Troy-Bilt Parts

The front-drive wheels are attached to the axle with a ring gear and a left-hand smaller gear inside. The wheels are responsible for keeping the mower deck from touching the ground and keeping the blade at a good height for safe operation. They also provide easy maneuvering of the lawnmower. The black and white finish offers a clean, classic look. Although wheels don’t typically wear down enough to need to be replaced, they can become damaged over time. If the wheels are broken or missing, this replacement from the manufacturer can get a lawn mower rolling again in no time at all. Although it’s not required, it is suggested to replace wheels in pairs to ensure even wear over the lifespan of the mower. The front-drive wheel is compatible with several MTD and Troy-Bilt lawnmowers that require front drive wheels. This wheel is typically for self-propelled models. This item is sold as a single unit and additional wheels will have tobe purchased separately. These sturdy plastic wheels are direct from the manufacturer and made to their exact standards to guarantee proper performance and fit with every compatible model.

These O rings are replacement parts intended for use in a number of gasoline-powered lawn trimmers. The O rings serve as gaskets and are placed at the entry and exit points in the carburetors where gasoline and air are mixed and the expansion powers the trimmer. Though constructed of durable material, periodically the flow of the air/fuel mix or the rush of expanding air will cause damage to occur to the O rings so they become less resilient and the carburetor functions less efficiently. In these cases, users often decide to replace not just the element of the carburetor but the O rings as well. Users may notice problems with the carburetor when they cannot get an adequate adjustment, allowing the trimmer to function smoothly. They may also have trouble getting the trimmers to start at all or run without smoking. To replace the O rings, remove the air filter cover and carburetor. Once the carburetor has been cleaned, and the gasket and filter replaced, add a fresh mix of 40:1 fuel. The trimmer should start immediately. These OEM certified O rings are compatible with Bolens, Troy-Bilt, Yard Machines, and Craftsmen trimmers.

A bump head knob is a part of a string trimmer. When the trimmer is tapped against the ground or any hard surface, it will let out more line. This component, which is primarily made from rubber, is also responsible for securing the spool to the trimmer head. Over time, a bump knob can break. If it is damaged, the trimmer won't release more lines. It is easy to install a brand-new bump head knob replacement. First, get a screwdriver and unscrew the old bump knob. Grab the replacement and screw it to the trimmer head. Tighten it for a secure fit. This replacement only comes with a bump head knob. It doesn't have other string trimmer replacement parts. For an efficient, compatible part replacement, choose this MTD 791-153066B Bump Head Knob. You can use it with string trimmer models made by MTD, Bolens, Yard-Mad, Yard Machines, Craftsman, Troy-Bilt, and Ryobi. It is a genuine OEM part that is sold individually.

The friction wheel for a snowblower is sometimes also known as a friction disc or a friction ring. The friction wheel is what helps to move the snowblower forward. When the disc is in contact with the spinning drive wheel, the disc will rotate and turn the axle to propel the snowblower. Over time, the friction wheel can start to wear down or even break. If this happens, it will mean that the snowblower will move slowly, or that it might have erratic movements. Owners who find that they are having similar problems with their machine will want to check the friction wheel to see if it is damaged or broken. They will need to replace the disc before they can use the machine efficiently and safely. The genuine OEM replacement friction wheel is for use with snowblowers, and it is sold individually. Compatible brands include Cub Cadet, Craftsman, Troy-Bilt, Yard-Man, Montgomery Wards, Bolens, Huskee, MTD, Yard Machines, and Ryobi.

This blade adapter is made to attach a lawn mower cutting blade to the drive shaft of a push mower. Though it is made of sturdy metal and is tightly fastened to the mower's drive, the adapter and blade may wear and loosen over time. This can present a dangerous situation as well as poor cutting performance for the blade. Also, each adapter has a small insert tab that fits into the blade attachment. This tab, called a “key,” is actually a shear pin. Should the blade strike a solid object, the key will sheer off, preventing the blade from coming loose or suffering irreparable damage. The solution to either of these problems is to replace the blade adapter. The blade itself should be closely examined to make sure it fits the new adapter with no wobble or slack. To replace the blade adapter, turn the mower on its side with the air filter on top. Use a ratchet to remove the bolt that attaches the blade and adapter to the drive shaft. Make certain to fit the new adapter key into the keyway on the shaft. Always use a replacement part like this one, that is OEM certified to be identical to the original. This blade adapter is compatible with Ryobi, Yard Machines, Yard Man, Huskee, Cub Cadet, Troy-Bilt, MTD, and Bolens mowers.

This is a genuine replacement bolt that is designed specifically for use on select lawn tractors. This tractor bolt is a specialty piece of hardware designed for use on the steering segment gear. This screw holds the gear in place and is exposed to constant vibrations and repetitive motion as a result. Over time, that can result in damage, wear, or even total breakage of the bolt and require a replacement. If the bolt isn't functional or is missing, the steering segment gear will not be secured and that can lead to further damage if left unattended. Using a genuine replacement part like this will guarantee an exact fit for compatible models. This genuine OEM gear bolt is manufactured by MTD. It is compatible with lawn and garden equipment from RYOBI, HUSKEE, Troy-Bilt, Bolens, Yard Machines, Yard Man, and Cub Cadet, along with select models from MTD. The bolt works for more than 100 compatible models. It is made of durable metal and sold as an individual unit. A wrench or socket will be required to replace this part. Always wear gloves when performing repairs on lawn and garden equipment and allow the engine to cool before doing any work.

