Parts for Ge GTW845CSN1WS: Top Panel & Lid Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This level sensor monitors and signals the appliance's water level so the machine fills and stops at the correct point. Replaces a failed sensor to restore reliable water sensing and cycle operation. What it does:

• Detects water level and sends the signal to the control board for proper fill and cycle timing
• Can prevent overfilling or underfilling when functioning correctly
• Common symptom: washer runs but won't fill to the proper level or cycles erratically
• Linked to long fill times, no fill, or error codes related to water level detection

• One level sensor

• Disconnect power and water before starting any repair to avoid shock or flooding
• Handle the sensor and electrical connectors carefully to avoid damage
• Verify hose/tube connections and wiring match the replacement part before powering the appliance

The Ground Screw is an OEM part for GE dryers. It ensures proper grounding and electrical safety for your dryer. This screw securely connects the ground wire to the dryer chassis, providing a path for electrical current to safely discharge in the event of a fault or power surge.

A bad Ground Screw can lead to electrical issues and potential safety hazards. Causes of a bad Ground Screw can include corrosion, loose connections, or damage due to accidental mishandling or improper installation.

Symptoms of a bad Ground Screw include:

• Intermittent dryer operation
• Visible signs of damage or deterioration on the screw or ground wire
• Tripped circuit breakers or blown fuses

Replace your faulty or damaged Ground Screw with this genuine OEM GE part to ensure proper grounding and electrical safety for your dryer. 

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

The Top Cover is an OEM part for GE washing machines. It serves as the top panel enclosure for the washer, covering internal components and shielding them from potential water damage or intrusion of foreign objects. The top cover also plays a cosmetic role, providing a sleek design finish to the top of the appliance.

Symptoms of a bad top cover include:  

• Cracks, breaks, or looseness developing in the plastic material over time
• Missing or damaged mounting screws  
• Water leaks or moisture inside the panel enclosure area
• Dents, dings, or other exterior damage affecting appearance

Causes of a bad top cover are generally related to wear and tear from repeated usage and loading/unloading of clothes over the years. General handling can also lead to minor impacts or stresses that result in cracks or breaks.

This genuine GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Thermistor is an OEM part for GE washers. This thermistor monitors and regulates the temperature inside your GE washer during the different cycles.

The thermistor ensures accurate temperature sensing by measuring the temperature of the water or air inside the washer and sends this information to the control board, allowing it to adjust the heating elements or cooling mechanisms accordingly.

A bad thermistor can occur due to wear and tear, exposure to extreme temperatures, or electrical malfunctions. If you notice symptoms such as the washer not heating or cooling properly, error codes indicating a faulty thermistor, or inconsistent temperature readings, it may be time to replace the component.

Symptoms of a bad thermistor include:

• Washer not heating or cooling properly
• Error codes indicating a faulty thermistor
• Inconsistent temperature readings

Restore accurate temperature control by replacing the faulty thermistor with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

The Leveling leg is an OEM component specifically designed for GE washing machines. This accessory provides stability for the entire unit during operation. 

Symptoms of a bad Leveling leg can include:

• Excessive tipping or leaning of the washer during operation   
• Walks or moves across a tile floor while operating  
• Deterioration like rust developing or cracks appearing

Causes involve long-term exposure to vibration and cycles of weight variations inside the washer. Over time, wearing down can potentially compromise support.

This GE replacement part is also compatible with Hotpoint, RCA and select Kenmore models. 

This lid lock striker replaces the striker that the lid lock/latch grabs to secure the washer lid during cycles, restoring reliable lid engagement so the machine can start and run safely. What it does:

• Provides the mating surface for the lid lock assembly to hold the lid closed during wash and spin cycles.
• Helps prevent the washer from starting or spinning when the lid is not properly secured.
• Commonly associated with symptoms such as lid not latching, lid lock error messages, cycles that won't start, or cycles stopping mid-cycle.
• Realigns the lid/latch interface when worn or damaged to restore proper locking action.

• Disconnect power to the washer (unplug or turn off the circuit breaker) before attempting any service.
• Access may require removing the cabinet top or an access panel per the manufacturer's instructions; keep track of fasteners and watch for sharp edges.
• Verify proper alignment of the striker with the lid latch before reassembling panels; test lid lock function after restoring power.

