Thermador Wall Oven Parts

The Bulb is an OEM part for Bosch ovens. This component provides illumination inside the oven, allowing you to easily monitor the cooking process without opening the door and losing heat.

Causes of a bad bulb can include filament burnout due to extended use, electrical issues that cause power surges, or physical damage from accidental impacts. 

Symptoms of a bad bulb include:

• The oven light not turning on
• Flickering light inside the oven
• Dim or uneven lighting
• The bulb appearing visibly damaged or burnt out

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Ignition Device is an OEM part for Bosch gas cooktops. This ignitor is responsible for sparking the burners to safely ignite the gas flow and initiate the cooking process.

The ignition device works through a high-voltage electrical arc that produces a spark near each gas burner valve whenever a cooktop burner is turned on. This spark reliably ignites the gas, allowing full and consistent burner flame.

Causes of a bad ignition device can include defects in the electronic components, wear and tear of the electrode tips over time, or issues preventing a strong enough spark from occurring.

Symptoms of a bad ignition device include:

• Burners that will not light or remain lit
• Repeated lighting attempts required before a flame is produced
• Inconsistent or intermittent ignition between burners
• Burners that light but then extinguish unexpectedly

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This factory fixing kit supplies the OEM hardware required to secure the appliance or designated components during installation or service. Replacing missing or damaged fasteners restores a solid, aligned mount so the unit stays stable without shifting, rattling, or gaps.

• Provides the correct hardware to fasten parts per your model's installation or service instructions
• Replaces stripped, corroded, or missing screws/clips that lead to looseness
• Helps maintain alignment and clearances to prevent gaps, rattles, or vibration
• Typical symptoms: loose mounting, panels that shift, or movement when opening/closing doors or drawers

• Disconnect power; shut off water or gas if applicable before starting work
• Follow the model-specific installation/service manual for attachment points and sequence; use the proper driver bit and do not overtighten
• Verify the unit is level and securely anchored; check clearances and operation after securing

This Bake Element is an OEM part for Bosch Ovens. It's responsible for providing heat in the oven cavity for baking and cooking purposes. With prolonged use, the bake element can wear out or malfunction.

Frequent use at high temperatures can cause the bake element to deteriorate over time. Physical damage or overheating may also contribute to its failure.

Symptoms of a Bad Bake Element:

• Uneven cooking or baking
• Inconsistent oven temperatures
• Oven takes longer to preheat

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The oven door gasket is the heat-resistant seal around the 30-inch oven cavity. It helps the oven reach and hold temperature, preventing heat and steam leaks, and replaces a worn or damaged seal for consistent baking results.

• Seals the door-to-cavity gap to limit heat and moisture loss
• Restores proper door compression to help maintain accurate temperatures and normal preheat times
• Replaces gaskets that are torn, frayed, flattened, brittle, or stretched
• Common symptoms: hot air or steam escaping at door edges, temperature fluctuations, longer cook times, or a door that no longer closes snugly

• Disconnect power and allow the oven to cool completely before servicing
• Open the door and remove the old gasket, noting seam orientation and where the ends seat
• Clean the mating surfaces; install the new gasket with the seam at the bottom center, seating the ends fully into the factory holes/retainers without overstretching
• Close the door and check for uniform contact around the perimeter

Note: Kit includes 4 feet and a tube of RTV with instructions.

This door seal restores a tight barrier between the oven door and cavity. Replacing a worn gasket helps your oven reach and hold temperature, reduces heat escaping at the door edges, and supports more consistent baking and roasting results.

• Creates a heat-resistant seal around the oven opening
• Helps the oven preheat and maintain set temperature
• Limits heat, steam, and odors from escaping at the door
• Typical signs it needs replacement: visible tears or flattening, heat felt around the door, longer preheat/cook times, or uneven baking

• Disconnect power at the breaker and let the oven cool completely
• Open the door, pull the old seal from its channel, and clean the groove
• Press the new seal evenly into the channel without stretching; ensure corners seat fully
• Close the door to verify uniform contact all around and adjust as needed

This Bake Element is an OEM part for Bosch ranges. It serves a role in generating heat for baking and cooking in the main oven cavity. Over time, continuous use and high temperatures can cause the bake element to wear out or fail.

Repeated heating and cooling cycles can lead to the bake element's deterioration. Physical damage or exposure to excessive heat can also cause it to malfunction.

Symptoms of a Bad Bake Element:

• Inconsistent oven heating
• Uneven cooking or baking
• Oven not reaching set temperatures

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Bake Element is an OEM part for Bosch ranges and ovens. It generates heat through calibrated heating coils, which bathe the oven cavity in consistent warmth for thorough yet delicate cooking. 

Causes of failure can be things like normal wear over time compromising insulation or shorting coils. Periodic replacement preserves cooking capacity.

Symptoms of a bad bake element include:

• Temperature fluctuations during use
• Inability to maintain set baking temperatures
• Oven display errors or failure to heat altogether
• Discoloration, cracking or other visible signs of damage on coils

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Fan is an OEM component specifically designed for select Bosch built-in ovens. As a critical convection element, it circulates internal air currents for optimal heat distribution throughout baking and broiling cycles.

