Parts for Frigidaire FFRA2822R2E0: Unit Parts

Front panel assembly for room air conditioners. Covers the unit's exterior face. Replace if cracked, damaged, faded, or missing to restore appearance.

Front panel for room air conditioners. Covers the front housing and provides finished appearance. Replace if cracked, broken, or discolored.

This refrigerator water filter removes common impurities from the ice and water supply so you get cleaner-tasting water and clearer ice. Designed to fit inline/replaceable filter housings used in many Frigidaire refrigerators. What it does:

• Reduces chlorine taste and odor for improved drinking water flavor
• Helps reduce sediment and particulates that can affect ice clarity
• Keeps water flowing properly when replaced as part of routine maintenance
• Addresses symptoms like cloudy ice, bad-tasting water, or reduced water quality

• One replacement refrigerator water filter cartridge

• Replace filter according to your refrigerator manufacturer's instructions; typically twist or push in to seat and lock
• Run several gallons of water through the dispenser after installation to flush the system and remove loose carbon fines
• If water flow is restricted after installation, check filter orientation and seating; do not force
• For safety, disconnect power to the appliance before accessing internal filter housings

Molded louver vent grille that directs airflow and covers the air opening on your room air conditioner. Replace if cracked, broken, or missing.

This refrigerator door handle provides a stable grip for opening and closing the door and restores the door's original appearance and function. Designed as a direct-fit replacement where this OEM-style handle is specified. What it does

• Replaces a damaged, cracked, or loose refrigerator door handle to restore safe, reliable opening and closing.
• Provides a secure grip and proper alignment for the door during normal use.
• Helps prevent further wear to the door edge and surrounding trim by restoring correct handle function.
• Compatible with factory handle mounting points when the OEM part number matches.

• One refrigerator door handle

• Installation typically requires removing the old handle screws or clips and securing the replacement in the same mounting locations.
• Use appropriate hand tools; avoid overtightening fasteners which can crack the handle or strip threads.
• Keep the door supported during removal/installation to avoid hinge or door damage.
• Turn off power to any nearby components (ice maker lights, etc.) before working.

Front panel link connector for room air conditioners. Secures and connects the front panel assembly. Replace if broken, cracked, or missing to restore panel fit.

Handheld remote control for air conditioners. Operates modes, temperature, fan speed, and timers from a distance. Replaces lost, broken, or non-working remotes.

Fix an air conditioner that won't shut off or has erratic operation. This electronic control board restores reliable cycle control and responsiveness.

The Thermistor is an OEM replacement part for Frigidaire room air conditioners. Located within the air conditioner unit, the thermistor accurately monitors and regulates the equipment's internal air temperature. Precisely calibrated at the factory, the thermistor allows the unit to continuously achieve and maintain the preset cooling level preferred by the user. 

Symptoms of a bad thermistor include:  

• Inconsistent or fluctuating room temperatures
• Difficulty reaching or maintaining desired temperatures  
• The control panel shows abnormal temperature readings

Causes can be age-related deterioration of sensing components, moisture exposure damaging circuitry, or loose wiring connections preventing exact temperature measurement over time. This OEM thermistor restores precise temperature control.

Replacing a faulty thermistor prevents improper compressor cycling which wastes energy. Compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This oven temperature sensor detects the internal temperature and sends readings to the range control so the oven can maintain accurate cooking temperatures. Replaces a failed or intermittent sensor to restore reliable temperature control. What it does:

• Senses oven cavity temperature and provides temperature data to the control board
• Helps the control maintain set bake/roast temperatures
• Common symptom: oven temperature is incorrect or fluctuates during cooking
• Common symptom: cook cycles take too long or oven does not reach set temperature
• Common symptom: oven displays a temperature sensor or sensor fault code

• One oven temperature sensor (1 each)

• Disconnect electrical power to the appliance before removing or installing the sensor
• Handle the sensor carefully to avoid damaging the probe or wiring and ensure proper connector seating
• Inspect wiring and connector for damage; replace if frayed or corroded

If your air conditioner won't turn on or runs but doesn't cool, the transformer may have failed. This part converts voltage to power the control board.

This replacement capacitor stores and releases electrical energy to support proper operation of the appliance's circuit. Replacing a weakened or failed capacitor restores reliable startup and smooth performance in the affected component.

• Stores electrical energy and delivers a brief boost during startup as designed by the circuit
• Helps stabilize operation, reducing humming, stalling, or overheating from a weak capacitor
• Common signs include motors that hum but won't start, intermittent operation, breaker trips
• Visual clues of failure: swollen case, leaking oil, or burnt odor

• Disconnect power and verify no voltage is present before servicing
• Properly discharge the old capacitor using safe, approved procedures
• Note wire positions or take a photo; transfer leads to the matching terminals securely
• Mount securely in the existing bracket/strap; keep terminals clear of contact and test operation

This replacement water supply tube routes water from the refrigerator's valve to the ice maker or dispenser, restoring proper water flow and preventing leaks when the original tube is cracked or blocked. What it does

• Carries water from the inlet/valve to the ice maker or dispenser assembly.
• Restores normal water flow when a damaged or clogged tube causes slow fill or no fill.
• Helps stop leaks and drips caused by cracks, splits or loose connections.
• Compatible with OEM connections and fittings used on affected Frigidaire refrigerators.

• One replacement water supply tube.

• Turn off the refrigerator and shut off the water supply before starting any work.
• Unplug the appliance to avoid electrical shock when accessing internal components.
• Replace only with the exact part number; secure all fittings to prevent leaks.
• After installation, restore water, check for leaks, and run a test fill to verify correct operation.

This scroll is the replaceable spiral element used inside a refrigeration compressor to compress refrigerant and restore proper cooling performance. It's the OEM-design component that engages with the mating scroll to form the compression chambers. What it does:

• Forms the moving or stationary spiral surface in a scroll-type compressor to compress refrigerant
• Restores internal compression when the factory scroll is damaged or worn
• Can help resolve symptoms such as loss of cooling, excessive compressor noise, or failed compression when diagnosis confirms scroll damage
• Works only as part of a compatible scroll compressor assembly; not a standalone drop-in pump solution

• Replacement requires compressor disassembly and reassembly
• Follow OEM torque, alignment, and sealant procedures; improper installation can cause compressor failure
• Observe all safety precautions for handling pressurized refrigerant and electrical components

Fix weak airflow or no air coming from your air conditioner with this blower wheel. Directly connects to the motor to circulate cool air. Easy DIY fix.

If your air conditioner isn't cooling evenly or has excessive frost buildup, this evaporator fan blade restores proper airflow across the cooling coils.

Front shroud panel for room air conditioners. Replaces cracked, broken, or missing exterior housing panels. Installs on the front of the unit.

Seal kit for air conditioners. Replace when you notice air leaks, reduced cooling efficiency, or moisture intrusion. Verify fit with your model number.

Mounting bracket for room air conditioners. Secures and supports the unit in the window frame. Replace if bent, rusted, cracked, or missing hardware.