Parts for Frigidaire FFRH2522R2E0: Unit Parts

Front panel for room air conditioners. Covers the front housing and provides finished appearance. Replace if cracked, broken, or discolored.

This is an air filter with a plastic frame designed to fit inside the refrigerator compartment. It helps remove odors and keep the air inside the refrigerator fresh by filtering out contaminants. Replace this filter if you notice persistent odors inside the refrigerator or if it has been in use beyond the recommended replacement interval.

Front panel for room air conditioner. Replaces cracked, broken, or damaged exterior panels. Restores clean appearance and proper cabinet coverage.

Molded louver vent grille that directs airflow and covers the air opening on your room air conditioner. Replace if cracked, broken, or missing.

Front louver grille for room air conditioners. Directs airflow and covers interior components. Replace if cracked, broken, or missing for proper appearance.

Fix intermittent power or dead controls with this single conductor wire. Restores electrical connections between components in your air conditioner unit.

This refrigerator door handle provides a stable grip for opening and closing the door and restores the door's original appearance and function. Designed as a direct-fit replacement where this OEM-style handle is specified. What it does

• Replaces a damaged, cracked, or loose refrigerator door handle to restore safe, reliable opening and closing.
• Provides a secure grip and proper alignment for the door during normal use.
• Helps prevent further wear to the door edge and surrounding trim by restoring correct handle function.
• Compatible with factory handle mounting points when the OEM part number matches.

• One refrigerator door handle

• Installation typically requires removing the old handle screws or clips and securing the replacement in the same mounting locations.
• Use appropriate hand tools; avoid overtightening fasteners which can crack the handle or strip threads.
• Keep the door supported during removal/installation to avoid hinge or door damage.
• Turn off power to any nearby components (ice maker lights, etc.) before working.

Front panel link connector for room air conditioners. Secures and connects the front panel assembly. Replace if broken, cracked, or missing to restore panel fit.

Fix an air conditioner that won't cool, turn on, or respond to controls. This main control board manages all functions. Moderate DIY repair.

The Thermistor is an OEM replacement part for Frigidaire room air conditioners. Located within the air conditioner unit, the thermistor accurately monitors and regulates the equipment's internal air temperature. Precisely calibrated at the factory, the thermistor allows the unit to continuously achieve and maintain the preset cooling level preferred by the user. 

Symptoms of a bad thermistor include:  

• Inconsistent or fluctuating room temperatures
• Difficulty reaching or maintaining desired temperatures  
• The control panel shows abnormal temperature readings

Causes can be age-related deterioration of sensing components, moisture exposure damaging circuitry, or loose wiring connections preventing exact temperature measurement over time. This OEM thermistor restores precise temperature control.

Replacing a faulty thermistor prevents improper compressor cycling which wastes energy. Compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This is a thermistor-style temperature sensor that monitors the evaporator coil temperature in a room air conditioner. It sends temperature readings to the control board so the unit can regulate cooling cycles and prevent the evaporator from freezing over. Replace this sensor if the air conditioner runs continuously without cycling off, fails to cool properly, displays an error code, or if the evaporator coil ices up excessively.

If your air conditioner won't turn on or runs but doesn't cool, the transformer may have failed. This part converts voltage to power the control board.

This replacement capacitor stores and releases electrical energy to support proper operation of the appliance's circuit. Replacing a weakened or failed capacitor restores reliable startup and smooth performance in the affected component.

• Stores electrical energy and delivers a brief boost during startup as designed by the circuit
• Helps stabilize operation, reducing humming, stalling, or overheating from a weak capacitor
• Common signs include motors that hum but won't start, intermittent operation, breaker trips
• Visual clues of failure: swollen case, leaking oil, or burnt odor

• Disconnect power and verify no voltage is present before servicing
• Properly discharge the old capacitor using safe, approved procedures
• Note wire positions or take a photo; transfer leads to the matching terminals securely
• Mount securely in the existing bracket/strap; keep terminals clear of contact and test operation

This tube guides defrost and condensation water from the evaporator area to the refrigerator drain pan, helping prevent water pooling and leaks inside the cabinet. It's a simple replacement that restores proper drainage. What it does:

• Channels meltwater from the evaporator to the drain pan to prevent interior puddling
• Helps stop water leaks under or inside the refrigerator when intact
• Reduces chance of odors from standing water by keeping water moving to the drain pan
• Symptoms of a bad tube: visible leaks, water pooling inside the fresh-food section, or water under the appliance

• One drain tube

• Disconnect power to the appliance before beginning any service
• May require removing interior panels or the evaporator cover to access and route the tube
• Inspect and reuse or replace any retaining clips, grommets, or clamps as needed
• Handle the tube gently to avoid kinks; ensure proper seating in the drain trough and pan for correct flow

This replacement water supply tube routes water from the refrigerator's valve to the ice maker or dispenser, restoring proper water flow and preventing leaks when the original tube is cracked or blocked. What it does

• Carries water from the inlet/valve to the ice maker or dispenser assembly.
• Restores normal water flow when a damaged or clogged tube causes slow fill or no fill.
• Helps stop leaks and drips caused by cracks, splits or loose connections.
• Compatible with OEM connections and fittings used on affected Frigidaire refrigerators.

• One replacement water supply tube.

• Turn off the refrigerator and shut off the water supply before starting any work.
• Unplug the appliance to avoid electrical shock when accessing internal components.
• Replace only with the exact part number; secure all fittings to prevent leaks.
• After installation, restore water, check for leaks, and run a test fill to verify correct operation.

Air conditioner not cooling properly? A faulty condenser coil prevents heat removal, causing poor cooling and compressor strain. Restore efficient operation.

A replacement dryer heater assembly that supplies the hot air needed to dry clothes. Restores normal drying performance when the original heater element fails or stops producing heat. What it does

• Heats air passing through the dryer drum so laundry dries efficiently.
• Commonly replaces a failed or open heating element causing no heat or long drying times.
• Works with the dryer's blower and thermostats to maintain operating temperature.
• Helps resolve symptoms like clothes remaining damp or extended cycle times.

• One heater assembly as shown.

• Disconnect power to the dryer before servicing to avoid shock or injury.
• Access typically requires removing the dryer rear or front panel; follow the model's service manual.
• Inspect related parts when replacing the heater.

This is the fan motor that drives the blower or condenser fan in a room air conditioner, circulating air across the evaporator and condenser coils. It is essential for proper cooling and air distribution. Replace this motor if the unit is not blowing air, runs but does not cool effectively, or if you hear grinding or humming noises coming from the fan area.

If your air conditioner isn't cooling evenly or has excessive frost buildup, this evaporator fan blade restores proper airflow across the cooling coils.

Front shroud panel for room air conditioners. Replaces cracked, broken, or missing exterior housing panels. Installs on the front of the unit.

Seal kit for air conditioners. Replace when you notice air leaks, reduced cooling efficiency, or moisture intrusion. Verify fit with your model number.

Mounting bracket for room air conditioners. Secures and supports the unit in the window frame. Replace if bent, rusted, cracked, or missing hardware.