Powerful yet precisely balanced centrifugal motion agitates spacious oven cavities with homogeneous warmth. Aerodynamic fan blades expedite even cooking without hot or cold spots. 

Causes requiring replacement relate to bearing seizure or broken blade attachments disrupting designed circulation. Prolonged heat exposure may cause premature motor failure or cracked housings to no longer sustain needed speeds.

Symptoms signaling the need for a new fan include:

• Inability to effectively circulate air for simultaneous multi-rack cooking  
• Louder than average operation noise accompanied by vibration
• Erratic or ineffective temperature management within cycles

This OEM Bosch replacement fan is also compatible with Thermador, Gaggenau, and some Kenmore built-in ovens employing convection methods. Proper reinstallation restores designed air transfer capabilities for perfect results.
 

This is a replacement glass panel for the appliance's front panel. It restores a clean, durable surface and helps protect the components behind it when the original glass is cracked, chipped, or shattered.

• Forms the exterior glass surface on the appliance's front panel
• Helps shield underlying components from spills and impacts
• Restores proper fit and appearance when the original glass is damaged
• Common symptoms: visible cracks/chips, shattered glass, loose or rattling panel, missing glass

• Disconnect power; also shut off gas before servicing
• Wear cut-resistant gloves and eye protection; handle glass carefully
• Support the door or front panel during removal to prevent stress or drops
• Transfer and reuse existing trim, logos, gaskets, and hardware as designed; do not overtighten fasteners

This spark igniter is the burner electrode that creates the high-voltage spark to light the gas. Replacing a worn igniter restores quick, reliable ignition and helps eliminate repeated clicking or having to light the burner manually.

• Generates a spark at the burner to ignite gas during lighting
• Typical symptoms: burner won't light, no visible spark at that burner, intermittent or delayed ignition, or needing a match to light
• Replaces a cracked, fouled, or heat-damaged electrode that no longer sparks reliably
• Provides the ignition spark only; gas flow is managed by the valve

• Disconnect power and shut off gas before servicing
• Remove grates/caps and access the burner; note wire routing and mounting
• Transfer mounting hardware from the old igniter; handle the ceramic insulator gently and keep the tip clean
• Reassemble, restore power/gas, and verify proper spark and burner ignition

This potentiometer is the rotary sensor behind the control knob. It converts knob rotation into an electrical signal the control board uses to adjust settings, restoring smooth, accurate response when a worn or erratic control causes inconsistent operation.

• Translates knob rotation into a variable-resistance signal for the electronic control
• Enables the control board to regulate power/heat or speed, depending on model
• Common failure symptoms: unresponsive or jumpy settings, dead spots when turning, or settings that drift
• Helps restore precise, repeatable adjustments at the knob

• Disconnect power to the appliance before servicing
• Pull off the knob and open the control panel to access the potentiometer
• Move wires one at a time to the new part; align the shaft/flat to the knob as noted
• Reassemble and test full range of adjustment; follow any model-specific calibration if required

This OEM part is a power control board. The power control board provides power to the electronic oven control board. If the oven is no longer turning on, or the digital display is no longer visible, this could mean it's time to replace the power control board. Luckily this is a relatively simple process.To begin, make sure to turn off the power to the oven by unplugging it or shutting off the circuit breaker. Then proceed to remove the upper back panel. Once removed locate the power control board and remove the wire harness and wires attached to it. Be sure to take note of the orientation of the wires to place them into the correct terminals on the new board. Attach the wires to the new board and snap the new board back in place. Resecure the back panel and put the oven back in place.This genuine replacement part is sold individually and is compatible with Bosch, Thermador, and Gaggenau ovens.

This condenser fan blade mounts to the fan motor and pulls air across the condenser coil and compressor. Replacing a cracked or warped blade restores airflow so your refrigerator cools efficiently and the compressor runs at a safe temperature.

• Circulates air through the condenser coil and over the compressor to remove heat
• Helps maintain cooling performance and stable system pressures
• Common symptoms: weak or no airflow at the rear/base, rattling or scraping noises, wobble/vibration, visible cracks or missing fins, warmer-than-normal compartments or hot cabinet sides
• Works with the condenser fan motor and shroud; typically replaced when the hub is stripped or the blade is damaged

• Disconnect power and pull the refrigerator out; remove the rear access cover near the compressor
• Note blade orientation and depth on the motor shaft before removal
• Pull the old blade straight off; press the new blade onto the shaft until fully seated and ensure it spins freely with proper shroud clearance
• Reinstall the cover, restore power, and verify strong, quiet airflow

Color: metallic. Measures about 13-1/2 inches wide by 5 inches high.

The Grease Filter is an OEM part for Bosch ranges and cooktops. It is responsible for capturing and containing grease, oils, and other vapors produced from cooking to help keep indoor air fresh and prevent buildup. Regular cleaning is important to maintain optimal performance.

Causes of a bad grease filter can include excess buildup that blocks airflow from frequent high-heat cooking. Exposure to flames or excessive heat may cause damage over time as well.

Symptoms of a bad grease filter include:

• Reduced suction power and airflow from the range hood
• Grease accumulation on surrounding surfaces below the hood
• Unpleasant cooking odors escaping into the kitchen rather than being vented outside

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.