Thermador Wall Oven Parts

Replacement bake element for the oven that restores heating for even baking and proper temperature performance. Installs in the oven cavity to provide the heat required during bake cycles. What it does:

• Heats the oven cavity during bake cycles so food cooks evenly.
• Common symptom: oven fails to reach set temperature or food is undercooked.
• Visible symptom: element that is blistered, broken, or shows burn marks may need replacement.
• Electrical symptom: an open (no continuity) element will prevent the oven from heating.

• Always disconnect power to the appliance at the breaker before starting work.
• Allow the oven to cool completely and wear gloves to protect against sharp edges.
• Access typically requires removing oven racks and the inner panel; disconnect wiring at the element terminals and secure the new element in place.
• Restore power and test the oven on a bake cycle after installation.

Knob, blk (cvs)

The Control Knob is an OEM part for Bosch ranges and cooktops. As the interface regulating gas flow, control knobs activate precise burner levels through internal calibration.

Causes of failure include loosened set screws beneath allowing knob slippage. Prolonged heat and moisture exposure may also degrade contact surfaces over time.

Symptoms of faulty knobs include:

• Burners failing to engage or not matching dial settings
• Inability to decrease output levels from full flame
• Knobs wobbling insecurely or detaching entirely

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Restore fast, even convection cooking with this rear convection heating element. It supplies a ring of heat around the fan at the back of the oven so temperatures rise and hold properly in convection bake and roast modes.

• Provides heat around the convection fan for uniform air circulation and even results
• Common symptoms: no heat or very slow preheat in convection modes
• Fan runs but temperature does not rise in convection
• Visible damage or a break in the element

• Disconnect power at the breaker or unplug the appliance; allow the oven to cool completely.
• Remove racks; access and remove the element's mounting screws from inside the oven (procedure varies by model).
• Pull the element forward carefully; label and transfer wires one at a time so they don't slip back into the cavity.
• Reuse existing hardware; ensure terminals are tight, reassemble, and test a convection cycle.

This gas pressure regulator controls and stabilizes incoming supply pressure to the appliance manifold, helping ensure consistent burner flames and reliable ignition. Replace if the original regulator is sticking or no longer maintaining correct pressure.

• Regulates incoming gas to the appliance's rated manifold pressure
• Helps maintain even flame height and proper combustion
• Supports reliable burner ignition and reduces flame-out from pressure swings
• Common symptoms include weak or uneven flames, yellow tipping, burners not lighting or not staying lit, or flames that are too high

• Disconnect electrical power and shut off the gas supply before servicing
• Observe the flow-direction arrow; install with outlet toward the appliance manifold
• Use approved gas-rated thread sealant on male threads only and leak-test all joints with a non-corrosive solution after installation

The Oven Door Gasket Kit is an OEM replacement part for 27" Bosch wall ovens. It includes a gasket for insulating the oven cavity while in use and clips to secure it. Over time, heat and compression can break down gasket material allowing potential leaks of hot air from the oven during cooking or difficulty closing the door. Causes involve standard wear from repetitive door closing as well as exposure to high oven temperatures over many heating cycles.

Symptoms of failed gaskets include: 

• excessive heat escape from the door opening
• Door locking difficulties
• visible cracks or tears in the gasket materials 

Replacing the gasket allows for smooth door movement and an tight seal when closed. This Bosch part can also be used on Thermador and Gaggenau appliances.

This Thermal Fuse is an OEM part for Bosch Wall Ovens. It acts as a safety mechanism, designed to interrupt the electrical connection if the oven's temperature exceeds the safe limit.

What Causes a Bad Thermal Fuse:
Overheating due to issues like a malfunctioning thermostat or restricted airflow can cause the thermal fuse to blow. This interruption prevents the oven from operating at dangerously high temperatures, reducing the risk of fire.

Symptoms of a Bad Thermal Fuse:

• Oven fails to heat up
• No response or display on the control panel
• The oven doesn't maintain the set temperature

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This door switch detects when the door is fully closed and latched. Replacing a worn or stuck switch restores safe, consistent start/stop behavior and ensures the unit only runs with the door securely shut. What it does:

• Senses door position and signals the control to enable/disable operation
• Prevents the appliance from running with the door open
• Resolves issues such as: won't start despite power, stops when the door is jostled, "close door" message, or needing to press on the door to run
• Helps restore reliable cycle start and proper safety interlock function

• 1 door switch

• Disconnect power at the breaker before servicing
• Access the switch behind the door panel or latch area; note wire locations or take a photo
• Move wire connectors to the new switch one at a time; ensure terminals are fully seated
• Reassemble and test door closure and operation before returning to service

This replacement roller fits the front or rear position of a slide mechanism, restoring smooth, even movement and reducing noise when a wheel is worn or broken. It helps racks or drawers glide properly and stay aligned. What it does:

• Provides low-friction rolling support for the slide track
• Helps slide-out assemblies move freely without binding or scraping
• Worn or damaged rollers can cause sticking, squeaking, or uneven travel
• Restores proper alignment and smooth operation when replaced

• 1 roller assembly

• Disconnect power and allow the appliance to cool before servicing
• Remove the slide-out assembly; note roller orientation and hardware
• Transfer/reuse existing screws, clips, or retainers as required
• Do not lubricate unless the manufacturer specifies a lubricant

This grate foot assembly installs on the underside of a gas cooktop or range grate to cushion and stabilize it. Replacing worn or missing feet helps protect the surface and keeps cookware level while you cook.

