Parts for Ge PTW600BPR0DG: Top Panel & Lid Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

The Main Control Board with Instructions is an OEM part for GE washing machines. It is the central processing hub that controls all wash cycle functions through software programming.

Causes of board failure may be component fatigue from long-term operational use.  

Symptoms include:

• Cycles not completing or failing to advance
• Inoperative or unresponsive cycle buttons
• "Error" codes displayed frequently
• Noisy or grinding sounds from internal components

This OEM GE  part is also compatible with Hotpoint, RCA, and some Kenmore models.

8-18 hi/lo 5/8

The Ground Screw is an OEM part for GE dryers. It ensures proper grounding and electrical safety for your dryer. This screw securely connects the ground wire to the dryer chassis, providing a path for electrical current to safely discharge in the event of a fault or power surge.

A bad Ground Screw can lead to electrical issues and potential safety hazards. Causes of a bad Ground Screw can include corrosion, loose connections, or damage due to accidental mishandling or improper installation.

Symptoms of a bad Ground Screw include:

• Intermittent dryer operation
• Visible signs of damage or deterioration on the screw or ground wire
• Tripped circuit breakers or blown fuses

Replace your faulty or damaged Ground Screw with this genuine OEM GE part to ensure proper grounding and electrical safety for your dryer. 

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

The Thermistor is an OEM part for GE washers. This thermistor monitors and regulates the temperature inside your GE washer during the different cycles.

The thermistor ensures accurate temperature sensing by measuring the temperature of the water or air inside the washer and sends this information to the control board, allowing it to adjust the heating elements or cooling mechanisms accordingly.

A bad thermistor can occur due to wear and tear, exposure to extreme temperatures, or electrical malfunctions. If you notice symptoms such as the washer not heating or cooling properly, error codes indicating a faulty thermistor, or inconsistent temperature readings, it may be time to replace the component.

Symptoms of a bad thermistor include:

• Washer not heating or cooling properly
• Error codes indicating a faulty thermistor
• Inconsistent temperature readings

Restore accurate temperature control by replacing the faulty thermistor with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This lid lock striker attaches to the washer lid and engages the lock mechanism when closed. Replacing a worn striker restores proper lid locking so cycles can start and spin safely.

• Provides the physical tab the lid lock/switch detects to verify the lid is closed
• A damaged or missing striker can cause the lid not to lock, washer not to start or spin, cycle pauses, or a flashing lid lock indicator/error
• Helps ensure the control can safely allow agitation and spin only when the lid is closed
• Restores alignment between the lid and lock to prevent false "lid open" detection

• Disconnect power before servicing; moving parts and electrical components can be hazardous
• Open the lid and note the striker's orientation and position
• Remove the old striker and install the new one using the existing mounting method; do not overtighten
• Close the lid to confirm the lock engages smoothly before running a cycle

The Lid Stanchion is an OEM part for GE washing machines. It securely mounts the washer lid in place through hinges at the top of the cabinet.

Symptoms of a bad lid stanchion include:

• Loose, wobbly, or misaligned washer lid that does not stay flush   
• Gaps visible around lid sealing surfaces allowing air/moisture in
• Grinding or creaking noises heard from the hinge area during the opening

Causes involve worn, stripped, or corroded hinge mounting points from repeated opening/closing cycles over time. Failure risks lid detachment.

This OEM GE replacement lid stanchion ensures safe and stable lid support for proper sealing. Rely on sturdy stanchions to protect against broken lids. Replace yours today for smooth, reliable openings and closings.

Compatible with some Hotpoint, RCA, and Kenmore washers as well, this stanchion maintains critical structural rigidity.

This lid lock bezel frames and supports the washer's lid lock on the top panel. Replacing a cracked or missing bezel keeps the lock properly seated and restores a clean, finished appearance around the opening.

• Secures and aligns the lid lock in the top cover opening
• Provides a finished edge and protects the panel around the lock
• Helps prevent the lock from shifting, rattling, or sitting unevenly
• Common signs it's needed: cracked/missing bezel, loose or misaligned lock, visible cosmetic damage

• Disconnect power before servicing.
• Access the lid lock from beneath the top panel; remove fasteners to free the lock, then release the bezel's retaining tabs.
• Seat the new bezel in the opening, reinstall the lock, and ensure the lid closes and locks properly.
• Handle wiring carefully; avoid pulling on the harness.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This glass lid assembly fits top-load washers. It restores a clear view and proper closure so the lid switch can engage and wash and spin cycles can run safely.

