Parts for Ge GTE17GBCBRWW: 03 - Unit Parts

Refrigerator condenser felt tape seals and insulates the condenser area. Replace when worn, torn, or losing adhesion to maintain efficiency. Verify fit with your model number before ordering.

Sheet metal screw secures refrigerator panels, trim, and brackets. Replace missing, stripped, or corroded screws to restore proper fit and assembly.

Fix electrical connection issues in your refrigerator with this terminal block socket assembly. Connects power to components. Moderate DIY repair.

Replacement plug cover and gasket assembly for refrigerator electrical access areas. Restores secure fit when original is cracked, broken, or missing.

Vinyl sleeve that fits over rods, tubes, or wires in your refrigerator. Replace if cracked, torn, or missing to protect contact points and reduce wear.

Fix a refrigerator that freezes food or runs too cold with this temperature control thermostat. Common DIY repair with video guide, typically done in 10-15 minutes.

The Bulb Light is an OEM part for GE refrigerators. It is designed to illuminate the interior of the refrigerator and freezer compartments, making it easier to see and access food items. This light bulb fits securely into the designated socket and provides bright, reliable lighting to enhance visibility.

You should replace the bulb light if it burns out or becomes damaged. Causes of a bad bulb light can include regular wear and tear, electrical issues, or physical damage from impacts or vibrations. A faulty bulb can leave the refrigerator compartments dim or completely dark, making it difficult to find items.

Symptoms of a bad bulb light include:

• The light not turning on when the refrigerator door is opened
• Flickering or intermittent lighting
• A visibly burned-out or broken bulb

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Lid Bumper is an OEM part for GE refrigerators. It is designed to provide cushioning and protection for the refrigerator lid, preventing damage and ensuring smooth, quiet closing. 

Causes of a bad Lid Bumper can include deterioration over time due to frequent use, exposure to temperature variations, or damage from accidental impacts. A worn or damaged bumper may no longer provide adequate cushioning, leading to potential damage to the lid or the refrigerator itself.

Symptoms of a bad Lid Bumper include:

• The refrigerator lid closing too hard
• Unusual noises when closing the lid
• Visible wear or cracks on the bumper

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This screw is a genuine General Electric part, sold individually. This screw can be used as a replacement part for a refrigerator. A screw can suffer damage in the lifespan of a refrigerator. It can also be easily lost or misplaced. Screws are small parts and are usually installed in multiples to ensure components are reliably attached, so one screw loosening or going missing might not necessarily affect the operability of the refrigerator. However, if the components loosen or the screw suffers damage that strips the part, such as punctures or erosion to the metal material from general wear and tear or from a direct impact, the screw should be removed and replaced with this genuine OEM replacement part. This is an OEM part sourced directly from the manufacturer, and it is sold individually. This screw is compatible with the following appliance brands: General Electric, Hotpoint, RCA, and Americana.

Replacement mounting screw for refrigerator interior components. Needed when original hardware is stripped, missing, or damaged during repairs or maintenance.

SCR solid-state switching module that controls power flow in refrigerator circuits. Replace when module is damaged, burned out, or failing to switch properly.

Interior light not working when door opens? This light switch controls refrigerator illumination. DIY-friendly install takes 30-45 minutes with video.

Rubber grommet cushions and stabilizes the evaporator fan motor in your refrigerator. Replace if cracked, worn, or missing to reduce vibrations and noise.

Freezer icing up or fridge too warm? The defrost thermostat monitors evaporator temperature to prevent frost buildup. DIY repair in under an hour.

This holder element assembly secures the appliance's heating element in the correct position so the element stays stable for consistent operation and safe performance. It's a direct-fit replacement for worn or damaged holders. What it does:

• Secures and supports the heating element inside the appliance to maintain proper alignment
• Prevents element sagging or contact with other components that can cause noise or arcing
• Helps reduce vibration and movement that can lead to intermittent heating
• Common symptom: visible holder damage, loose or shifted element, unusual noise during operation

• Disconnect power (unplug or switch off breaker) before starting any repair
• Allow appliance and element to fully cool before handling
• Handle the element and holder carefully to avoid bending or damaging the element

Supplies electrical power from wall outlet to refrigerator. Replace this cord if cut, frayed, overheated, or damaged to restore safe electrical connection.

Strain relief retainer secures electrical cables where they enter the refrigerator. Replace if cracked, broken, or missing to protect wiring connections.

Refrigerator running hot or making loud noises? A worn condenser fan blade prevents proper airflow across coils. DIY repair in 30 minutes or less.

Secures and seals water line connections in your refrigerator's dispensing system. Replace if leaking or loose to prevent water damage. Confirm fit.

Fix a refrigerator that won't cool or runs constantly with this compressor kit. Essential for restoring proper cooling in refrigerators and freezers.

Fix a refrigerator that won't cool or run with this compressor start capacitor. Helps the compressor motor start reliably. Moderate DIY repair.

The R134 Drier is an OEM part for GE refrigerators. This component plays a critical role in the refrigeration system by removing moisture and contaminants from the refrigerant, ensuring efficient cooling and preventing damage to other parts of the system. It helps maintain the purity and effectiveness of the refrigerant as it cycles through the system.

You should replace the R134 drier if it becomes clogged or damaged. Common causes of a bad drier include wear and tear over time, exposure to moisture, or contamination from other failing components in the refrigeration system.

Symptoms of a bad R134 drier include:

• Reduced cooling efficiency
• Frost buildup on the evaporator coils
• Unusual noises from the refrigeration system
• Increased energy consumption
• Refrigerator not maintaining the set temperature

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Replacement shelf support stud for refrigerator shelves. Installs to hold shelves in place. Needed when original stud is broken, cracked, or missing.

Replacement mounting screw for securing panels, trim, and internal components in appliances. Needed when original screws are stripped, lost, or damaged.

Secures the condenser fan motor in position. Replace this bracket if cracked, bent, or causing excessive vibration to restore stable mounting.

Secures brackets, panels, and internal components in your refrigerator. Replace missing or damaged screws to eliminate rattles and keep parts aligned.

Secures the condenser unit in your refrigerator. Replace if loose, broken, or causing vibration noise. Verify fit with your model number before ordering.