Parts for Ge PTW900BST0WS: Top Panel & Lid Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

The Main Control Board is an OEM part for GE washing machines. As a primary electronic module, it receives inputs from other control boards to regulate all machine functions like cycles, temperatures, motor control, and user interface control. Proper communication between control boards is vital for reliable washing performance.  

Causes of a bad main control board can include water damage over time corroding circuitry, failure of chips or capacitors from continuous operations, or power surges causing shorts.

Symptoms of a bad main control board include:

• Glitchy or unresponsive operations across multiple cycles
• Inability to properly regulate temperatures  
• Communication errors between control modules
• Motor or drain issues indirectly caused by board failures

This genuine GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. Installing an OEM main control board ensures optimized coordination between electronic systems to wash load after load.

8-18 hi/lo 5/8

This screw is a factory fastener used to secure appliance components. Replace a missing, stripped, or corroded screw to keep panels, brackets, and assemblies tight and help prevent vibration or rattling from loose hardware.

• Secures panels, brackets, and internal assemblies at their mounting points
• Replaces lost, rusted, or stripped hardware for a solid, reliable hold
• Helps reduce vibration, rattling, or shifting caused by loose fasteners
• 1/4-20 thread per OEM designation for proper fit where specified

• Disconnect power and, if applicable, shut off water supply before servicing
• Start threads by hand to avoid cross-threading, especially in plastic
• Tighten snugly; do not overtighten to prevent stripping or cracking
• Verify alignment and stability of the secured component after installation

The Ground Screw is an OEM part for GE dryers. It ensures proper grounding and electrical safety for your dryer. This screw securely connects the ground wire to the dryer chassis, providing a path for electrical current to safely discharge in the event of a fault or power surge.

A bad Ground Screw can lead to electrical issues and potential safety hazards. Causes of a bad Ground Screw can include corrosion, loose connections, or damage due to accidental mishandling or improper installation.

Symptoms of a bad Ground Screw include:

• Intermittent dryer operation
• Visible signs of damage or deterioration on the screw or ground wire
• Tripped circuit breakers or blown fuses

Replace your faulty or damaged Ground Screw with this genuine OEM GE part to ensure proper grounding and electrical safety for your dryer. 

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This white top cover restores the washer's finished top surface and helps protect internal components from spills, moisture, and debris. Replace a dented, rusted, or damaged panel to keep the cabinet secure and looking clean.

• Forms the washer's upper cabinet surface and enclosure
• Helps maintain proper fit for lid/trim and overall cabinet rigidity
• Shields internal wiring and mechanisms from debris and splashes
• Common signs: dents or rust on the top, loose/rattling panel, lid/door misalignment, or a missing/broken top

• Disconnect power and turn off water supply before servicing
• Wear cut-resistant gloves; sheet-metal edges can be sharp
• On most models, remove screws/clips securing the top, slide it back, then lift off and transfer any retainers or brackets to the new panel
• Align the new cover and secure fasteners without overtightening

The Thermistor is an OEM part for GE washers. This thermistor monitors and regulates the temperature inside your GE washer during the different cycles.

The thermistor ensures accurate temperature sensing by measuring the temperature of the water or air inside the washer and sends this information to the control board, allowing it to adjust the heating elements or cooling mechanisms accordingly.

A bad thermistor can occur due to wear and tear, exposure to extreme temperatures, or electrical malfunctions. If you notice symptoms such as the washer not heating or cooling properly, error codes indicating a faulty thermistor, or inconsistent temperature readings, it may be time to replace the component.

Symptoms of a bad thermistor include:

• Washer not heating or cooling properly
• Error codes indicating a faulty thermistor
• Inconsistent temperature readings

Restore accurate temperature control by replacing the faulty thermistor with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This lid lock striker attaches to the washer lid and engages the lock mechanism when closed. Replacing a worn striker restores proper lid locking so cycles can start and spin safely.

• Provides the physical tab the lid lock/switch detects to verify the lid is closed
• A damaged or missing striker can cause the lid not to lock, washer not to start or spin, cycle pauses, or a flashing lid lock indicator/error
• Helps ensure the control can safely allow agitation and spin only when the lid is closed
• Restores alignment between the lid and lock to prevent false "lid open" detection

• Disconnect power before servicing; moving parts and electrical components can be hazardous
• Open the lid and note the striker's orientation and position
• Remove the old striker and install the new one using the existing mounting method; do not overtighten
• Close the lid to confirm the lock engages smoothly before running a cycle

The Lid Stanchion is an OEM part for GE washing machines. It securely mounts the washer lid in place through hinges at the top of the cabinet.