• Replaces cracked, shattered, or warped lids that won't close properly
• Aligns with the lid lock/strike so the washer can start and spin
• Shields the tub from splashes while the glass window keeps contents visible
• Helps resolve "won't start" or "won't spin" when the lid can't engage the lock

• Unplug the washer and turn off water; wear gloves and eye protection when handling glass
• Support the lid, remove hinge screws, and lift off the old lid
• Transfer any reusable hardware from the original lid as needed
• Mount the new lid on the hinges, secure screws, and confirm it closes and engages the lock

This lid lock and harness assembly restores safe washer operation. It locks the lid during spin and relays lid-closed status to the control, helping resolve no-start/no-spin conditions and a flashing lid-lock light.

• Locks the lid during spin when commanded by the control
• Detects lid position and sends a signal to the control board
• Helps prevent the washer from running with the lid open
• Typical failure signs include the washer not starting or not spinning, cycles pausing mid-cycle, or a blinking lid-lock light/clicking sound

• Unplug the washer before servicing; turn off water if you need to move the unit
• Access the lock by lifting or removing the top panel; remove mounting screws or release tabs
• Route the new harness along the original path and secure in clips; fully seat connectors at the control
• Run a spin test to verify lock/unlock operation

This is the replacement dispenser box and drawer assembly for select top-load washers. It holds your laundry additives and channels them into the tub at the proper time, restoring reliable dispensing and smooth, easy drawer operation.

• Houses laundry products and meters them into the wash via incoming water flow
• Replaces cracked, warped, or leaking dispenser housings and broken/sticky drawers
• Common symptoms include detergent/softener remaining in the drawer, leaks at the dispenser area, drawer hard to open/close, or visible damage to the housing/drawer
• Diamond Gray finish matches the appliance's original appearance

• Disconnect power and shut off water before servicing
• Access the dispenser from the top; remove trim/screws/clips as needed and detach connected hoses
• Note hose routing and clamp positions so they're reinstalled correctly
• After installation, restore water and power, then run a test cycle to check for proper dispensing and leaks

This shower plate gear and seal assembly replaces the worn drive gear and sealing components in the dishwasher dispenser box to restore proper detergent dispensing and spray distribution. Helps stop leaks and inconsistent dispense cycles when the assembly is faulty. What it does:

• Drives the dispenser shower plate so detergent is evenly released during the wash cycle.
• Replaces worn gear teeth that can cause noisy operation or failure to rotate.
• Replaces seals that can harden or crack and lead to leaks around the dispenser box.
• Addresses symptoms such as detergent not dispensing, water leaking from the dispenser area, or abnormal dispenser noise.

• Disconnect power and water to the appliance before beginning any repair.
• Inspect surrounding components and mounting points; replace any damaged clips or fasteners for a watertight fit.
• Use common hand tools; take care not to overtighten fasteners or damage plastic parts.

This siphon cap seals and protects a refrigerator drain/siphon opening to help direct water to the drain and reduce leaks or odors. It's a small replacement piece that restores the intended drain seal and routing. What it does:

• Seals the siphon/drain outlet to prevent unwanted water from leaking or pooling
• Helps maintain correct water routing to the drain during defrost and ice/water use
• Reduces chance of odors traveling back from the drain passage
• Addresses symptoms such as water under the appliance, slow draining, or dripping near the drain area

• One siphon cap (exact part as listed)

• High-level replacement; inspect the drain area and surrounding seals before installation
• Ensure the appliance is powered off and water supply is shut at the valve if accessing water components
• Clean the drain opening of debris before seating the new cap for a secure fit
• If damage extends beyond the cap (cracked housing, clogged drain), consider additional service

This dispenser drawer assembly is the pull-out detergent/bleach/fabric softener tray for the washer. Replacing a cracked or sticking drawer restores smooth operation and proper dispensing, while matching the appliance's Diamond Gray finish.