This lid front corner bumper cushions the washer lid and helps reduce noise, wear and abrupt contact when the lid closes. It restores smooth, quiet operation at the lid's front corner. What it does:

• Acts as a soft contact point between the lid and cabinet to dampen impact and vibration
• Prevents metal-on-metal contact that can cause chipping, scratching or rattling
• Helps keep the lid aligned for consistent closing and latching
• Commonly replaced when the lid squeaks, chips, or does not sit flush

• Lid front corner bumper

• Disconnect power to the appliance before beginning any work
• Typically installs by hand or with light pressure into the lid or cabinet corner; use gentle force to avoid damage
• Inspect surrounding area for cracks or wear and replace other damaged bumpers if needed

Center lid bumper cushions and aligns the washer lid to reduce noise and prevent metal-to-metal contact. Replace a worn or missing bumper to restore quieter, smoother lid closing and protect the lid edge and cabinet finish. What it does:

• Cushions the lid to reduce slamming, rattling and impact noise
• Helps the lid sit evenly to prevent rubbing or uneven closing
• Protects the lid edge and cabinet finish from contact damage
• Common symptoms: noisy or uneven lid closing, visible wear or missing bumper

• Unplug the appliance or disconnect power before servicing.
• Typically snaps or presses into a mounting boss under the lid; remove the old bumper before installing the new one.
• Use a non-marring tool or gloved hand to avoid scratching the lid; inspect surrounding mounting area for damage.

The Lid Lever Arm is an OEM part for GE washing machines. This component is crucial for the proper functioning of the washer's lid mechanism, ensuring that the lid locks securely during operation and allows for safe and efficient washing cycles.

Over time, the lid lever arm can become worn out or damaged due to regular use, improper handling, or mechanical failure. Causes of a bad lid lever arm include physical damage, wear and tear from repeated use, or issues with the linkage that connects it to the locking mechanism.

Symptoms of a bad lid lever arm include:

• The washer lid not locking properly
• The washing machine not starting or pausing unexpectedly
• Error codes related to lid lock issues
• The lid feeling loose or misaligned

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

A replacement funnel bezel for the dispenser that restores the dispenser opening and helps guide water or ice into your cup with a finished look. Fits the dispenser area to repair cosmetic damage or broken trim. What it does:

• Replaces cracked, broken or missing dispenser trim that can catch drips and obstruct dispensing
• Guides water and ice into the cup to reduce splashing and misalignment
• Restores the original appearance of the dispenser opening
• Works with the dispenser assembly to help maintain proper user access

• Disconnect power to the appliance before servicing to reduce shock risk
• Usually installs from the front of the dispenser; remove adjacent trim or liners if needed for access
• Handle gently to avoid scratching the finish and align snaps or tabs before pressing into place

The Glass Frame Assembly is an OEM part for GE washing machines. It serves as both a protective barrier and a see-through lid on the washing machine. The glass frame allows users to monitor wash loads without having to open the door and risk water spillage. 

Symptoms of a bad glass frame assembly include:

• Cracks or chips in the glass that compromise strength and viewing ability
• Warping, bending, or other distortions of the frame itself
• Binding, sticking, or troublesome opening/closing of the lid 

Causes of failure are typically impacts or accidental mishandling that result in damage over time. Glass can crack or frames become misshapen from repeated use and closing of the heavy lid.

This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Lid Lock Service Kit is an OEM part for GE washing machines. This kit includes the components necessary to ensure that the washer lid remains securely locked during operation, preventing the lid from being opened when the washer is in use. This safety feature is crucial for top-load washers, ensuring safe and efficient operation by preventing access to the washer drum during cycles.

The kit includes:

• Lid Lock & Harness Assembly
• White Bezel
• Gray Bezel
• White Strike
• Gray Strike

Common causes of a malfunctioning lid lock include wear over time, damage to the lock mechanism, or electrical issues that prevent the lock from engaging or disengaging properly. Exposure to moisture and constant use can also affect the performance of the lid lock system.