Symptoms of a bad lid stanchion include:

• Loose, wobbly, or misaligned washer lid that does not stay flush   
• Gaps visible around lid sealing surfaces allowing air/moisture in
• Grinding or creaking noises heard from the hinge area during the opening

Causes involve worn, stripped, or corroded hinge mounting points from repeated opening/closing cycles over time. Failure risks lid detachment.

This OEM GE replacement lid stanchion ensures safe and stable lid support for proper sealing. Rely on sturdy stanchions to protect against broken lids. Replace yours today for smooth, reliable openings and closings.

Compatible with some Hotpoint, RCA, and Kenmore washers as well, this stanchion maintains critical structural rigidity.

Size: 8 - 18 ab.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This lid lock bezel frames and supports the washer's lid lock on the top panel. Replacing a cracked or missing bezel keeps the lock properly seated and restores a clean, finished appearance around the opening.

• Secures and aligns the lid lock in the top cover opening
• Provides a finished edge and protects the panel around the lock
• Helps prevent the lock from shifting, rattling, or sitting unevenly
• Common signs it's needed: cracked/missing bezel, loose or misaligned lock, visible cosmetic damage

• Disconnect power before servicing.
• Access the lid lock from beneath the top panel; remove fasteners to free the lock, then release the bezel's retaining tabs.
• Seat the new bezel in the opening, reinstall the lock, and ensure the lid closes and locks properly.
• Handle wiring carefully; avoid pulling on the harness.

This is the glass lid assembly for select top-load washers. It restores a clear, secure cover over the tub so the lid lock can engage properly and lets you monitor the wash action through the white-framed glass.

• Covers the wash basket with a hinged, glass-topped lid
• Aligns with the lid lock/strike so cycles can start and continue
• Helps contain splashes and reduce noise from an open/damaged lid
• Replaces a lid that is cracked, shattered, warped, or broken at the hinges
• Typical symptoms: visible cracks or missing pieces, difficulty closing, intermittent lid-lock errors

• Disconnect power and turn off water before servicing.
• If the old lid is cracked, tape the glass to contain fragments; wear cut-resistant gloves and eye protection.
• Support the lid; remove hinge screws and lift the old lid off the top panel.
• Transfer model-specific hardware (hinges, lid strike, screws) from the original as needed, install the new lid, tighten screws evenly, and align/lock operation.

This lid lock and harness assembly restores safe washer operation. It locks the lid during spin and relays lid-closed status to the control, helping resolve no-start/no-spin conditions and a flashing lid-lock light.

• Locks the lid during spin when commanded by the control
• Detects lid position and sends a signal to the control board
• Helps prevent the washer from running with the lid open
• Typical failure signs include the washer not starting or not spinning, cycles pausing mid-cycle, or a blinking lid-lock light/clicking sound

• Unplug the washer before servicing; turn off water if you need to move the unit
• Access the lock by lifting or removing the top panel; remove mounting screws or release tabs
• Route the new harness along the original path and secure in clips; fully seat connectors at the control
• Run a spin test to verify lock/unlock operation

This siphon cap seals and protects a refrigerator drain/siphon opening to help direct water to the drain and reduce leaks or odors. It's a small replacement piece that restores the intended drain seal and routing. What it does:

• Seals the siphon/drain outlet to prevent unwanted water from leaking or pooling
• Helps maintain correct water routing to the drain during defrost and ice/water use
• Reduces chance of odors traveling back from the drain passage
• Addresses symptoms such as water under the appliance, slow draining, or dripping near the drain area

• One siphon cap (exact part as listed)

• High-level replacement; inspect the drain area and surrounding seals before installation
• Ensure the appliance is powered off and water supply is shut at the valve if accessing water components
• Clean the drain opening of debris before seating the new cap for a secure fit
• If damage extends beyond the cap (cracked housing, clogged drain), consider additional service

This dispenser drawer assembly replaces the pull-out detergent drawer on compatible washers. It restores smooth operation and proper dispensing of detergent, bleach, and fabric softener to help prevent leaks, residue build-up, and poor cleaning results.

