Parts for Maytag MGDX655DW2: 02 - Top And Console Parts

Replacement control knob for dryer control panel. Restores tactile selection of heat, cycle, and temperature settings. Replaces cracked, missing, or worn knobs.

This is the push-to-start relay switch that engages the dryer motor when the start button is pressed. It also controls the end-of-cycle buzzer signal. Replace this relay if the dryer does not start when you push the start button, if the buzzer no longer sounds at the end of a cycle, or if the switch feels stuck or unresponsive.

Fix a dryer that won't start or stop properly with this switch. Common solution for unresponsive controls. Straightforward repair for most models.

Dryer stops early on auto cycle but works on timed? The moisture sensor control board monitors dryness levels. DIY-friendly repair, 15-20 minutes.

This rear panel replaces the dryer's back bulkhead to restore the appliance's structural enclosure and help protect internal components from dust and debris. It provides a clean mounting surface for internal parts and improves cabinet integrity. What it does:

• Replaces a damaged, dented, or corroded rear cabinet panel
• Protects internal wiring, ducts, and components from external debris
• Restores proper mounting surfaces for internal assemblies and fasteners
• Helps maintain correct airflow paths by sealing the dryer cabinet

• One rear panel/back bulkhead

• Disconnect power (and gas if applicable) before beginning any repair
• Installation typically requires removing the dryer cabinet and several fasteners; keep hardware for reuse unless damaged
• Inspect and replace any worn gaskets, seals, or mounting clips while cabinet is open

The Console Clip is an OEM part compatible with Whirlpool dryers. This clip secures the control console assembly to the top panel, ensuring it is firmly mounted during operation. Properly functioning clips are necessary to maintain the correct alignment of controls and prevent detachment. 

Causes of a bad clip can include wear and fatigue from repeated opening and closing of the dryer door. Excessive force or impact could also bend or break the clip over time.

Symptoms of a bad clip include:

• Loose console assembly that is not securely fastened  
• Misaligned or dangling controls that do not sit flush
• Dislodged console at risk of detaching from housing
• Missing clip leaving an open mounting point

This OEM Whirlpool replacement clip is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Replacement screw secures panels, brackets, and internal assemblies. Needed when original hardware is stripped, corroded, or missing to keep parts tight.

Replacement lint screen that traps debris to prevent clogs and maintain airflow. Replace when damaged, torn, or not sealing properly. Confirm fit with your model.

Type AB #8-18 x 5/8 inch thread-forming screw secures panels and components in appliances. Replace missing, stripped, or corroded fasteners.

The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.

This part fixes the following symptoms:

• Loose or wobbly components within the appliance
• Panels or parts that are not securely attached
• Rattling or unusual noises due to loose parts
• Damaged or missing screw

The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Replacement top panel for dryers and laundry centers. Restores the upper surface when the original is cracked, dented, warped, or damaged.

Replacement mounting nut secures panels, brackets, and studs in dryers. Restores tight fit for worn, stripped, or missing fastening hardware.

Dryer won't start when you press the button? This push to start switch initiates the motor and heating element. Simple 5-minute DIY replacement.

Fix unresponsive buttons or blank displays with this dryer control panel. Restores complete cycle selection and settings control for your appliance.

Fix a dryer that won't shut off or has a timer that won't advance. This timer control manages cycle duration. Moderate DIY difficulty, 30-45 minutes.

This is a cycle selector switch located on the dryer's control panel that allows you to choose between different drying cycles and settings. It connects to the timer and control circuitry to route power to the correct cycle. Replace this switch if the dryer does not respond when you turn the cycle knob, only works on certain settings, or if the switch feels loose or fails to click into position.

Replacement name plate that restores your appliance's identification label. Needed when the original plate is faded, damaged, or missing.