Parts for Maytag MGDX700AG0: 01 - Top And Console Parts

Secures control knobs to the panel on washers and dryers. Replace if the clip is broken, missing, or worn, causing knobs to fall off or sit loose.

Positions and secures dryer components with proper alignment and clearance. Replace if cracked, broken, or missing to restore stable spacing between panels.

This plated control knob replaces a worn or missing knob on your range or cooktop, restoring smooth burner adjustment and a matching look. It pushes onto the existing control stem and operates like the original. What it does:

• Mounts on the burner control stem to set and adjust heat levels
• Replaces cracked, stripped, loose, or missing knobs to restore proper control
• Provides clear pointer orientation for consistent settings
• Symptoms it can help with: knob falls off, wobbly/loose feel, hard to turn, won't engage

• One plated control knob assembly

• Disconnect power and let the cooking surface cool; if applicable, turn off gas supply.
• Pull the old knob straight off the stem—avoid prying or side pressure that can damage the shaft.
• Align the new knob with the stem and press straight on until fully seated.
• Test the control for smooth operation before regular use.

This replacement bezel restores the control panel trim for a smooth, finished look and helps protect the console area from spills and wear. It's a direct-fit cosmetic and protective piece for the appliance control area. What it does:

• Covers and protects the control panel surface and underlying components from spills and damage
• Provides the finished trim that secures buttons, dials, or the display area
• Replaces cracked, warped, or cosmetically damaged trim that can catch debris or impede controls
• Helps keep the control area sealed and easier to clean

• Disconnect power to the appliance before starting any repairs to avoid shock or injury
• Typical installation requires removing a few screws or clips on the control console; keep fasteners for reassembly
• Handle painted or plastic surfaces carefully to avoid scratching; use a soft, non-marring tool to pry clips if needed

Replacement mounting screw for securing appliance panels, trim, and internal components. Restores proper fastening when original screws are missing or stripped.

The Console Clip is an OEM part compatible with Whirlpool dryers. This clip secures the control console assembly to the top panel, ensuring it is firmly mounted during operation. Properly functioning clips are necessary to maintain the correct alignment of controls and prevent detachment. 

Causes of a bad clip can include wear and fatigue from repeated opening and closing of the dryer door. Excessive force or impact could also bend or break the clip over time.

Symptoms of a bad clip include:

• Loose console assembly that is not securely fastened  
• Misaligned or dangling controls that do not sit flush
• Dislodged console at risk of detaching from housing
• Missing clip leaving an open mounting point

This OEM Whirlpool replacement clip is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Dryer won't respond to buttons or display shows no information? This electronic control board assembly restores cycle selection and display functionality.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear panel onto the cabinet frame, ensuring a sturdy connection between housing components.  Proper installation is critical for the washer's structural integrity.

Causes of a bad screw include corrosion from repeated water exposure or stresses from years of use. Loosening can occur from vibrations weakening the threads over time. 

Symptoms of a bad screw include:

• Rear panel detaching from frame opening gaps
• Increased noise and vibrations from a compromised seal  
• Stress on other connections from improper mounting points
• Potential leak paths from openings near hoses or tub areas

This OEM Whirlpool replacement screw helps maintain a tight panel closure. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Rear panel for dryers. Replaces cracked, damaged, or missing back panels. Covers the rear housing and provides structural support for the cabinet.

Drum support plug for dryers. Installs inside the drum to cover mounting holes or support components. Replace if cracked, broken, or missing.

This dryer drum support mount plate secures and stabilizes the drum assembly. Replace if cracked, broken, or missing to restore proper drum support.

Dryer not starting or displaying error codes? This electronic control board manages all dryer functions and cycles. Moderate difficulty repair.

This flat-head screw secures panels, brackets, or trim so they sit flush on your appliance. Replacing a worn or missing screw restores a tight fit and helps prevent vibration, rattling, or shifting components.

• Provides a countersunk, flush-mount fastener for panels, trim, brackets, or covers
• Helps maintain alignment and secure attachment during operation
• Replaces stripped, rusted, or missing hardware
• Symptoms can include loose panels or handles, rattling noises, or visible gaps/misalignment

• Disconnect power (and shut off gas, if applicable) before servicing
• Match screw length and thread to the original for proper fit
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Support the part being fastened to keep alignment while tightening

Replacement mounting nut secures panels, brackets, and studs in dryers. Restores tight fit for worn, stripped, or missing fastening hardware.