• Holds and meters detergent, bleach, and fabric softener into the wash at the correct time
• Helps resolve no or incomplete dispensing of additives
• Common fix for a stuck, hard-to-open/close, or cracked drawer
• Can address water leaking or overflowing from the dispenser area

• Disconnect power and turn off water before servicing
• Fully extend the drawer, press the release tab, and remove the old drawer
• Align and slide the new drawer into the rails until it clicks into place
• Run a quick cycle to check for leaks

This 10-32 machine screw fastens small appliance components and replacement assemblies, restoring secure mounting and reliable electrical or panel connections. Its length fits common cabinet, control, and bracket attachments. What it does

• Secures control boards, panels, brackets, and grounding tabs using a 10-32 machine thread
• Replaces stripped or missing mounting screws that allow panels or parts to rattle or shift
• Helps restore stable electrical connections where a threaded fastener is required
• Works where a 1.31 in (approx. 1-5/16 in) long 10-32 screw is specified

• Power off and unplug the appliance before beginning any repair
• Match thread size and length to the original screw; do not force a wrong-size fastener
• Start threads by hand to avoid cross-threading; tighten securely but do not overtighten
• Use appropriate tools and wear eye protection when working on metal assemblies

This lid lock harness clip secures the lid lock wire harness to the washer cabinet or top. It keeps the wiring routed and protected to help prevent chafing, snagging, and intermittent lid-lock performance issues. What it does / common symptoms:

• Holds the lid lock wire harness in place along the cabinet/top
• Maintains proper routing to avoid pinching or rubbing on moving parts
• Reduces vibration-related wear on the wiring
• Symptoms of a failed/missing clip: loose or dangling harness, scuffed insulation, intermittent lid-lock response

• 1 lid lock wire harness clip

• Disconnect power before servicing
• Access the lid lock wiring path (lift top/remove console as required by your model)
• Release the old clip from the panel and harness; snap the new clip into the mounting hole and secure the harness
• Ensure the harness has adequate slack and is not pinched before restoring power

This is a self-tapping Plastite screw with a hex washer head and a 5/8 in. length that secures plastic and thin-sheet components. Use it to replace missing or damaged mounting screws for a snug, reliable fit. What it does:

• Forms threads in plastic (Plastite style) to fasten panels, brackets, and trims.
• Hex washer head provides a larger bearing surface for better holding power.
• Replaces stripped, corroded, or missing screws to stop loose or rattling parts.
• Works where a self-tapping screw is required for secure mounting without a separate nut.

• Use the correct hex/nut driver and a properly fitting bit to avoid stripping the head.
• Hand-start the screw and drive straight to prevent cross-threading; stop when snug—do not overtighten into plastic.
• Unplug the appliance or shut off power before disassembling or working near electrical components.
• Replace with the same screw type and size to maintain proper fit and function.

The Water Inlet Valve Seal is an OEM part for GE washing machines, designed to ensure a watertight seal around the water inlet valve. This part helps prevent leaks by sealing the connection between the water inlet valve and the washing machine's internal tubing. 

Causes of a bad water inlet valve seal include normal wear and tear, exposure to hard water minerals that can erode the seal, and improper installation that may strain or damage the seal.

Symptoms of a bad Water Inlet Valve Seal include:

• Water leaking from the back or underside of the washing machine
• Visible signs of wear or damage to the seal
• Unexplained increase in water usage or utility bills, which may indicate a slow leak

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Water Inlet Valve is an OEM part for GE washing machines. It is responsible for controlling the entry of hot and cold water into the washing machine. This valve opens and closes at the appropriate times during the wash cycle to allow water to enter based on the selected temperature and wash settings.

Causes of a bad water inlet valve include mineral deposits from hard water, which can block the valve, and wear and tear from regular use, which can cause the valve to fail mechanically or electronically. Additionally, if the screens that filter the water before it enters the valve become clogged, water flow can be restricted, affecting the washing machine’s performance.

Symptoms of a malfunctioning water inlet valve include:

• The machine not filling with water.
• Water entering the machine slowly.
• Water leaking around the valve area.
• A noisy valve during operation.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.