Troy-Bilt Edger Parts

This replacement part is an ignition coil. This is a genuine replacement part made by MTD. This part is commonly found in line trimmers or edgers. This part ensures that the trimmer is able to start and stop according to the user's needs.A new ignition coil might be needed if the starting and stopping functions in the line trimmer are not working as effectively as during prior uses. This can be due to a faulty ignition coil, and if this is the case, it should be replaced. Be sure the engine is completely turned off before attempting to replace this part. Refer to the proper user manual for more information on this repair. This is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer.

Idler pulley assembly for edgers. Mounts to the deck and maintains proper belt tension. Replace if pulley is cracked, worn, or spins roughly.

Carburetor assembly for edgers and gas trimmers. Mixes fuel and air for combustion. Replace if cracked, damaged, or leaking to restore proper operation.

This short block assembly is a genuine MTD part, sold individually. This short block assembly can be used as a replacement part for an edger. The short block assembly comes with the short block as well as all of its necessary components and fasteners required to replace a damaged short block.If the engine is not starting, is hard starting, or is performing unevenly, the short block may need to be replaced. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer. It is sold individually. This short block assembly is compatible with the following outdoor appliance brands: MTD and Craftsman.

This short block assembly is a genuine MTD part, sold individually. This short block assembly can be used as a replacement part for a string trimmer, a tiller, or an edger. The short block includes the crankshaft, piston, rod, camshaft, valves, and governor. A short block assembly might be necessary if there is damage to a wide range of parts in the equipment's engine. Check for frequent stalling, misfires, or an inability to power on. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer, and it is sold individually. This short block assembly is compatible with the following brands: MTD, Craftsman, and Cub Cadet.

Spindle pulley attaches to the drive belt and blade assembly in edgers. Replace if pulley is cracked, worn, or damaged to restore proper belt tension.

Idler pulley for gas line trimmers and wheeled trimmers. Guides and tensions drive belts. Replace if worn, cracked, or causing belt misalignment.

This replacement part is a flywheel combo. This is a genuine replacement part made by MTD. This part is a flywheel connected to a pulley. The combination makes it an important part of many engines and is used to transfer forces to different objects so that the user may operate the machine properly during use. A new flywheel combo might be needed if the current one is no longer working. If the pulley area of this part has been stripped down due to friction, it would be a good idea to replace the flywheel combo. Be sure the engine is turned off before replacing this part to prevent injury during the repair. This is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer.

Skid shoe that mounts to the bottom of your snow blower housing. Replace if cracked, bent, worn down, or missing to protect the auger housing surface.

This blade retainer kit is designed for use with string trimmers and edgers by many manufacturers. It comes with a metal retaining washer that is used with the blade, as well as the needed spool cutting heads. This kit also includes the nut needed to fasten the blade to the gearcase. It is used to install a blade onto the trimmer while adding stabilization through the nut. The parts in the blade retainer kit can become worn out during use and may need to be replaced.When the blade needs to be replaced or a part of the blade retainer kit is broken, removing the parts is required. Moving the blade involves turning the retaining bolt while the equipment is on a level surface. Next, undo the bolt holding the blade so it can be removed. The blade can be replaced at this time, as well as the parts from this blade retainer kit.This blade retainer kit is made for edgers and string trimmers manufactured by Yard-Man, Craftsman, Bolens, Ryobi, MTD, Troy-Bilt, and Yard Machines. It is a single retainer kit that comes as a genuine OEM replacement part sourced directly from the manufacturer.

Fastener screw for tillers and lawn equipment. Secures components together for stable operation. Replace if stripped, missing, or damaged during maintenance.

Rotating trimmer head for gas line trimmers and weed wackers. Replace when cracked, worn, or no longer spinning properly during operation.

Rope won't retract after pulling? This recoil starter spring restores proper rope tension in lawn equipment engines. Essential starter assembly component.

Flange bearing for lawn tractors and snow blowers. Replace if you notice excessive noise, vibration, or rough wheel rotation. Verify fit with your model.

A ball bearing is a common type of rolling-element bearing. It will use balls to keep space between the bearing races and eliminate friction and contact between moving parts. Ball bearings used in lawn and garden equipment ensure that axial loads and radial loads are evenly supported and that there is only a limited amount of rotational friction on the component. It distributes weight evenly, but will undergo constant wear and tear from vibration, heat, and friction and will need replacement regularly. This ball bearing is a genuine OEM part suited to use in Craftsman, Cub Cadet, Ryobi, Troy-Bilt, MTD, Huskee, Yard Machines, Bolens, Mastercut, and Yard-Man equipment. It may be needed for repair work done on a lawnmower, snowblower, tiller, edger, or a log splitter.