• Cushions contact between the grate and cooktop surface
• Helps keep the grate from sliding and reduces rattling
• Maintains proper grate height for stable, level cookware
• Common symptoms: wobbling/rocking grate, missing or hardened feet, scratches on the surface

• Allow the cooktop and grates to cool completely before servicing
• Remove the grate, pull off the old foot, and clean the mounting area
• Press the new foot firmly into place; if your model uses an adhesive or retainer, follow the manufacturer's cure time before using the burners
• For best results, replace all feet on a grate at the same time and it sits flat

A replacement high-temperature cut-out that helps protect ovens by interrupting power if internal temperatures rise above safe levels. Restores the appliance's over-temperature protection so heating elements can be safely shut off when needed. What it does:

• Monitors oven temperature and opens the circuit if temperatures exceed a safe threshold to prevent overheating.
• Stops power to heating elements when tripped, preventing further temperature rise.
• Common symptoms of a failing cut-out: oven won't heat, continuous heating or no control over temperature, or oven shuts off unexpectedly.
• Used as a safety device in the oven's temperature-control system.

• Disconnect power at the breaker and allow the appliance to cool completely before servicing.
• Replace with the exact OEM cut-out and secure all wiring connections.

Electrode that produces the ignition spark for gas ovens and ranges, restoring reliable burner lighting. Replace a damaged or worn electrode to stop repeated clicking, weak sparks, or burners that fail to light. What it does:

• Delivers the spark at the burner to ignite gas during startup.
• Common symptom fix: oven/range burners that won't light or that click continuously without producing a flame.
• Use when the electrode is cracked, corroded, or the ceramic insulator is damaged.
• Works as part of the appliance's ignition system alongside the spark module/igniter wiring.

• Turn off power and gas supply before beginning any service.
• Avoid touching or chipping the ceramic insulator; handle the tip carefully.
• Reconnect wiring exactly as removed and secure the electrode in the original orientation.

This is a replacement control knob that restores safe, easy control of a cooktop or oven function. It provides a secure grip and clear position indication so you can set heat or cycle settings precisely. What it does:

• Fits over the control shaft to allow turning temperature/settings without touching the control stem
• Replaces cracked, stripped, missing, or hard-to-turn knobs
• Restores clear detent positions for accurate setting selection
• Helps prevent accidental changes by seating securely on the shaft

• Before servicing, disconnect power to the appliance and shut off gas supply if applicable
• Pull old knob straight off the control shaft; align replacement onto the shaft and push until fully seated
• Do not use excessive force; inspect the control stem for damage before installation

This ignition device creates the spark that lights gas burners and oven burners, restoring reliable ignition for gas ranges. It's the direct replacement component that produces the high-voltage spark used at the electrodes. What it does:

• Generates the spark needed to ignite gas at burners and oven igniters.
• Fires when the control calls for ignition; no spark often indicates a failed module.
• Common symptoms: continuous clicking with no ignition, burners that won't light, or intermittent sparking.
• Works with the range/oven ignition circuit to sequence spark to the electrodes.

• Always shut off electrical power and gas supply before starting work.
• Handle electrode wires and ceramic insulators carefully to avoid damage.
• Verify correct wiring and secure mounting; test ignition function after restoring power and gas.

Note: Size 8 inches

The Element is an OEM replacement part for Bosch electric ranges. It generates the heat needed for baking, broiling, and other cooking functions.

Causes of a bad element can include mineral buildup interfering with heat transfer, melted or burnt connectors from overheating, or damage from impact over time. 

Symptoms of a bad element include:  

• Inconsistent or incomplete heating of the appliance
• Long preheat times or inability to reach desired temperature  
• Burned food indicating insufficient or uneven heat
• Safety issues such as sparking or smell of burning

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This door opening lever is the replacement release lever that lets the appliance door latch open and close smoothly, restoring reliable door-opening action and making everyday use easier. What it does:

• Replaces a worn, broken, or cracked lever that releases the door latch.
• Lets the door latch release properly so the door opens without excessive force or sticking.
• Works with the latch assembly to help ensure the door closes securely and operates smoothly.
• Addresses common symptoms such as a loose or unresponsive door handle, difficulty opening the door, or a lever that snaps.

• Disconnect power (and water, if applicable) before attempting any repair.
• Access may require removing the door trim or outer panel; basic hand tools are typically needed.
• Inspect surrounding latch components while replacing the lever and replace any damaged hardware.

A replacement selector knob that lets you turn and choose appliance settings smoothly and safely. Restores a damaged, loose, or missing control knob so you can change cycles and temperatures with confidence. What it does:

• Fits onto the control shaft to select functions, cycles, or heat levels
• Replaces cracked, stripped, or worn knobs that won't stay set or slip during use
• Stops erratic control feel and restores a positive detent or indexed rotation
• Works with the matching control shaft shape

• Disconnect power to the appliance before servicing
• Align the knob splines with the control shaft and push straight on until fully seated
• If knob is stiff, check for debris on the shaft; do not force or hammer the knob into place