Parts for Ge GTWN7450D0WW: Top Panel & Lid Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This shield pressure sensor detects and reports pressure changes to the appliance control so water and air systems operate correctly. Replacing a failing sensor restores accurate pressure feedback for proper cycle control and performance. What it does:

• Monitors pressure changes and sends a signal to the control board for correct cycle operation
• Helps the appliance detect fill level, drain status or airflow depending on application
• A faulty sensor can cause incorrect cycles, error codes, or fill/drain problems
• Works as the system-level feedback component between plumbing/air paths and electronics

• Disconnect power to the appliance before starting any repair
• Handle the sensor and electrical connector carefully to avoid damage
• Ensure hoses/lines and electrical connectors are routed and seated as originally installed

This rubber lid bumper cushions the washer lid to prevent metal-on-metal contact and reduce noise and wear. It restores proper lid seating and helps stop banging or rattling during operation. What it does:

• Cushions the lid edge to absorb impact and reduce noise
• Helps align the lid for secure closing and proper latch engagement
• Prevents lid wear and chipping from repeated contact
• Simple replacement for visible cracking, compression, or missing bumpers

• One rubber lid bumper

• Designed for top-load washer lids; install by pushing into the lid hole or slot until seated
• No special tools typically required; inspect mating surfaces and replace any damaged fasteners
• Disconnect power before performing any repairs that expose electrical components or switches

Size: 8 - 18 ab.

This genuine replacement clip secures interior appliance parts so panels and components stay in place and operate quietly. It restores proper fit and helps stop rattles or loose trim caused by a broken or missing retainer. What it does:

• Secures and aligns panels, trim, or internal components to prevent shifting
• Stops rattling or vibration caused by a loose or missing clip
• Restores proper fit where the original fastener has broken or worn
• Fits the original mounting point and snaps into place for a firm hold

• Disconnect power to the appliance before servicing to avoid electrical shock
• Access the clip location by removing the panel or trim per your model's service instructions
• Press the clip into the mounting slot until it snaps; replace any damaged surrounding hardware

This Lid Lock Service Kit replaces the washer lid lock assembly to restore a secure latch and allow normal cycle operation. It helps prevent the lid from opening during spin for safe, reliable use. What it does:

• Replaces a worn or damaged lid lock assembly so the lid secures during spin cycles
• Can resolve symptoms like the washer not starting, stopping mid-cycle, or showing lid-lock related errors
• Restores the mechanical/electrical interface that detects and locks the lid for safe operation
• Works as a direct replacement for the original lid lock components

• Disconnect power to the washer before starting any repairs to avoid electrical shock
• Access and remove the existing lid lock per the parts diagram; handle wiring connectors and fasteners carefully
• Verify proper alignment of the latch and test the lid lock function through a diagnostic or a short test cycle after installation

This lid lock bezel is the molded trim that snaps into the washer's top panel opening and holds the lid lock in place. Replace a cracked or missing bezel to keep the lock secure and ensure consistent lid-closed detection during cycles.

• Secures and aligns the lid lock within the top panel opening
• Covers the cutout for a finished look and protected edges
• Helps prevent the lock from wobbling or falling through the opening
• Common signs of failure: broken/missing bezel, loose lid lock, intermittent "lid open" errors, or cycles that won't start because the lock can't seat

• Disconnect power and water supply before service
• Lift or hinge the top panel per model instructions to access the lock from below
• Detach the lid lock from the underside, release the old bezel tabs, and remove
• Snap in the new bezel, reinstall the lock with proper orientation, and test operation

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This spring-style hose clamp secures flexible appliance hoses to fittings to prevent leaks and hose separation. Replaces worn or damaged clamps to restore a tight, reliable hose connection. What it does

• Holds drain, inlet, or discharge hoses firmly to prevent leaks at fittings
• Stops hoses from slipping off during appliance operation or vibration
• Commonly replaced when rusted, stretched, or visibly damaged
• Helps eliminate intermittent leaks and water pooling under the appliance

• One hose clamp

• Disconnect power and water supply, and drain residual water before starting
• Use pliers to expand the spring clamp for removal and installation
• Ensure clamp sits squarely over the hose and fitting bead for a secure seal
• Replace with the same style and size; do not overtighten or modify the clamp

Includes 12 screws.

The screw is an OEM replacement component for GE dishwashers. It is used to securely fasten parts inside the dishwasher tub assembly.

Causes of a damaged or defective screw usually involve wear from continuous mechanical stresses and vibration during dishwasher usage. Loose parts affect machine balance and performance.

Symptoms of a compromised screw placement include:

• Noises or abnormal sounds coming from inside the tub  
• Intermittent error codes related to moving components
• Detached or misaligned spray arms or filters
• Insecure tub fixtures that can be jarred with normal operation 

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

This bulk replacement hose provides a plain-language replacement for damaged or worn appliance hoses. Use it to restore a secure water connection and stop leaks or restricted flow where the original hose is failing. What it does

• Carries water between components to maintain normal flow
• Replaces cracked, split, or brittle hose sections that can leak
• Helps resolve symptoms like visible leaks, reduced water flow, or pooling near the hose
• Designed for cutting and fitting when a specific hose length is required

• One bulk hose (cut-to-length)

• Cut to the exact length required and secure ends with appropriate clamps or fittings
• Inspect mating fittings and clamps for wear; replace if damaged
• Turn off power and water supply before installation and test connections for leaks after restoring service

A #8-18 x 9/16-inch hex washer head screw used to secure panels and components in appliances. Provides a proper fit for fast, reliable fastening when replacing missing, damaged, or stripped screws. What it does:

• Secures panels, brackets, and trim to keep components aligned and stable.
• Restores proper fastening when threads are stripped, the original screw is missing, or a head is damaged.
• Helps stop rattling or loose parts caused by worn or broken fasteners.
• Fits applications requiring a #8-18 thread with a 9/16" length and hex washer head style.

• Verify thread size, head style, and length before installation.
• Use the correct hex driver or socket to avoid cam-out or head damage.
• Do not overtighten; snug until secure to avoid stripping threads or deforming parts.
• Disconnect power and follow appliance-specific safety steps.

This 8-18 x 3/4 machine screw fastens appliance panels and small brackets to keep components secure and stable. It's a direct-fit replacement screw used where the original hardware has stripped, broken, or gone missing. What it does:

• Secures access panels, mounting brackets, and small assemblies
• Restores proper alignment and reduces rattling or vibration
• Replaces stripped or damaged fasteners
• Keeps wiring and components held in place for safe operation

• Unplug the appliance or disconnect power before starting work
• Use the correct driver and size to avoid stripping the head
• Do not overtighten; snug until secure to prevent damage to parts
• Replace corroded or damaged fasteners for best results

This water inlet valve assembly controls hot, cold, and mixed water flow into the washer. Replacing a failing valve restores proper fill levels and temperatures for reliable wash and rinse performance.

• Directs household water into the tub; blends hot and cold as commanded
• Three solenoids regulate multiple fill circuits/temperatures
• Common failure signs: slow fill, no fill, wrong water temperature, or continuous filling
• May also address leaking at the valve body or water entering when the washer is off

• Unplug washer and shut off water supply before service
• Keep track of hose orientation and wire connectors for reassembly
• Have a towel or shallow pan ready for residual water
• After install, check for leaks and run a test fill cycle

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.