This fuel tank assembly from MTD is a genuine replacement part. It is a fuel reservoir made from a thick and durable plastic material. It is designed to fit and work with tillers, edgers, and string trimmers from MTD, Craftsman, Cub Cadet, and Yard Machines. When this fuel tank wears out, liquid may seep out and waste gas. A fuel tank assembly replacement is easy. The process will take approximately 30 minutes or less. First, make sure that the machine has cooled down and there is little fuel left in the tank. Make sure to wear gloves since fuel spills can occur, especially when removing the fuel lines. Then, remove the spark plug connector to prevent the engine from starting. Disconnect the fuel line and unfasten the mounting screws of the fuel tank. Install the fuel tank and attach the fuel line. This replacement fuel tank assembly is sold individually. The assembly includes the tank, fuel cap, and one fuel line. It is an original replacement made directly by MTD.

This genuine OEM replacement auger bearing flange fits a wide range of snowblowers. The auger is the part of a snowblower that scoops up and moves it away from the area being cleared. It is held in place by a bearing, and this flange connects to the bearing to reduce friction and motion. This flange helps prevent grinding, which would degrade the bearing and cause the auger to stop working effectively. Bearings and flanges receive a lot of wear and tear because they are built to absorb friction. Over the natural course of an appliance's life, bearings and flanges will normally wear down and need replacing. If a bearing flange snaps, the auger will no longer turn, and the snowblower will not move snow. To replace a bearing flange, use a socket wrench to gain access to the belt cover and then detach the auger housing. Remove the pulley and thread, then take the auger out of its housing. Pull out the old auger bearing flange and install the new part. This part is compatible with Yard Man, Troy-Bilt, Craftsman, Bolens, MTD, Huskee, and Yard Machines snow blowers. It comes sourced from the original manufacturer and ships individually.

This OEM replacement push cap can be used in a variety of lawn and garden equipment. The push cap is secured to the end of a shaft, providing protection to the user from the sharp metal edge of the shaft. The push caps that are included with the machines may wear out over time or fall off in some cases, creating an injury risk involving sharp metal edges. These push caps are high-quality and made from durable plastic. They are easy to install. The OEM push cap is a genuine part made by the original manufacturer, to ensure quality and s proper fit. The push caps can be used on lawn tractors, chippers, shredders, log splitters, and other equipment. Some of the brands that this push cap is compatible with include MTD, Husky, Yard-Man, Bolens, Troy-Bilt, Ryobi, Yard Machines, and cub Cadet.

This is a chute flange keeper that is commonly used on snowblowers. It is black and made of durable plastic. The purpose of the chute flange keeper is to ensure the chute can properly rotate along with the chute adapter. The chute flange keeper is connected to the flange on the chute. There are typically three chute flange keepers on a snowblower.If a chute flange keeper is damaged, broken, or missing, it will need to be replaced. A screwdriver and work gloves will be needed to handle the job. A screwdriver can be inserted into the equipment to pry off the old chute flange keeper. Put the new flange keeper in place and force it into position using vice grips. Users can also snap in one end and use a pair of pliers to get the other side to fit. Reassemble all parts before using the tool again.This is an authentic OEM replacement part that is sourced directly from the manufacturer. It is sold as an individual component. The chute flange keeper is designed for use with snowblowers manufactured by Yard-Man, Huskee, MTD, Yard Machines, Troy-Bilt, Cub Cadet, and Craftsman.

This bearing flange is used on a wide variety of lawnmowers and lawn tractors. Unlike other bearings, the flange bearing is used to ensure the axle assembly stays securely attached to the pivot axle. The purpose of the flange bearing is to make sure the axle is able to move freely and in an effortless manner. The bearing undergoes a large amount of friction and stress while in use, so it can start to wear down.If the lawnmower is showing signs of wear at the flange bearing, it should be replaced. It's a good idea to regularly inspect the part to be sure it is in good shape. To replace the flange bearing, remove the bolt from the steering shaft and remove the old bearing. Grease the new bearing and the shaft before reinstalling the part. Reassemble and tighten all parts.This is a genuine OEM replacement part that is directly sourced from the manufacturer. It is sold as an individual component. The flange bearing is made to be compatible with lawnmowers created by MasterCut, Yard-Man, Bolens, Huskee, MTD, Yard Machines, Murray, Troy-Bilt, Cub Cadet, and Craftsman.

This control handle is designed specifically as a replacement for use on select walk-behind lawn mowers. The control handle is the safety that is engaged to allow the engine to run. When holding the control handle in, the pull start can be activated and the engine will run. Once the control handle is released, the engine will stop. In the event that the control handle becomes damaged or fails, it will need to be replaced so that the mower can continue to be used. This handle can provide a genuine replacement for compatible models. This control handle is manufactured to exact standards by MTD and provides an exact fit. It is compatible with hundreds of models, including select models from RYOBI, Yard Machines, Troy-Bilt, Yard-Man, Husky, Bolens, and Cub Cadet. This part is also known as the control bar, control handle, engine stop handle, bail control, or mower bail. It is made of durable metal and sold individually. No tools are required for the installation of this part. To replace the handle, simply squeeze the existing control handle to remove it from the outer handle, and then align the new handle and slide it into place. When properly installed, the pressure will hold it in place and allow for proper operation.

The Clutch Assembly is an OEM part for MTD outdoor power equipment. This assembly is used in various lawn and garden machines to engage and disengage the power from the engine to the drive mechanism, allowing for controlled operation of the equipment.

Causes of a bad clutch assembly can include wear and tear from regular use, exposure to extreme temperatures, or damage due to improper handling or maintenance. A malfunctioning clutch can lead to poor performance and control of the equipment.

Symptoms of a bad clutch assembly include:

• Difficulty in engaging or disengaging the drive mechanism
• Slipping or jerky movements during operation
• Unusual noises when the clutch is engaged
• Loss of power transmission from the engine to the drive components

This MTD replacement part is also compatible with other brands and models within the MTD family, ensuring a wide range of applicability for your outdoor power equipment needs.