Thermador Wall Oven Parts

This replacement fan restores proper airflow inside your appliance, circulating air for cooling and overall performance. Replacing a worn or damaged fan helps keep temperatures in check and reduces noise from rubbing or imbalanced blades.

• Circulates air as designed to cool components and move heat/moisture where intended
• Common symptoms of a failing fan include loud scraping or rattling, weak or no airflow, wobble, or the fan not turning
• Heat buildup around the control area or repeated thermal shutdowns can point to a fan issue
• Physical cracks, broken fins, or warping indicate the fan should be replaced

• Disconnect power at the breaker; allow the unit to cool completely
• Access the fan per your model; remove panels/guards carefully and note orientation
• Transfer any retaining nut/clip or gasket from the original as required; seat the fan fully and secure
• Spin by hand to verify free movement; ensure no contact with shrouds before restoring power

This ignition device generates the spark needed to light gas burners, restoring reliable ignition and preventing continuous clicking or no-light conditions. Replace a failed module to re-establish normal burner ignition. What it does:

• Sends high-voltage sparks to the burner electrodes to ignite the gas flame
• Replaces a faulty spark generator when burners won't light or there is no visible spark
• Stops continuous clicking or rapid sparking caused by a failing ignition module
• Works as the central control for timed spark output to each burner electrode

• Disconnect electrical power and shut off the gas supply before starting any work
• Remove the oven/range access panel and note wire locations or take a photo to ensure correct reconnection
• Handle the electrode and module carefully to avoid bending or contaminating the spark tip

The Surface Element is an OEM part for Bosch cooktop and ranges. Measuring 6 inches across, it provides focused heat from below for smaller sized cookware.

Causes of a bad 6" plug-in element generally relate to normal wear and tear over time. Spills left on the coils could potentially cause issues by corroding internal wiring or damaging heating components.

Symptoms of a bad narrow surface element can include:

• The element heating intermittently or not at all
• Only parts of the coil visibly heating up
• Buzzing or clicking coming from below the element
• Tripped circuit breakers affecting that specific element

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Surface Element (240V-2100W) is an OEM part for Bosch cooktops and ranges. It provides consistent, even heating from below pans on the cooktop surface.

Causes of a bad surface element can include normal wear and damage from extended, heavy usage. Food or liquid spills left on the element for prolonged periods could potentially corrode the coils or electronics over time as well.

Symptoms of a bad surface element include:

• Element not heating up at all or heating unevenly
• Element heating intermittently or stopping prematurely
• Buzzing, clicking or smoke coming from below the element
• Tripped or blown circuit breakers when using that element

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

A replacement glass turntable plate that restores a microwave's rotating cooking surface for even heating and stable cookware support. Fits on the drive roller to provide a flat, heat-safe surface for daily microwave use. What it does:

• Replaces a cracked, chipped or missing glass turntable so food heats more evenly
• Provides a stable surface for plates and bowls to rotate during cooking
• Works with the turntable roller and coupling to restore proper rotation
• Prevents wobble and scraping that can occur with damaged glass

• Unplug the microwave or disconnect power before installing
• Handle the glass carefully to avoid cuts; do not install if chipped or cracked
• Align plate on the center drive coupling/roller support; it seats and rotates freely
• Use only the exact OEM plate size and part number to ensure proper fit

This control knob replaces a worn, broken, or missing stove/oven knob to restore safe, reliable control and improve the appliance's appearance. It fits directly onto the control shaft for a secure, tactile grip. What it does

• Replaces a damaged or missing control knob so you can set burners or oven functions accurately
• Provides a solid grip and clear pointer for selecting settings
• Stops slipping or spinning caused by a cracked or worn knob
• Helps restore normal operation when the original knob is loose or won't stay engaged

• Disconnect power (unplug appliance or switch off breaker) before servicing to avoid electrical or burn hazards.
• Pull the old knob straight off the control shaft; no special tools typically required.
• Align the new knob's splines with the shaft and push straight on until fully seated.
• Do not force the knob; if it does not fit, check shaft shape and orientation before applying pressure.

The Pressure Regulator is an OEM replacement part for Bosch gas cooktops. It maintains consistent burner flame levels for precise meal preparation, maximizing fuel efficiency. Even pressure safeguards safety through controlled gas flow.

Causes of a bad pressure regulator can include deteriorating diaphragm seals or valve shafts due to repetitive operations over the appliance's lifespan. Mineral scales from sediment in gas lines threaten integrity.

Symptoms of a bad pressure regulator include:

• Flames lift or flare away from burner heads unpredictably   
• Burners cannot maintain set heat levels, constantly cycling 
• Difficulty achieving desired flame height or cooktop shuts off
• Potential safety hazards like uncontrolled gas leakage

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This diode is a small rectifier used on the appliance control electronics to allow current to flow in one direction, protecting the board and enabling proper control signals. Replacing a failed diode restores correct circuit behavior. What it does:

• Provides one-way current flow on the control board to prevent reverse voltage
• Protects sensitive electronics from backfeed and voltage spikes
• Can prevent control errors caused by a shorted or open diode
• Commonly replaced when control circuits fail to power or behave intermittently

• Disconnect power to the appliance before accessing controls to avoid shock
• Handle circuit boards and components with ESD care; avoid touching traces and contacts

This tubular bake element is the lower heating element for electric ovens, restoring oven bake heat and even cooking performance. It replaces a damaged or non-heating element to get your oven back to regular baking temperature. What it does:

• Produces the primary radiant heat from the bottom of the oven for baking and roasting
• Common symptom: oven won't reach or hold set bake temperature
• Common symptom: visible breaks, blistering, or arcing on the element surface
• Common symptom: uneven baking or loss of heat from the bottom of the cavity

• One bake (lower) element

• Disconnect power at the breaker or unplug the range before any work
• Access typically requires removing the oven floor or lower access panel and unscrewing the element terminals
• Inspect wiring and terminal connections for heat damage; replace or repair as needed

This transformer provides the low-voltage power supply required by the appliance control system, enabling proper operation of the control board and related low-voltage circuits. Replaces a failed or noisy transformer to restore reliable control power. What it does:

• Steps down mains voltage to the appliance's low-voltage control circuit for the control board and relays
• Helps restore control functions when a failed transformer causes no power, intermittent control operation, or unresponsive electronics
• Prevents control-board brownouts by providing consistent low-voltage feed (when the transformer itself is the issue)
• Used wherever a dedicated appliance control transformer is required by the appliance's electrical system

• One replacement transformer

• Always disconnect power to the appliance before accessing electrical components
• Verify wiring locations and terminal IDs before removing the old transformer; label wires if needed
• Transfer mounting hardware and brackets from the old part unless new hardware is explicitly included

This latch knob kit replaces a broken or worn dishwasher door latch knob to restore secure door operation and a finished appearance. It installs at the front of the dishwasher door to engage the latch assembly. What it does:

• Replaces a damaged or cracked door latch knob so the door can be closed and latched properly
• Restores a secure grip for opening and closing the dishwasher door
• Helps eliminate rattling or improper door engagement caused by a missing or loose knob
• Matches white trim and visible door components for a clean finish

• Disconnect power to the appliance before starting any repair
• Removal of the inner door panel or trim may be required; follow the steps
• Handle small parts carefully and keep fasteners organized during reassembly