Parts for Kenmore 790.46814991 (79046814991, 790 46814991): Top / Drawer Parts

This warmer drawer assembly replaces a failed or damaged warming drawer to restore the appliance's ability to keep cooked foods warm and ready to serve. Fits as a direct replacement for units using this OEM drawer assembly. What it does:

• Provides the insulated, heated compartment that maintains cooked-food temperature for serving
• Replaces cracked, bent or non-sealing drawers that allow heat loss
• Restores proper drawer movement and latch engagement for safe use
• Helps eliminate intermittent or complete loss of the warming function when the drawer assembly is damaged

• Disconnect power to the appliance before starting any repairs to avoid shock
• Handle the drawer carefully—edges and mounting tabs may be sharp
• Verify proper seating and alignment; ensure connectors and mounting clips engage fully
• If wiring or heating elements are exposed or damaged, replace those components per OEM instructions.

This glide is a low-friction slide used in select cooking appliances to support and guide a moving component, such as a lower drawer. Replacing a worn or broken glide restores smooth travel and proper alignment without sticking or scraping.

• Provides a smooth sliding surface for the mating part
• Helps keep the component aligned as it opens and closes
• Reduces friction and wear during movement
• Failure symptoms include sticking, scraping noises, uneven travel, or the component coming off track

• Disconnect power and allow the appliance to cool before servicing
• Remove the sliding component (e.g., drawer) to access the glide
• Remove the damaged glide and install the new one, transferring any screws or clips as needed
• Reinstall and test to ensure smooth, even movement

This glide is the low-friction slide piece used in select Frigidaire ranges and wall ovens to support a moving component. Replacing a worn glide restores smooth in-and-out movement, reduces binding, and helps prevent premature wear on mating rails. What it does:

• Provides a smooth, low-friction surface for a sliding drawer or rack
• Helps keep the component aligned on its track to avoid binding
• Reduces sticking and scraping noises during operation
• Common symptoms: hard-to-open/close movement, uneven travel, wobbling, or a visibly cracked/missing glide

• One glide

• Disconnect power and allow the appliance to cool before servicing
• Remove the drawer or rack to access the glide location
• Release screws or tabs securing the old glide; transfer any reusable hardware
• Install the new glide, and test for smooth travel

This is a medium burner pan that is used with ranges and stoves. The burner pan is located under the heating unit to catch any drips and spills. This prevents the drips from reaching the internal components of the stove where they could cause additional damage. Over time, the burner pan can be overly soiled and damaged and may need to be replaced. The process of replacing the medium burner pan takes only a few minutes. The first step is to unplug the stove or range. Next, the elements on the cooktop need to be lifted to access the parts underneath. The burner pan will be found in one of the cavities under the burners. These can be removed by hand and set aside. When replacing the burner pan, make sure the hole on the side is oriented to fit the terminals. Plug the elements back in and plug in the stove.The medium burner pan is made for use with ovens, ranges, and stoves manufactured by Kenmore and Frigidaire. It is sold as an individual product. This is an authentic OEM replacement part that is sourced directly from the manufacturer.

The Cap-Burner is an OEM replacement part for Frigidaire cooktops and ranges. It is a crucial component that covers and protects the gas burner assembly, while also distributing the flame evenly for optimal cooking performance.

Symptoms of a bad Cap-Burner:

• Uneven or irregular flame patterns 
• Difficulty in igniting or maintaining a steady flame
• Discoloration or warping of the cap due to excessive heat exposure
• Clogged or obstructed gas flow, leading to poor burner performance

Causes of a defective Cap-Burner can include prolonged exposure to high temperatures, impact damage, or general wear and tear over time.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore cooktops and ranges.

This door gasket seals the refrigerator door to help keep cold air in and warm, humid air out—reducing frost build-up and helping the appliance run more efficiently. Fits where a full perimeter door seal is required. What it does:

• Creates an airtight seal around the refrigerator door to maintain consistent internal temperatures.
• Helps prevent warm air infiltration, moisture, and frost accumulation inside the compartment.
• Reduces energy waste caused by a failing or damaged door seal.
• Common symptoms of a bad seal: condensation at the door, frost on shelves, fluctuating temperatures, or higher energy use.

• Disconnect power to the appliance before attempting any service.
• Remove the old gasket carefully; replacement typically seats into the door channel around the full perimeter.
• Inspect and, if needed, adjust door alignment and hinge condition to ensure a proper seal.

Hex washer head ,10-32 x 0.375. Ground

This oven rack is a replacement wire shelf that supports cookware and bakeware inside the oven cavity, restoring proper spacing and airflow for even cooking and broiling. Ideal when the original rack is bent, rusted, or missing. What it does:

• Provides a stable surface for pans, baking sheets and cookware
• Restores correct oven spacing for even heat circulation
• Replaces bent, warped or corroded racks that catch or bind
• Enables use of multiple rack positions for different cooking needs

• Allow the oven to cool completely and disconnect power before installing
• Position rack with the rolled edges toward the oven walls and slide into desired rack guides
• Use gloves to avoid sharp edges and protect finishes
• Clean gently with non-abrasive cleaners; do not use oven self-clean while rack is in place unless rack is rated for self-clean cycles

Note: Due to a factory change, the new glide may be shorter than your original. Per Factory: The original part was 19.75". The new part is 16.25" and will install and function the same.