Symptoms of a bad lid lock include:

• The washer not starting or advancing in the cycle
• Error codes related to the lid lock
• The lid not locking or unlocking as expected
• The washer stopping mid-cycle

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This dispenser lid bezel restores the finished trim around your refrigerator's ice and water dispenser, improving appearance and protecting internal dispenser components from dirt and damage. Simple replacement for cracked, warped, or missing trim. What it does:

• Replaces damaged or cracked dispenser trim to restore a clean, finished look.
• Protects dispenser components and helps keep the dispensing area free of debris.
• Helps maintain proper alignment and access to the dispenser opening for smooth filling.
• Common symptom: visible cracks, chips, warping, or missing bezel trim.

• Disconnect power to the appliance before starting work; shut off the refrigerator's water supply if applicable.
• Use basic hand tools and a non-marring pry tool to remove the old bezel and snap or screw the replacement into place.
• Inspect mounting clips or screws during removal and replace any that are damaged.

A replacement smart dispense box that houses the fridge dispenser components and directs water/ice flow to the dispenser. Restores proper dispensing operation and secures dispenser parts inside the cabinet opening. What it does:

• Replaces the dispenser housing that channels water and ice from internal components to the external dispenser
• Helps stop leaks and misalignment caused by cracked or damaged dispenser boxes
• Restores proper fit and alignment for the actuator, chute, and related dispenser parts
• Resolves symptoms like water dripping, dispenser misfeeds, or loose/displaced dispenser components

• For repair technicians or experienced DIYers; disconnect power and water before starting
• Remove interior trim and dispenser components to access and replace the housing
• Inspect adjacent seals, gaskets, and mounting clips; replace if damaged
• Confirm water supply is off and test dispense operation after reassembly

This replacement siphon cap fits the washer's dispenser assembly. The insert creates the siphon action that empties the additive cup during the rinse cycle, helping prevent standing liquid and residue so liquid additives dispense as intended.

• Forms a siphon in the dispenser cup so liquids empty at the proper time
• Helps reduce standing water and residue buildup in the dispenser
• A worn or missing cap can contribute to odors or buildup in the dispenser area

• Unplug the washer and turn off water before servicing
• Remove the dispenser drawer or cup and lift out the old siphon cap
• Clean the dispenser area; press the new cap in firmly so it seats evenly
• Reinstall the drawer/cup and run a rinse to ensure proper dispensing

This fabric softener drawer is the replacement dispenser cup that holds and releases liquid fabric softener during the wash cycle, restoring proper softener delivery and preventing overflow or buildup in the drawer area. What it does

• Holds fabric softener and routes it into the washer at the correct time in the cycle.
• Helps prevent over-dispensing and keeps softener contained until release.
• Restores proper drawer operation when the original is cracked, warped, or clogged.
• Can stop leaks or drips from the dispenser area caused by a damaged drawer.

• Disconnect power to the appliance before beginning any service.
• Remove the old drawer by pulling it out and releasing any retention clips; install the new drawer by sliding until it seats.
• Inspect the dispenser housing for residue or damage and clean before installing the replacement.

The Lid Hinge is an OEM part for GE washers. It provides the mounting and fulcrum point for the washer lid, allowing smooth movement between open and closed positions. The sturdy hinge construction is designed to withstand repetitive use over many cycles.

Causes of a bad lid hinge can include fatigue from extended use, damage or loosening of mounting screws, or impact dents deforming the metal.

Symptoms include:

• Looseness, wobbling, or sagging of the washer lid 
• Difficulty fully opening or closing the lid securely
• Noise or squeaking emitted from the hinge area
• Physical deformation reducing the proper range of motion

This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. Replacing a worn or faulty lid hinge ensures comfortable, predictable lid movement for years to come.
 

A single replacement screw used to secure the lid hinge on top-load washers. Replaces a worn or missing hinge fastener so the lid stays aligned and operates smoothly. What it does

• Secures the lid hinge assembly to the washer cabinet or lid
• Restores proper lid alignment and reduces wobble or sagging
• Helps stop the lid from shifting, binding, or making noise when opened/closed
• Used when original screw is missing, stripped, or damaged

• One lid hinge screw

• Disconnect power and water supply before working on the washer
• Support the lid and hinge assembly while removing and installing the screw to prevent injury or damage
• Use the correct screwdriver or bit to avoid stripping the screw head

This 10-32 machine screw fastens small appliance components and replacement assemblies, restoring secure mounting and reliable electrical or panel connections. Its length fits common cabinet, control, and bracket attachments. What it does

