Parts for Ge PFSS9SKYBSS: 09 - Unit Parts

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

This water line holder secures a refrigerator or ice maker supply tube to the cabinet or internal frame to keep the line routed and stable. Replacing a worn or missing holder helps prevent rubbing, kinks, and stress on the water line. What it does:

• Holds the water supply line in place to reduce movement and wear
• Helps prevent kinks that can restrict water flow to icemakers and dispensers
• Reduces vibration and potential chafing against sharp edges
• Addresses symptoms like a loose or sagging water line, intermittent flow, or audible line movement

• One water line holder clip

• Disconnect power and shut off the water supply before servicing
• Inspect the water line for damage; replace the line if cracked or leaking
• Mounting may require a screw, push-fit, or slot engagement depending on model—retain existing fasteners or your model's instructions

Fix a refrigerator that won't cool, has display errors, or stops running with a new main control board. Moderate difficulty repair in 1-2 hours.

Fix a refrigerator that won't cool, runs constantly, or has erratic temperature with this main control board. Manages compressor, defrost cycles, and cooling.

This inverter board controls the variable speed operation of your refrigerator's compressor, optimizing cooling efficiency and reducing energy consumption. It adjusts compressor speed based on cooling demands to maintain consistent temperatures. Replace it when the refrigerator runs constantly, temperatures fluctuate, or the compressor won't start.

This molded rubber condenser grommet cushions and positions the condenser assembly to reduce vibration and wear. It restores proper mounting alignment so the condenser sits securely and operates quietly. What it does:

• Cushions condenser against the cabinet frame to dampen vibration and rattling
• Helps hold the condenser in proper position for correct airflow and clearance
• Prevents metal-to-metal contact that can cause noise or part wear
• Commonly used when the condenser rattles, vibrates, or sits loose after impact or age

• One condenser grommet

• Disconnect power to the appliance before servicing to avoid electrical shock
• Access the condenser from the back or lower rear, remove any service panels as needed
• Remove the old grommet and press the new grommet into place on the condenser mounting post or bracket

Rubber grommet that cushions and stabilizes the compressor in your refrigerator. Replace if cracked, deteriorated, or missing to restore support.

Ground wire harness for refrigerators. Connects electrical components to ensure proper grounding. Replace if damaged, frayed, or disconnected.

Replacement power cord for your refrigerator. Connects unit to wall outlet. Needed when original cord is damaged, frayed, or missing. Direct fit.

This fitting connects the water supply line to your refrigerator's water inlet valve, typically located at the back of the unit. Replace if you notice water leaks around the connection or reduced water flow to the dispenser or ice maker.

A replacement compressor mounting bolt that secures the refrigerator compressor to the chassis to help keep the compressor stable and reduce vibration. Direct-fit hardware to restore proper compressor attachment and quiet operation. What it does:

• Fastens the compressor to the refrigerator frame or mounting bracket for secure operation
• Keeps the compressor aligned to prevent movement and reduce vibration-related noise
• Helps maintain a stable seal for connected refrigerant lines by preventing compressor shifting
• Appropriate when original bolt is stripped, corroded, or missing

• Disconnect power to the appliance before starting any repair
• Support the compressor or mounting bracket while removing/installing the bolt to prevent strain on lines
• Use correct socket/wrench size and replace with identical hardware; do not overtighten
• Address those issues before reuse

The Relay Protector is an OEM part for GE refrigerators. The relay protector monitors voltage input for irregular surges or drops that could harm electronic control boards over time. Upon detection, it immediately redirects excess voltage away from relays to safeguard sensitive circuits.

Causes can be damage from sustained power fluctuations over years of use. Failure allows increased risk of voltage abnormalities affecting parts.

Symptoms of a faulty relay protector include:

• Refrigerator cycles unexpectedly turning off
• Inoperative zones within, like water/ice dispensers
• Frequent component burnouts requiring replacements
• Buzzing noises from the electrical outlet area

This OEM GE  part is also compatible with Hotpoint, RCA, and some Kenmore models.

Protective cover that fits over the compressor relay. Shields relay from dirt, moisture, and contact. Replace if cracked, broken, or missing.