• Holds detergent, fabric softener, and bleach; channels rinse water to flush them into the tub at the correct time
• Replaces broken, warped, or loose drawer fronts/handles that hinder smooth opening and closing
• Diamond Gray color maintains a uniform, factory look

• Disconnect power and turn off water before servicing
• Fully extend the drawer and press the release tab to remove it from the rails
• Transfer any removable inserts or siphon caps from the old drawer
• Slide the new drawer into the guides until it seats and operates smoothly

This 10-32 machine screw fastens small appliance components and replacement assemblies, restoring secure mounting and reliable electrical or panel connections. Its length fits common cabinet, control, and bracket attachments. What it does

• Secures control boards, panels, brackets, and grounding tabs using a 10-32 machine thread
• Replaces stripped or missing mounting screws that allow panels or parts to rattle or shift
• Helps restore stable electrical connections where a threaded fastener is required
• Works where a 1.31 in (approx. 1-5/16 in) long 10-32 screw is specified

• Power off and unplug the appliance before beginning any repair
• Match thread size and length to the original screw; do not force a wrong-size fastener
• Start threads by hand to avoid cross-threading; tighten securely but do not overtighten
• Use appropriate tools and wear eye protection when working on metal assemblies

This lid lock harness clip secures the lid lock wire harness to the washer cabinet or top. It keeps the wiring routed and protected to help prevent chafing, snagging, and intermittent lid-lock performance issues. What it does / common symptoms:

• Holds the lid lock wire harness in place along the cabinet/top
• Maintains proper routing to avoid pinching or rubbing on moving parts
• Reduces vibration-related wear on the wiring
• Symptoms of a failed/missing clip: loose or dangling harness, scuffed insulation, intermittent lid-lock response

• 1 lid lock wire harness clip

• Disconnect power before servicing
• Access the lid lock wiring path (lift top/remove console as required by your model)
• Release the old clip from the panel and harness; snap the new clip into the mounting hole and secure the harness
• Ensure the harness has adequate slack and is not pinched before restoring power

This is a self-tapping Plastite screw with a hex washer head and a 5/8 in. length that secures plastic and thin-sheet components. Use it to replace missing or damaged mounting screws for a snug, reliable fit. What it does:

• Forms threads in plastic (Plastite style) to fasten panels, brackets, and trims.
• Hex washer head provides a larger bearing surface for better holding power.
• Replaces stripped, corroded, or missing screws to stop loose or rattling parts.
• Works where a self-tapping screw is required for secure mounting without a separate nut.

• Use the correct hex/nut driver and a properly fitting bit to avoid stripping the head.
• Hand-start the screw and drive straight to prevent cross-threading; stop when snug—do not overtighten into plastic.
• Unplug the appliance or shut off power before disassembling or working near electrical components.
• Replace with the same screw type and size to maintain proper fit and function.

The Water Inlet Valve Seal is an OEM part for GE washing machines, designed to ensure a watertight seal around the water inlet valve. This part helps prevent leaks by sealing the connection between the water inlet valve and the washing machine's internal tubing. 

Causes of a bad water inlet valve seal include normal wear and tear, exposure to hard water minerals that can erode the seal, and improper installation that may strain or damage the seal.

Symptoms of a bad Water Inlet Valve Seal include:

• Water leaking from the back or underside of the washing machine
• Visible signs of wear or damage to the seal
• Unexplained increase in water usage or utility bills, which may indicate a slow leak

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Water Inlet Valve is an OEM part for GE washing machines. It is responsible for controlling the entry of hot and cold water into the washing machine. This valve opens and closes at the appropriate times during the wash cycle to allow water to enter based on the selected temperature and wash settings.

Causes of a bad water inlet valve include mineral deposits from hard water, which can block the valve, and wear and tear from regular use, which can cause the valve to fail mechanically or electronically. Additionally, if the screens that filter the water before it enters the valve become clogged, water flow can be restricted, affecting the washing machine’s performance.

Symptoms of a malfunctioning water inlet valve include:

• The machine not filling with water.
• Water entering the machine slowly.
• Water leaking around the valve area.
• A noisy valve during operation.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.