Parts for Ge PFSF6PKWBBB: 09 - Unit Parts

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

This water line holder secures a refrigerator or ice maker supply tube to the cabinet or internal frame to keep the line routed and stable. Replacing a worn or missing holder helps prevent rubbing, kinks, and stress on the water line. What it does:

• Holds the water supply line in place to reduce movement and wear
• Helps prevent kinks that can restrict water flow to icemakers and dispensers
• Reduces vibration and potential chafing against sharp edges
• Addresses symptoms like a loose or sagging water line, intermittent flow, or audible line movement

• One water line holder clip

• Disconnect power and shut off the water supply before servicing
• Inspect the water line for damage; replace the line if cracked or leaking
• Mounting may require a screw, push-fit, or slot engagement depending on model—retain existing fasteners or your model's instructions

Refrigerator not cooling or buttons not responding? This main control board coordinates cooling cycles, defrost, and fan operation to restore function.

Fix unresponsive temperature controls and blank LED displays on your refrigerator. This control board restores touch pad functionality and display.

Protective cover that shields the main control board in your refrigerator. Replace if cracked, broken, or missing to protect electronics from damage.

This molded rubber condenser grommet cushions and positions the condenser assembly to reduce vibration and wear. It restores proper mounting alignment so the condenser sits securely and operates quietly. What it does:

• Cushions condenser against the cabinet frame to dampen vibration and rattling
• Helps hold the condenser in proper position for correct airflow and clearance
• Prevents metal-to-metal contact that can cause noise or part wear
• Commonly used when the condenser rattles, vibrates, or sits loose after impact or age

• One condenser grommet

• Disconnect power to the appliance before servicing to avoid electrical shock
• Access the condenser from the back or lower rear, remove any service panels as needed
• Remove the old grommet and press the new grommet into place on the condenser mounting post or bracket

Fix a warm refrigerator or noisy cooling system with this condenser fan motor assembly. Restores airflow across condenser coils for proper cooling.

Rubber grommet that cushions and stabilizes the compressor in your refrigerator. Replace if cracked, deteriorated, or missing to restore support.

Fix a refrigerator that won't cool or runs constantly with this compressor. Essential sealed system component that circulates refrigerant through the system.

Replacement wire harness assembly that connects electrical power to the refrigerator compressor. Needed when wiring is frayed, damaged, or corroded.

Refrigerator clicking but not cooling? A failed compressor overload protector prevents the compressor from starting. This part restores normal operation.

Refrigerator dryer clip secures the moisture filter system in place. Replace if broken, loose, or causing rattling noises. Verify fit with your model number.

Fix a refrigerator that's not cooling properly with this compressor suction line. Connects the evaporator to the compressor in the sealed system.

Secure refrigerator suction line clamp holds refrigerant tubing in place. Replace if damaged, cracked, or loose to prevent vibration noise and maintain proper cooling. Verify fit by model number.

Drain line assembly routes defrost water from the evaporator to the drain pan. Replace if cracked, clogged, or leaking to restore proper drainage.

Ground wire harness for refrigerators. Connects electrical components to ensure proper grounding. Replace if damaged, frayed, or disconnected.

Replacement EMI noise filter for your refrigerator. Suppresses electromagnetic interference from the control board. Order a new filter if yours is cracked or damaged.

Fix a refrigerator with no water dispenser flow, slow water, or leaking dispenser. This dual water inlet valve controls water to the dispenser and icemaker.

A replacement compressor mounting bolt that secures the refrigerator compressor to the chassis to help keep the compressor stable and reduce vibration. Direct-fit hardware to restore proper compressor attachment and quiet operation. What it does:

• Fastens the compressor to the refrigerator frame or mounting bracket for secure operation
• Keeps the compressor aligned to prevent movement and reduce vibration-related noise
• Helps maintain a stable seal for connected refrigerant lines by preventing compressor shifting
• Appropriate when original bolt is stripped, corroded, or missing

• Disconnect power to the appliance before starting any repair
• Support the compressor or mounting bracket while removing/installing the bolt to prevent strain on lines
• Use correct socket/wrench size and replace with identical hardware; do not overtighten
• Address those issues before reuse

This rubber grommet seals the suction/water pipe where it passes through the appliance cabinet to reduce leaks and dampen vibration. It restores a tight, durable seal to help prevent water intrusion and rattling. What it does:

• Cushions and seals the suction/water pipe where it passes through sheet metal or plastic.
• Reduces vibration and pipe movement that can cause noise or wear.
• Helps prevent water leaks or moisture entry at the cabinet penetration.
• Maintains a proper fit for tubing routing and component alignment.

• One rubber suction pipe grommet.

• Disconnect power and shut off water supply before servicing.
• Remove access panels as needed to reach the pipe penetration; press grommet into opening and route pipe through center.
• Replace any brittle, torn, or deformed grommets; do not force a damaged grommet into place.