• Secures control boards, panels, brackets, and grounding tabs using a 10-32 machine thread
• Replaces stripped or missing mounting screws that allow panels or parts to rattle or shift
• Helps restore stable electrical connections where a threaded fastener is required
• Works where a 1.31 in (approx. 1-5/16 in) long 10-32 screw is specified

• Power off and unplug the appliance before beginning any repair
• Match thread size and length to the original screw; do not force a wrong-size fastener
• Start threads by hand to avoid cross-threading; tighten securely but do not overtighten
• Use appropriate tools and wear eye protection when working on metal assemblies

This lid lock harness clip secures the lid lock wire harness to the washer cabinet or top. It keeps the wiring routed and protected to help prevent chafing, snagging, and intermittent lid-lock performance issues. What it does / common symptoms:

• Holds the lid lock wire harness in place along the cabinet/top
• Maintains proper routing to avoid pinching or rubbing on moving parts
• Reduces vibration-related wear on the wiring
• Symptoms of a failed/missing clip: loose or dangling harness, scuffed insulation, intermittent lid-lock response

• 1 lid lock wire harness clip

• Disconnect power before servicing
• Access the lid lock wiring path (lift top/remove console as required by your model)
• Release the old clip from the panel and harness; snap the new clip into the mounting hole and secure the harness
• Ensure the harness has adequate slack and is not pinched before restoring power

This is a self-tapping Plastite screw with a hex washer head and a 5/8 in. length that secures plastic and thin-sheet components. Use it to replace missing or damaged mounting screws for a snug, reliable fit. What it does:

• Forms threads in plastic (Plastite style) to fasten panels, brackets, and trims.
• Hex washer head provides a larger bearing surface for better holding power.
• Replaces stripped, corroded, or missing screws to stop loose or rattling parts.
• Works where a self-tapping screw is required for secure mounting without a separate nut.

• Use the correct hex/nut driver and a properly fitting bit to avoid stripping the head.
• Hand-start the screw and drive straight to prevent cross-threading; stop when snug—do not overtighten into plastic.
• Unplug the appliance or shut off power before disassembling or working near electrical components.
• Replace with the same screw type and size to maintain proper fit and function.

The Water Inlet Valve Seal is an OEM part for GE washing machines, designed to ensure a watertight seal around the water inlet valve. This part helps prevent leaks by sealing the connection between the water inlet valve and the washing machine's internal tubing. 

Causes of a bad water inlet valve seal include normal wear and tear, exposure to hard water minerals that can erode the seal, and improper installation that may strain or damage the seal.

Symptoms of a bad Water Inlet Valve Seal include:

• Water leaking from the back or underside of the washing machine
• Visible signs of wear or damage to the seal
• Unexplained increase in water usage or utility bills, which may indicate a slow leak

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Water Inlet Valve is an OEM part for GE washing machines. It is responsible for controlling the entry of hot and cold water into the washing machine. This valve opens and closes at the appropriate times during the wash cycle to allow water to enter based on the selected temperature and wash settings.

Causes of a bad water inlet valve include mineral deposits from hard water, which can block the valve, and wear and tear from regular use, which can cause the valve to fail mechanically or electronically. Additionally, if the screens that filter the water before it enters the valve become clogged, water flow can be restricted, affecting the washing machine’s performance.

Symptoms of a malfunctioning water inlet valve include:

• The machine not filling with water.
• Water entering the machine slowly.
• Water leaking around the valve area.
• A noisy valve during operation.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This water valve harness is a direct-replacement wire harness that connects the refrigerator's water valve to the control and power source, restoring proper electrical connection for water dispensing and ice maker fill functions. What it does:

• Provides the electrical connections between the fridge control and the water inlet/solenoid valve
• Restores power/signal delivery to the water valve so the dispenser and icemaker can fill
• Commonly used when the valve won't actuate or water flow is intermittent
• Helps replace damaged, corroded, or broken wiring/connectors that prevent reliable operation

• Disconnect power and turn off the water supply before beginning work
• Match connector shapes and pin counts; do not force connectors or bend pins
• Inspect mating connectors and valve terminals for corrosion; replace if needed
• Secure harness away from sharp edges and moving parts; test dispenser/icemaker after reassembly

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.