Thermador Wall Oven Parts

The Ignition Device is an OEM part for Bosch ranges and ovens. Located near each gas burner, the ignition device provides the critical spark needed to light the burners during startup. 

Causes of a bad ignition device can include wear from prolonged use over many years. Mineral buildup or debris accumulation may also prevent the spark from jumping across.

Symptoms of a bad ignition device include:

• Burners failing to light or staying lit
• Repeated attempts needed to ignite the gas  
• Inconsistent flame heights or burner performance
• Fault codes or error messages displayed

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models. 

This inner door glass panel replaces the interior glass pane in the door assembly. It restores a clear, heat-resistant barrier so your appliance can retain heat and operate safely after the original pane cracks or shatters.

• Serves as the interior glass pane of the door facing the cavity
• Helps insulate the cavity to maintain stable cooking temperatures
• Direct replacement for cracked, shattered, or missing inner glass
• Can help address heat loss and unsafe door conditions

• Disconnect power at the breaker and allow the appliance to cool completely before starting
• Remove the door per your model's service instructions and place it on a padded work surface
• Wear cut-resistant gloves and eye protection; handle glass by the edges
• Transfer any brackets/clips in the original order and tighten fasteners snugly without overtightening

This Broil Heating Element is an OEM part for Bosch Ranges. It is responsible for providing high heat for broiling functions and evenly distributing heat within the oven cavity. It ensures efficient broiling performance for cooking various dishes.

A common issue with a malfunctioning Broil Heating Element is wear and tear over time, leading to potential element damage or failure. Frequent usage, or heating irregularities can compromise its function.

Symptoms of a defective Broil Heating Element may include:

• Uneven broiling or cooking results
• Inadequate heating or failure to reach desired temperatures
• Visible damage or signs of wear on the heating element

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

Restore confident control of your appliance with this replacement control knob. It slides onto the control shaft to provide a secure, accurate grip so you can easily select settings when the original knob is cracked, stripped, or missing. What it does:

• Attaches to the control shaft to select temperature, cycle, or power settings
• Restores positive engagement and smooth turning of the control
• Helps resolve a loose, wobbly, or slipping selector
• Replaces knobs that are cracked, broken, or won't stay on

• One control knob

• Disconnect power; for gas appliances, also shut off the gas supply before servicing
• Pull the old knob straight off the shaft; if your model uses a set screw or clip, loosen/remove it first
• Align the new knob with the shaft and press on firmly; retighten any set screw if present
• Test operation to ensure the knob engages and turns the control smoothly

This wire oven rack slides into the oven's side supports to hold cookware at the correct height. Replace a bent, rusted, or missing rack to restore safe, level support and smooth sliding for baking, roasting, and broiling. What it does:

• Provides a stable, level surface for pans and dishes on the oven's side rails
• Lets you position food at multiple heights for proper cooking and airflow
• Slides in and out for easy loading and unloading when properly seated
• Common replacement reasons: bent/warped wires, flaking finish or rust, rough sliding, or poor fit

• 1 oven rack

• Allow the oven to cool completely; wear gloves to avoid sharp edges
• Pull the old rack straight out; clear debris from the side rails
• Align the new rack with the side supports and slide it in; ensure stops face the back if present
• Ensure the rack is evenly seated on both rails before placing cookware

Heating element assembly that restores your appliance's ability to heat water or air so cycles reach the correct operating temperature. Use it to replace a failed heater that prevents proper drying, sanitizing, or heating performance. What it does:

• Heats water or air during operation so wash, sanitize, and dry cycles reach the intended temperature.
• Common repair for no-heat, poor drying, or cycles that fail to reach or maintain temperature.
• Works with the appliance's control and thermal cutoff to deliver regulated heat when called for.
• Replace if the element is visibly damaged, shows an open circuit on a multimeter, or triggers thermal faults.

• Always disconnect power (unplug or switch off breaker) before servicing the appliance.
• Handle carefully; terminals and mounting brackets can be sharp or fragile. Avoid bending element tubing.
• After installation, restore power and run a short diagnostic or cycle to confirm proper heating and no error codes.

This catalyst is a dishwasher replacement component that helps maintain cleaning performance by promoting proper detergent action during the wash cycle. Use when cleaning results decline or persistent film/spotting appears after runs. What it does:

• Promotes the chemical action of detergent for more effective soil removal
• Helps reduce cloudy film, spots, and residue left on dishes
• Works as part of the dishwasher's wash system to support normal cleaning cycles
• Fits into the appliance at the factory-designated location and interfaces with existing components

• Disconnect power (and water supply if required) before starting service
• Handle part carefully and reinstall using the original mounting hardware
• Do not modify the part; use only as designed to ensure proper function

This is a replacement nut used to secure internal appliance components. It restores proper fastening so assemblies stay tight and reduces noise or movement caused by loose hardware. What it does:

• Secures brackets, trim or internal components to prevent parts from shifting
• Stops rattling or vibration caused by a missing or loose nut
• Restores proper fastening after maintenance or repair
• Helps maintain correct alignment of the secured component

• Disconnect power and water before accessing internal parts
• Use appropriate hand tools and a firm grip; avoid power tools that can over-torque
• Do not overtighten — snug until secure to avoid stripping threads
• Replace any corroded or damaged mating hardware for a lasting repair

This is a replacement electrical fuse used in select Bosch appliances to protect internal circuits by opening the circuit if an overload or fault occurs. It restores proper safety protection when the original fuse is blown. What it does

• Acts as an overcurrent/thermal protection element for control and power circuits
• Prevents further electrical damage by interrupting power when a fault is present
• Common symptom of a blown fuse: appliance has no power or certain functions won't operate
• May be checked when the appliance is completely unresponsive or specific components do not receive power

• One replacement Fuse 4 (mdl 4)

• Disconnect power to the appliance before inspecting or replacing the fuse
• Replace only with the exact part specified for your model; do not bypass the fuse
• If the replacement fuse blows again, stop use—repeated failures indicate a deeper electrical problem
• Wear appropriate safety gear and follow for access instructions