Troy-Bilt Leaf Blower Parts

Replacement fuel cap assembly for tillers and outdoor power equipment. Seals fuel tank, prevents debris entry, and features vent slots. Needed when original cap is cracked, broken, or gasket is worn.

Spring roll pin fastener for lawn mowers and outdoor power equipment. Secures components in place. Replace if missing, worn, or damaged during repairs.

This is a genuine wing nut replacement designed for use in select walk-behind lawn mowers. Although some wing nuts are considered standard hardware on lawn mowers and other equipment, this specific wing nut connects to a bolt and secures the front baffle to the deck of the mower. Over time, this plastic wing nut can crack, fall off, or the threads may become damaged. This will result in the mover assembly being affected and the unit may not be able to be used until the nut has been properly replaced. This genuine replacement part will provide the exact fit for compatible mowers. This genuine OEM wing nut is manufactured to exact standards and comes from MTD. It can be used with hundreds of walk-behind lawn mower models from the brand, as well as those from Cub Cadet, Ryobi, Troy-Bilt, Bolens, Yard Man, Yard Machines, and Huskee. This plastic wing nut is sold individually. The carriage bolt that it connects to will need to be purchased separately if that also needs to be replaced. No tools are required for this installation, as it can simply be hand-tightened into place. Wear gloves for hand protection when performing equipment repairs.

Protective cover that secures over the air filter on gas line trimmers and leaf blowers. Replace if cracked, broken, or missing to keep debris out.

This carburetor O-ring creates an airtight seal between carburetor components to prevent fuel and air leaks in small engines. It maintains proper fuel mixture and prevents contamination that could affect engine performance. Replace it when you notice fuel leaks around the carburetor, poor engine performance, or difficulty starting your equipment.

Hex flange bearing supports rotating shafts in riding mowers and tractors. Replace when you notice grinding noise or rough rotation. Verify fit with your model.

The shoulder screw is used in places where a spacer or bearing surface is needed, since the top half of the screw is unthreaded. These fasteners are often used for guides, pivot points, mounting pins, axles, and even a shaft for bearings and bushings in various MTD engines. With regular use, the screws can wear down or be lost. Always repair the missing hardware promptly with genuine OEM replacements. Disengage the spark plug and wear gloves when performing work on engines for safety. This genuine OEM replacement shoulder screw has been designed to be compatible with machines from MTD, Troy-Bilt, Yard-Man, Yard Machines, Bolens, Cub Cadet, and Craftsman. It can be used for multiple applications and in multiple locations in different models of lawnmowers, tractors, and chippers that use the screw in various applications. Check your parts diagrams for the exact location and use of these screws before ordering. This is sold as an individual unit; order multiple quantities as needed.

This is a flange nut that can be used in a variety of lawn and garden equipment from different manufacturers. The nut is made of metal, measures 5/16x18, and is used to secure components in place. It also assists with preventing backing out caused by vibration. Over time, the flange nut can become damaged and will need to be replaced. If the flange nut in lawn and garden equipment has become damaged, is loose, or gets lost, then replacement is required. The level of difficulty of replacing a flange nut depends on which parts it's securing and what kind of equipment it is installed on. This flange nut is an OEM replacement part that can be used with lawn mowers, snowblowers, wood chippers, tillers, log splitters, leaf blowers, and edgers by MasterCut, Craftsman, Yard-Man, Toro, Bolens, Cub Cadet, Montgomery Wards, Ryobi, Huskee, Troy-Bilt, MTD, and Yard Machines. It is sold individually and will require a wrench or socket for installation.

Flange bearing restricts movement and prevents shifting in lawn tractor components. Replace if you notice wobbling or unusual noise. Verify fit with your model.

This is a genuine ignition module, also known as an ignition coil, that is designed to be used on select line trimmers. The ignition module is what connects the spark plug to the machine and is responsible for creating the spark and carrying that power back to the engine to power the unit. if the ignition module fails, the engine will not be able to start. It could start and stop, or it could fail to start entirely. Either way, replacing the ignition module will resolve the issue in most cases and can be done with this OEM part. Since it's attached to the spark plug, it's a good idea to inspect the module during regular spark plug replacement and other maintenance to check for damage. The ignition module is made from durable metal and rubber materials and is sold as an individual part. It will require a screwdriver and socket set to replace the part. Be sure to wear gloves to protect the hands and disconnect the power for safety before doing any work on electrical components like this.

This genuine MTD replacement part is a crankcase cover O-ring for use with trimmers, blowers, tillers, edgers, string trimmers, and cultivators. A properly functioning O-ring is essential for the safe and reliable use of the equipment. The crankcase houses the crankshaft, and the O-ring is used to ensure a seal on the case. A damaged or worn out O-ring may cause oil to leak, leading to unsafe operation. The O-ring may become worn out or damaged with extended use, necessitating replacement. Remember to check the O-ring periodically to spot any wear or damage. This part is an identical replacement for an O-ring that is missing, worn out, or damaged. Prior to working with this part, please refer to the original product manual for installation instructions. Additional tools may be required for installation of this part. For safety, always wear gloves and ensure unit is powered down prior to performing any installation or repair.This high quality OEM replacement part is sourced directly from the manufacturer, and it is sold individually. This part is compatible with a variety of Craftsman, Cub Cadet, Troy-Bilt, Yard Machines, MTD, and more trimmers, blowers, tillers, edgers, string trimmers, and cultivators.

Flywheel assembly for tillers and outdoor power equipment. Replaces cracked, damaged, or worn flywheels that affect engine timing and cooling fan operation.

This gasket is a genuine MTD part. It is an insulator gasket meant as a replacement part on tillers, string trimmers, leaf blowers, edgers, and cultivators. The insulator gasket seals the connection between the insulator and cylinder. This gasket is made of durable, heat-resistant plastic. To replace the insulator gasket, a pair of work gloves, wrench, and screwdrivers are necessary. This gasket is a genuine OEM part sourced directly from the manufacturer. It is sold individually. It is compatible with machines made by Craftsman, Cub Cadet, MTD Pro, Troy-Bilt, Yard Machines, and Yard-Man.

This replacement part is an ignition coil. This is a genuine replacement part made by MTD. This part is commonly found in line trimmers or edgers. This part ensures that the trimmer is able to start and stop according to the user's needs.A new ignition coil might be needed if the starting and stopping functions in the line trimmer are not working as effectively as during prior uses. This can be due to a faulty ignition coil, and if this is the case, it should be replaced. Be sure the engine is completely turned off before attempting to replace this part. Refer to the proper user manual for more information on this repair. This is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer.

This is a genuine replacement oil plug that is found in certain trimmers, edgers, and blowers designed for outdoor use. The oil plug is used to seal and fill the oil in the engine. This part is a high-quality plastic piece that features threads for screwing it into place and an O-ring to create a strong seal to prevent leaks and ensure optimal engine pressure. The oil cap may become stripped or damaged over time, or the O-ring could become faulty. In either case, replacing the entire cap/plug is the easiest solution.This genuine OEM replacement oil plug is compatible with machines from Troy-Bilt, MTD, Yard-Man, Yard Machines, and Cub Cadet. The plug is sold individually and comes with the O-ring. There are no other parts or hardware included. No tools are required to replace this plug. Simply unscrew the old one and screw the new one into place once the O-ring has been put on the new plug. Wear gloves whenever engine work is being performed to ensure hand protection. The oil should be checked regularly in all machines, which is a good time to check the cap to ensure it isn't damaged or in need of replacement.