Troy-Bilt Edger Parts

This is a genuine replacement oil plug that is found in certain trimmers, edgers, and blowers designed for outdoor use. The oil plug is used to seal and fill the oil in the engine. This part is a high-quality plastic piece that features threads for screwing it into place and an O-ring to create a strong seal to prevent leaks and ensure optimal engine pressure. The oil cap may become stripped or damaged over time, or the O-ring could become faulty. In either case, replacing the entire cap/plug is the easiest solution.This genuine OEM replacement oil plug is compatible with machines from Troy-Bilt, MTD, Yard-Man, Yard Machines, and Cub Cadet. The plug is sold individually and comes with the O-ring. There are no other parts or hardware included. No tools are required to replace this plug. Simply unscrew the old one and screw the new one into place once the O-ring has been put on the new plug. Wear gloves whenever engine work is being performed to ensure hand protection. The oil should be checked regularly in all machines, which is a good time to check the cap to ensure it isn't damaged or in need of replacement.

Starter spring for gas line trimmers. Installs inside the starter assembly to enable recoil operation. Replace if broken, detached, or worn out.

Idler pulley assembly for edgers. Mounts to the deck and maintains proper belt tension. Replace if pulley is cracked, worn, or spins roughly.

Carburetor assembly for edgers and gas trimmers. Mixes fuel and air for combustion. Replace if cracked, damaged, or leaking to restore proper operation.

This short block assembly is a genuine MTD part, sold individually. This short block assembly can be used as a replacement part for a string trimmer, a tiller, or an edger. The short block includes the crankshaft, piston, rod, camshaft, valves, and governor. A short block assembly might be necessary if there is damage to a wide range of parts in the equipment's engine. Check for frequent stalling, misfires, or an inability to power on. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer, and it is sold individually. This short block assembly is compatible with the following brands: MTD, Craftsman, and Cub Cadet.

Replacement fuel cap for lawn tractors, trimmers, blowers, and tillers. Prevents fuel leaks and evaporation. Replace if cracked, broken, or missing.

This is a replacement belt that can be used on select edger/trimmer models of lawn and garden equipment. This is the main drive belt that is responsible for driving the trimmer blades. Belts are made of rubber and exposed to constant and repetitive motion, which can cause them to stretch or wear out over time. Eventually, they may become so loose or damaged that they will not be able to drive the blades and will need to be replaced. Without a properly functioning drive belt, the trimmer blades will not work. A genuine replacement part like this provides an exact fit for compatible units. This OEM drive belt is manufactured by MTD and can be used with select models of trimmers from the brand and a few models from Troy-Bilt, as well. This belt is sold as an individual unit and does not include any additional components or hardware. In order to replace the drive belt, a set of wrenches is required. It is advised to clean the pulleys before installing the new belt to ensure optimal performance and extend the life of the belt. Be sure to disengage the engine and wear gloves when replacing this belt or other internal parts.

Spindle pulley attaches to the drive belt and blade assembly in edgers. Replace if pulley is cracked, worn, or damaged to restore proper belt tension.

Skid shoe that mounts to the bottom of your snow blower housing. Replace if cracked, bent, worn down, or missing to protect the auger housing surface.

This blade retainer kit is designed for use with string trimmers and edgers by many manufacturers. It comes with a metal retaining washer that is used with the blade, as well as the needed spool cutting heads. This kit also includes the nut needed to fasten the blade to the gearcase. It is used to install a blade onto the trimmer while adding stabilization through the nut. The parts in the blade retainer kit can become worn out during use and may need to be replaced.When the blade needs to be replaced or a part of the blade retainer kit is broken, removing the parts is required. Moving the blade involves turning the retaining bolt while the equipment is on a level surface. Next, undo the bolt holding the blade so it can be removed. The blade can be replaced at this time, as well as the parts from this blade retainer kit.This blade retainer kit is made for edgers and string trimmers manufactured by Yard-Man, Craftsman, Bolens, Ryobi, MTD, Troy-Bilt, and Yard Machines. It is a single retainer kit that comes as a genuine OEM replacement part sourced directly from the manufacturer.

This air filter is the replacement part for specific tillers, edgers, and cultivators. Its main function is to prevent grime and debris from reaching the engine and carburetor. With time and use, air filters get dirty and may become clogged or damaged. Replacing the air filter regularly encourages adequate air flow to the engine, which reduces engine wear, and increases the longevity of the machine. Replacement is simple and can be done in a matter of minutes. With a screwdriver, remove the old air filter, and install this new, clean filter. Be sure to check the owners manual for proper installation techniques, as it varies by brand and machine. This air filter, made of foam, is a genuine OEM part. It is sold as an individual unit. It is compatible with tillers, edgers and cultivators made by the Ryobi, Troy-Bilt, and Yardman brands. All engines need regular care and maintenance to perform optimally. To ensure the Tiller, Edger, or Cultivator model starts easily, maintains power, functions properly, and has a long, hard-working life, the air filter should be replaced routinely.

Rope won't retract after pulling? This recoil starter spring restores proper rope tension in lawn equipment engines. Essential starter assembly component.

The lock nut is a piece of standard hardware that may have a variety of applications on lawn and garden equipment, including on engines, housings, and other components. The lock nut offers a secure fit by tightening into a flange that prevents the nut from loosening like a regular nut might. Over time, the flange or the nut can become worn or damaged. In some cases, lock nuts may be lost during the process of other repairs or maintenance. Replacing them with genuine OEM parts like this lock nut is the best solution. This lock nut is compatible with hundreds of machines, including mowers, snowblowers, and chippers from MTD, Troy-Bilt, Cub Cadet, RYOBI, Yard-Man, Yard Machines, Bolens, and Husky. The ¼-inch lock nut has multiple locations and applications, so owners should consult their parts diagram for exact placement and part number identification. This lock nut is made of durable metal and sold as a single unit. Those who need additional pieces will have to order multiple quantities. This part will require a wrench or a socket to replace, as well as pliers and/or a screwdriver to hold the bolt or screw in place.

Here is a replacement shoulder screw that is commonly used for various types of outdoor power equipment. Another name for the shoulder screw is a shoulder pin. The screw is often used to help secure the plastic wheels to the deck of a machine. However, different machines may have different uses for shoulder screws and other types of hardware. The shoulder screw is made from metal and is durable. However, the pin may still need to be replaced at some point. Whether it is because of corrosion or being bent, it is important to replace a failed screw with a new one. When performing maintenance on the machine, it is also possible that the screw could become lost, which would require a replacement. This is a genuine OEM replacement shoulder screw. It is sold individually and works with many types of makes and models. The screw is often used for edgers, snowblowers, lawn mowers, and chainsaws. Brands that have models that will be compatible with the shoulder screw include Craftsman, Toro, Cub Cadet, Troy-Bilt, Yard Machines, MTD, Huskee, Yard-Man, and MasterCut.