replaced the main control board on a Thermador oven model POD301J/01 after we got an E115 error and the top broiler would come on no matter what setting you put it on and wouldn't turn off and would overheat. Took me about 30 mins total to replace after taking pics to make sure everything went back as it was. So far so good and it's working again! Read more
Secures the igniter to your cooktop for proper alignment and stable ignition. Replace if igniters are loose or spark inconsistently. Confirm fit.
Symptoms: would not light & no gas smell/flow. R&R'd gas solenoid which fixed it. Other parts were in addition to primary inop burner. Read more
Fixes burners that won't ignite or spark continuously. This spark module generates the high-voltage needed for gas ignition. DIY repair, 1-2 hours.
Fix a downdraft vent that won't go up or down, or cycles on its own. This range hood switch controls vent movement. DIY repair in about 1 hour.
I replaced the switch Read more
Brass nut secures the jet holder assembly on gas ranges and cooktops. Replace if stripped, corroded, or damaged during burner maintenance or repair.
First and foremost, don't believe everything you see on Youtube. In order to get to the gas solenoid that feeds the burner you MUST take the entire top off that side of the range. Remove the grates and burner tops. You will see 2x 20mm brass nut, or so it appears, that hold each burner in place on the splash/drip pan. It is not just a nut, it is a venturi that threads down into what is called the jet holder. You may get a socket on it and think you are getting it loose but, more than likely you... Read more
Burner won't light or has no gas flow? This top burner valve controls gas to individual burners. Moderate DIY repair with basic tools needed.
Seals between burner and cooktop surface to prevent gas leaks. Replace if cracked, worn, or causing ignition issues. Verify fit with your model number.
I ordered a replacement gas solenoid valve, which arrived the very next day with only standard shipping! The shipped part was exactly what was needed, and I also ordered 4 replacement O-rings to replace the original dried out ring for each burner base. These parts also arrived within a few days and were the exact parts needed. The service and advice received was commendable. Thanks for the great job. Read more