Parts for Frigidaire AW300C0D: 04 - Tubs, Base Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Secures water or drain hoses to fittings, preventing leaks and loose connections. Replace when hoses slip or drip to restore a tight seal.

Lint filter screen for washers that traps debris and prevents drain clogs. Replace if damaged, torn, or clogged beyond cleaning. Confirm fit with model.

Washer tub seal prevents leaks between the drum and outer tub. Replace if you notice water pooling or dampness. Verify fit with your model number.

This part has been discontinued by the manufacturer and is no longer available.

Pressure tube connects washer tub to water level switch. Replace if cracked, kinked, or clogged to restore proper water level sensing in your laundry center.

Replacement fastening screw that secures panels, trim, or internal components in your washer. Needed when original is stripped, missing, or damaged.

This part has been discontinued by the manufacturer and is no longer available.

Suspension spring for washer tub support system. Replaces broken, stretched, or missing springs that no longer properly suspend the wash basket.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

The Spin Bearing Washer is an OEM part for Frigidaire washing machines. Situated inside the transmission housing, this thin metal washer acts as a subsurface support for the belt pulley bearing. The spin-bearing washer facilitates smooth, balanced rotation essential for agitated and spun wash cycles.

Causes of a bad spin-bearing washer include wear and fatigue from years of successive rotations, potentially allowing excessive movement between housing components.

Symptoms of a bad spin-bearing washer involve:

• Vibration or shaking noises coming from inside the washer cabinet
• Belt slippage wasting energy by inefficiently spinning loads
• Increased friction resulting in longer cycle times for spins
• Failure of belts or other components from unsupported bearing

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This replacement bolt secures internal components in your appliance. A stripped, rusted, or missing bolt can let parts loosen and vibrate; installing a new bolt restores a tight, stable connection for reliable operation.

• Provides a secure, threaded fastener for brackets, weights, or assemblies
• Helps maintain alignment and reduce movement during operation
• Typical issues: missing hardware, stripped threads, or visible corrosion
• Helps address rattling or excessive vibration caused by loose hardware

• Safety first: Disconnect power; for water- or gas-connected units, shut off supplies
• Support the component being secured before removing the old fastener
• Start threads by hand to avoid cross-threading; tighten evenly to manufacturer guidance—do not overtighten
• Reuse original washers/spacers and thread locker only if they were originally present

Secures the washer's inner basket to the drive hub, keeping the tub centered and stable during spin. Replace if cracked, corroded, or bolts are damaged.

Trunnion support for washer drum assembly. Replaces cracked, worn, or broken trunnion that causes misalignment. Restores stability to rotating drum.

The High Temperature Adhesive is an OEM part for Frigidaire appliances. This adhesive is specifically formulated to withstand high temperatures and is used in various repair applications within appliances such as ovens, ranges, and dryers.The 1-ounce tube contains adhesive formulated to withstand the extreme heat inside dryer drums and cabinets

Causes of a bad adhesive can include exposure to extremely high temperatures over extended periods, contamination by dirt or grease, or the natural aging and drying out of the adhesive.

Symptoms of a bad high temperature adhesive include:

• Components or parts becoming loose or detached
• The adhesive becoming brittle or cracked
• Inability to properly bond surfaces exposed to high heat
• Visible deterioration or peeling of the adhesive

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.