Troy-Bilt Edger Parts

This short block assembly is a genuine MTD part, sold individually. This short block assembly can be used as a replacement part for an edger. The short block assembly comes with the short block as well as all of its necessary components and fasteners required to replace a damaged short block.If the engine is not starting, is hard starting, or is performing unevenly, the short block may need to be replaced. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer. It is sold individually. This short block assembly is compatible with the following outdoor appliance brands: MTD and Craftsman.

This short block assembly is a genuine MTD part, sold individually. This short block assembly can be used as a replacement part for a string trimmer, a tiller, or an edger. The short block includes the crankshaft, piston, rod, camshaft, valves, and governor. A short block assembly might be necessary if there is damage to a wide range of parts in the equipment's engine. Check for frequent stalling, misfires, or an inability to power on. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer, and it is sold individually. This short block assembly is compatible with the following brands: MTD, Craftsman, and Cub Cadet.

Replacement fuel cap for lawn tractors, trimmers, blowers, and tillers. Prevents fuel leaks and evaporation. Replace if cracked, broken, or missing.

This is a replacement belt that can be used on select edger/trimmer models of lawn and garden equipment. This is the main drive belt that is responsible for driving the trimmer blades. Belts are made of rubber and exposed to constant and repetitive motion, which can cause them to stretch or wear out over time. Eventually, they may become so loose or damaged that they will not be able to drive the blades and will need to be replaced. Without a properly functioning drive belt, the trimmer blades will not work. A genuine replacement part like this provides an exact fit for compatible units. This OEM drive belt is manufactured by MTD and can be used with select models of trimmers from the brand and a few models from Troy-Bilt, as well. This belt is sold as an individual unit and does not include any additional components or hardware. In order to replace the drive belt, a set of wrenches is required. It is advised to clean the pulleys before installing the new belt to ensure optimal performance and extend the life of the belt. Be sure to disengage the engine and wear gloves when replacing this belt or other internal parts.

Spindle pulley attaches to the drive belt and blade assembly in edgers. Replace if pulley is cracked, worn, or damaged to restore proper belt tension.

Idler pulley for gas line trimmers and wheeled trimmers. Guides and tensions drive belts. Replace if worn, cracked, or causing belt misalignment.

This replacement part is a flywheel combo. This is a genuine replacement part made by MTD. This part is a flywheel connected to a pulley. The combination makes it an important part of many engines and is used to transfer forces to different objects so that the user may operate the machine properly during use. A new flywheel combo might be needed if the current one is no longer working. If the pulley area of this part has been stripped down due to friction, it would be a good idea to replace the flywheel combo. Be sure the engine is turned off before replacing this part to prevent injury during the repair. This is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer.

Skid shoe that mounts to the bottom of your snow blower housing. Replace if cracked, bent, worn down, or missing to protect the auger housing surface.

This blade retainer kit is designed for use with string trimmers and edgers by many manufacturers. It comes with a metal retaining washer that is used with the blade, as well as the needed spool cutting heads. This kit also includes the nut needed to fasten the blade to the gearcase. It is used to install a blade onto the trimmer while adding stabilization through the nut. The parts in the blade retainer kit can become worn out during use and may need to be replaced.When the blade needs to be replaced or a part of the blade retainer kit is broken, removing the parts is required. Moving the blade involves turning the retaining bolt while the equipment is on a level surface. Next, undo the bolt holding the blade so it can be removed. The blade can be replaced at this time, as well as the parts from this blade retainer kit.This blade retainer kit is made for edgers and string trimmers manufactured by Yard-Man, Craftsman, Bolens, Ryobi, MTD, Troy-Bilt, and Yard Machines. It is a single retainer kit that comes as a genuine OEM replacement part sourced directly from the manufacturer.

Fastener screw for tillers and lawn equipment. Secures components together for stable operation. Replace if stripped, missing, or damaged during maintenance.

Rotating trimmer head for gas line trimmers and weed wackers. Replace when cracked, worn, or no longer spinning properly during operation.

Rope won't retract after pulling? This recoil starter spring restores proper rope tension in lawn equipment engines. Essential starter assembly component.

Hex lock nut secures bolted joints on outdoor lawn equipment. Replace if threads are stripped, nut is missing, or won't hold proper tension.

The lock nut is a piece of standard hardware that may have a variety of applications on lawn and garden equipment, including on engines, housings, and other components. The lock nut offers a secure fit by tightening into a flange that prevents the nut from loosening like a regular nut might. Over time, the flange or the nut can become worn or damaged. In some cases, lock nuts may be lost during the process of other repairs or maintenance. Replacing them with genuine OEM parts like this lock nut is the best solution. This lock nut is compatible with hundreds of machines, including mowers, snowblowers, and chippers from MTD, Troy-Bilt, Cub Cadet, RYOBI, Yard-Man, Yard Machines, Bolens, and Husky. The ¼-inch lock nut has multiple locations and applications, so owners should consult their parts diagram for exact placement and part number identification. This lock nut is made of durable metal and sold as a single unit. Those who need additional pieces will have to order multiple quantities. This part will require a wrench or a socket to replace, as well as pliers and/or a screwdriver to hold the bolt or screw in place.