Parts for Ge TFX25CPCEAA: 06 - Unit Parts

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

Secures water and drain tubing to prevent leaks, noise, and vibration. Replace if loose, cracked, or missing. Confirm fit with your model number.

Rubber grommet seals the ice maker fill tube where it enters the refrigerator cabinet. Replace if cracked, brittle, leaking, or missing to restore seal.

Plastic plug button insert for refrigerator shelves and interior panels. Replaces missing, cracked, or broken plug inserts that leave exposed holes.

Secures refrigerator wiring to prevent chafing and vibration noise. Replace when damaged or missing to keep harnesses organized. Confirm fit by model.

Supplies electrical power from wall outlet to refrigerator. Replace this cord if cut, frayed, overheated, or damaged to restore safe electrical connection.

Sealer plug for refrigerators. Seals unused holes or openings in cabinet panels. Replace if cracked, broken, or missing to maintain proper appearance.

This evaporator fan motor dust cap is an authentic OEM replacement part found on refrigerator and freezer fan motors. This dust cap prevents the fan motor bearing and housing from being damaged by dirt and debris. If the dust cap is cracked or broken, the fan may make loud squealing noises. If the dust cap is not removed and replaced, the fan could stop working and ultimately cause the refrigerator's temperature to be affected. To start, disconnect the power and water to the refrigerator. Remove food from the freezer so that the back panel of the freezer can be accessed to reach the fan. Remove the ice maker and set it outside the freezer. Disconnect the fan and take it out of the freezer to expose the fan's shaft and the dust cover. Pry the dust cover off and install the new one. Replace the fan and cover. Reconnect the wires and reinstall the icemaker. Put the food back in the freezer. Reconnect the power and water.The evaporator fan motor dust cap is a white plastic part that is sold individually. This dust cover is made for use in refrigerators manufactured by General Electric, Hotpoint, and Kenmore.

This part has been discontinued by the manufacturer and is no longer available.

Refrigerator won't cool and compressor just clicks or hums? The start relay helps the compressor motor start. Moderate DIY repair, clean coils first.

This is a small clip used to secure the condenser tubing or coil in place on the back or underside of a refrigerator. It keeps the condenser components properly positioned for efficient heat dissipation. Replace this clip if it is broken or missing, which can allow condenser tubing to shift, vibrate, or contact other parts and cause rattling noises.

The R134 Drier is an OEM part for GE refrigerators. This component plays a critical role in the refrigeration system by removing moisture and contaminants from the refrigerant, ensuring efficient cooling and preventing damage to other parts of the system. It helps maintain the purity and effectiveness of the refrigerant as it cycles through the system.

You should replace the R134 drier if it becomes clogged or damaged. Common causes of a bad drier include wear and tear over time, exposure to moisture, or contamination from other failing components in the refrigeration system.

Symptoms of a bad R134 drier include:

• Reduced cooling efficiency
• Frost buildup on the evaporator coils
• Unusual noises from the refrigeration system
• Increased energy consumption
• Refrigerator not maintaining the set temperature

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Stamped steel plate that secures the compressor to the refrigerator cabinet. Replace if cracked, bent, or rusted to restore stability and reduce vibration.

Secures the condenser unit in your refrigerator. Replace if loose, broken, or causing vibration noise. Verify fit with your model number before ordering.

Plastic cover that conceals and protects water supply tubing behind the lower kickplate. Replace if cracked, broken, or missing for a finished look.

Secures water tubing to fittings in refrigerators and dishwashers. Replace if leaking, tubing slips off, or clamp is cracked. Confirm fit with model number.

Mounting bracket that secures the water valve in your refrigerator. Replace if the bracket is cracked, bent, broken, or missing to properly support the valve.

Fix leaking water or a non-working ice maker with this refrigerator water inlet valve. Moderate DIY repair in 30-45 minutes with basic tools.

Wire harness assembly that routes electrical connections between refrigerator components. Replace if wires are damaged, frayed, broken, or corroded.

Fix no water dispensing or leaking behind your refrigerator. This water inlet valve controls flow to the ice maker and dispenser. DIY repair in under an hour.

Ice maker not filling or water dispenser leaking? This water inlet valve controls flow to your ice maker and dispenser. Most DIYers complete in 15-30 minutes.

Plastic water line that connects the water inlet valve to the ice maker. Replace if cracked, leaking, or damaged. Includes installation video.

Secures water tube to cabinet, preventing kinks and flow issues. Replace if tube is loose, vibrating, or causing noise. Confirm fit with your model number.