Parts for Kenmore 790.97102012 (79097102012, 790 97102012): Top / Drawer Parts

Oven rack glide for electric ranges. Installs along the oven cavity wall to guide racks smoothly. Replace if worn, broken, or missing for proper support.

Replacement drawer glide for electric and gas ranges. Guides storage drawer along its track for smooth opening and closing. Replaces cracked or worn glides.

Fix a burner that won't heat on your glass cooktop. This radiant surface element restores even heating and temperature control. DIY-friendly repair.

This 100W radiant element replaces a failed warming element to restore gentle, even heat in the appliance's warmer/drawer. It delivers low-profile radiant heat for keeping food warm between cooking and serving. What it does:

• Radiates low-level heat to maintain food temperature in the warmer or drawer
• Replaces a broken or non-heating warmer element
• Common symptom: warmer drawer not holding temperature or not heating
• Works as the heating element that sits under the warming surface to provide consistent warmth

• Disconnect power to the appliance before attempting service
• Inspect mounting and wiring; replace any damaged connectors or mounting hardware as needed
• Handle the element carefully to avoid bending or damaging the heating surface

Burner won't heat or randomly stays on? This range heating element restores proper burner function. DIY repair takes about 30 minutes with basic tools.

Burner not heating? This 6-inch surface heating element restores cooktop function. DIY repair in 10-30 minutes with basic tools and simple instructions.

This is a metal hinge bracket that secures the main cooktop to the range frame and allows it to be lifted for access to components underneath. It connects the cooktop panel to the body of the range at the hinge point. Replace this bracket if it is bent, broken, or missing, which can cause the main top to sit unevenly or not stay properly secured.

Replace the channel trim on your range door when it becomes cracked, broken, or damaged. This structural component installs along the door edge for a secure fit.

Replacement oven door handle for your range. Installs on the front door panel. Needed when the original handle is cracked, broken, loose, or missing.

This replacement part is a black element mounting clip used in ranges or wall ovens. This clip is used for surface elements on electric ranges and ovens. The clip itself connects the surface of the element to the support bracket which allows the stove to heat up. The user might need a new clip or clips if the heating element on the stove is loose, if the heating element is completely detached, or if the clip itself is bent or broken. This clip is black and made of sturdy metal that can withstand heat as well as strain on the clip itself. Installation of this clip is very simple as it just requires replacing the old one with a new one and making sure it is secure. Pliers might be required if the old clip is bent or stuck near or on the heating element. There are no special tools needed for this repair. This is an OEM part sourced directly from the manufacturer. It is sold individually. This part is compatible with machines from Frigidaire and other brands like Electrolux, Gibson, Kelvinator, Crosley, Westinghouse, and more.

Replacement mounting screw that secures panels, trim, and components in ranges and ovens. Needed when original screws are lost, stripped, or damaged.

This is a heating element designed for the warming drawer of a range. It provides low, consistent heat to keep food warm after cooking. Replace this element if your warming drawer no longer heats, heats unevenly, or has visible damage such as cracks or burn marks.

Mounting bracket that secures the heating element in your range. Replace this bracket if it's bent, broken, cracked, or missing to properly support the element.

Range won't heat or shuts off unexpectedly? A faulty thermal fuse may be the cause. This safety component protects against overheating. DIY repair.

This metal rack fits inside the warming drawer beneath the oven, providing a flat surface to hold plates, dishes, or cooked food at a warm serving temperature. It slides in and out of the drawer on built-in guides. Replace it if the rack is bent, warped, rusted, or missing, which can prevent proper food placement and even heat distribution in the warming drawer.

This damper is the refrigerator air inlet that controls airflow between compartments to help maintain even temperatures. Replaces a worn or stuck damper to restore proper cold-air distribution and reduce temperature imbalance. What it does:

• Regulates airflow from the freezer to the fresh-food compartment to help stabilize interior temperatures.
• Helps correct symptoms like uneven cooling, warm spots in the fridge, or overly cold freezer-to-fridge balance.
• Prevents over-working of the compressor by allowing proper air circulation when functioning.
• Can become stuck or fail to open/close, producing reduced airflow or unusual noises.

• One damper assembly.

• Disconnect power to the appliance before beginning any repair.
• Access typically requires removing interior liners or control housing—handle panels and clips gently to avoid damage.
• Compare the new part to the removed component to fit before reinstalling panels.

10-24 x 1/2 inch machine screw that secures temperature probe and thermistor brackets to cooktop, oven, and range chassis. Replace if missing or stripped.

This is the exterior handle mounted on the oven door, used to open and close the door during cooking. It attaches to the door with mounting brackets or screws. Replace this handle if it is cracked, broken, loose, or if the mounting points have become damaged, making it difficult to safely open the oven door.

This rivet is a small metal fastener used to secure panels, trim, and small appliance components so assemblies stay stable and aligned. Replacing a damaged or missing rivet restores proper fit and reduces noise from loose parts. What it does:

• Secures sheet metal panels, trim pieces, or small brackets in place
• Keeps components aligned and prevents shifting or sagging
• Replacing worn or broken rivets can stop rattling or loose-feeling panels
• Use when a rivet is missing, bent, sheared, or otherwise damaged

• Typically installed with a pop-rivet tool or pressed into place depending on application
• Remove damaged rivets by drilling out the center or cutting them free before installing the replacement
• Wear eye protection and follow tool manufacturer safety instructions

Wire harness for ranges. Connects electrical components inside your range. Replace if wires are frayed, damaged, or connections are loose or corroded.

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

Replaces damaged or frayed wire harness that connects electrical components in your range. Install when wiring is cracked, melted, or corroded.

Size: 6-20 x 0.312 inch.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.