Parts for Maytag MGDB835DW4: Top And Console Parts

This replacement console is the outer housing that holds the appliance controls and display, restoring a clean, functional control area. It provides a finished appearance and secures the control components in place. What it does:

• Replaces a cracked, faded, or damaged control panel housing to improve appearance and protect internal controls
• Supports and aligns switches, buttons, and the display so controls operate reliably
• Helps prevent dirt and moisture from reaching electronic components behind the panel
• Compatible with consoles that use the same trim and mounting locations

• One console as shown

• High-level replacement: access requires removing the console trim and disconnecting power before starting
• Unplug the appliance or shut power at the breaker to avoid shock
• Keep screws and small parts organized during disassembly for reassembly
• If the console secures electronic components, handle with care to avoid damaging wiring or the display

The Overlay is an OEM replacement part for Whirlpool electric and gas dryers. It is an external decorative panel that fits over the dryer cabinet and door front.

Symptoms of a bad overlay include: 

• Unsightly exterior condition that detracts from dryer looks
• Potential rust or corrosion developing underneath 
• Loose, falling off or misaligned overlay panel

Causes of a bad overlay include physical damage like dents, scratches or cracks that compromise its aesthetic appearance. Exposure to moisture over time can also affect adhesive or paint coatings.

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore brand electric and gas dryers.

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

This replacement nut secures appliance parts and hardware to keep assemblies stable and prevent loose connections. It's a simple, direct replacement for worn or missing fastening hardware to restore proper fit and reduce vibration. What it does:

• Fastens mounting studs, brackets or panels to hold components in place
• Restores secure mechanical connections that can loosen over time
• Helps eliminate rattling, vibration and misaligned panels caused by missing or stripped hardware
• Provides a straightforward, durable replacement for corroded or damaged nuts

• Disconnect power to the appliance before beginning any repair
• Use the correct-size wrench or socket; ensure threads engage smoothly before tightening
• Tighten until snug—avoid overtightening that can strip threads or damage components
• Inspect mating threads and replace any damaged studs or hardware for a reliable repair

The Switch Mounting Screw is an OEM part compatible with Whirlpool washing machines. This screw securely mounts the cycle selector switch within the control console assembly. Proper fastening ensures dependable operation of control functions.  

Causes of a bad mounting screw can stem from stress cracks developing over multiple years of operation. Vibrations accumulate, slowly loosening connections housed in a wet environment.

Symptoms of a bad mounting screw include:

• Loose or rattling switch within the console face  
• Difficulty selecting cycles as buttons wobble out of place
• Water intrusion hastening corrosion of electrical terminals
• Potential shock hazards if live connections are exposed

This Whirlpool replacement screw restores a tight mounting point. It is compatible with brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This electronic control board serves as the appliance's main control, coordinating functions and powering key components. Replacing a failed board can restore reliable operation, accurate timing, and responsive controls.

• Directs operations based on user selections and sensor inputs to run each cycle
• Distributes power to motors, pumps, valves, and heaters as required
• Interfaces with the door/lid switch and user interface to start and advance cycles
• Common failure symptoms: won't start or no response from controls; stuck mid-cycle or won't advance; intermittent power; error codes or beeping

• Disconnect electrical power before servicing; follow all safety procedures
• Use ESD protection and handle the board by its edges
• Transfer wiring/connectors one at a time; reuse existing bracket/mounting hardware as applicable
• After installation, restore power and run the unit's diagnostic/service routine to verify operation and clear stored faults

This top panel replaces the appliance's cabinet top to restore a flush, secure surface and protect internal components. It's a direct-fit exterior panel used when the existing top is dented, bent, or damaged. What it does:

• Covers and protects the washer/dryer cabinet and internal components from debris and spills
• Provides the mounting surface for controls, console, and trim
• Restores a straight, even appearance when the original top is warped or dented
• Helps maintain proper alignment of adjoining panels and doors

• 1 top panel

• Unplug the appliance or disconnect power before starting work
• Keep fasteners organized and hand-tighten before final torque to ensure proper fit

The Console Clip is an OEM part compatible with Whirlpool dryers. This clip secures the control console assembly to the top panel, ensuring it is firmly mounted during operation. Properly functioning clips are necessary to maintain the correct alignment of controls and prevent detachment. 

Causes of a bad clip can include wear and fatigue from repeated opening and closing of the dryer door. Excessive force or impact could also bend or break the clip over time.

Symptoms of a bad clip include:

• Loose console assembly that is not securely fastened  
• Misaligned or dangling controls that do not sit flush
• Dislodged console at risk of detaching from housing
• Missing clip leaving an open mounting point

This OEM Whirlpool replacement clip is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Speaker is an OEM component specifically designed for Whirlpool brand washers. It alerts users with chime tones or voice prompts during cycle operation or any error states. Precise acoustic engineering allows for clear audio reception even amid operating vibrations. 

Symptoms of a bad speaker include: 

• No audio tones or voice prompts were heard  
• Muffled, distorted, or unusually loud sounds
• Speaker making rattling or buzzing noises

Causes can be damage from water damage, defects in the audio circuitry, or aging components. 

This speaker ensures optimal user communication. Without it, you cannot verify cycle progress or troubleshoot issues. Its dependable performance maintains the washer's convenience.

This Whirlpool OEM part fits perfectly while extending the equipment's lifespan. It is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This control knob attaches to the appliance's control shaft so you can select settings with a solid, positive feel. Replace a cracked, stripped, or missing knob to restore smooth operation and a clean, finished look.

• Attaches to a switch or valve shaft to select temperatures, burner levels, or cycles
• Transfers your hand turn to the control shaft for accurate setting changes
• Common symptoms: cracked hub, spins without engaging, wobbly/loose, falls off, or missing
• Helps maintain a uniform appearance across the control panel

• Disconnect power (and shut off gas, if applicable) before servicing
• Pull the old knob straight off the shaft; avoid prying against the control panel
• Align the insert with the shaft's flats or splines and press straight on until fully seated
• Match position- and finish-specific knobs to the original on models that use different knobs per location