Parts for Kitchenaid KSCS25FVMK03: 11 - Unit Parts

Reduces contaminants for cleaner, better-tasting water and ice. Replace every 6 months or when indicator light activates. Verify fit by model number.

8-32 x 1/4 inch mounting screw for securing panels and components. Replace missing, stripped, or damaged screws during repairs or reassembly.

Fix clicking noise, poor cooling, or overheating compressor by replacing a cracked or warped condenser fan blade. Restores airflow across the coil.

Is your refrigerator not cooling properly or running constantly? A failing condenser may be the cause. This part helps release heat from the system.

Adhesive foam insulation pad that reduces vibration and noise in refrigerators. Replaces worn, missing, or deteriorated sound dampening pads.

Replace stripped, missing, or corroded mounting screws in your refrigerator or freezer. Secures panels, brackets, and components for proper fit.

Guide sleeve for washer drum or agitator assembly. Replaces worn, cracked, or missing sleeves that cause misalignment or rattling during operation.

Seals openings where hoses or wires pass through cabinet walls. Replace if cracked, torn, or missing to prevent chafing and vibration noise. Verify fit.

Mounting screw for refrigerator assembly. Secures internal components and panels. Replace if stripped, rusted, missing, or damaged during repairs.

Protects the terminal block on your refrigerator compressor by shielding electrical connections. Replace if cracked, broken, or missing for safety.

Secures power cord to your ice maker or refrigerator. Replace if cracked, broken, or missing to prevent cord damage and ensure safe operation. Verify fit.

Replacement fastener screw for appliances. Secures panels, trim, clips, and components. Needed when original screws are stripped, missing, or damaged.

Freezer not cooling or excessive frost buildup? The evaporator assembly circulates refrigerant to remove heat. Moderately difficult repair for DIYers.

Fix frost buildup in your refrigerator with this defrost heater mounting clip. Secures heater to evaporator for consistent defrosting performance.

Refrigerator not cooling but freezer works? A failed condenser fan motor prevents heat from escaping. DIY repair takes 10-20 minutes with basic tools.

Refrigerator not cooling properly? A clogged filter drier prevents proper refrigerant flow. Requires professional installation due to sealed system.

If your refrigerator isn't cooling or runs constantly, the compressor may have failed. This critical component circulates refrigerant through the system.

This main wire harness provides the factory-style wiring that links the control and major components, restoring reliable electrical connections and stable operation. Designed as a direct replacement to help fix wiring faults and intermittent component issues. What it does:

• Routes power and signal connections between the control board and appliance components.
• Replaces damaged, chafed or corroded wiring that can cause intermittent operation or component failures.
• Helps resolve symptoms such as components not responding, intermittent cycles, or electrical arcing at connectors.
• Maintains correct connector fit and wiring order to preserve original function and safety.

• Disconnect all power (unplug or switch off breaker) before starting any repair.
• Compare the new harness to the old harness and follow the appliance wiring diagram for routing and connector locations.
• Handle connectors carefully; press release tabs fully to avoid breaking locking clips.
• If wiring shows heat damage or connector melting, inspect adjacent components and replace damaged parts rather than repairing with tape or splices.

Refrigerator won't cool or compressor won't run? This inverter box assembly controls the compressor and fan motor to restore proper cooling function.

Rubber grommet kit that mounts and cushions the compressor. Replace worn, cracked, or damaged grommets to restore proper support and isolation.

Refrigerator not cooling or making unusual noises? This compressor system tube connects critical sealed system components for proper refrigerant flow.

Rubber grommet kit that mounts and cushions the compressor. Replace worn, cracked, or damaged grommets to restore proper support and isolation.

Replace your refrigerator's internal wire harness if damaged, frayed, or corroded. Connects electrical components inside the appliance compartment.

Connects water line sections in your refrigerator. Replace if cracked, leaking, or damaged to restore secure connections to ice maker and dispenser.

Size: 1/2 inch.

Size: 5/8 inch.

Fix refrigerant leaks or low cooling with this 3/4 inch service valve. Essential for AC system pressure testing and refrigerant recharge procedures.

Fix refrigerant leaks or low cooling with this 3/16 inch service valve. Essential for AC recharging and system maintenance on multiple models.

Refrigerator not cooling properly? A faulty 1/4 inch service valve can prevent proper refrigerant flow. This valve connects refrigerant lines in your system.

Service valve for refrigerators, freezers, and ice makers. Used for refrigerant system service and maintenance. 5/16 inch fitting size for technicians.

Fix refrigerant leaks or cooling issues with this 3/8 inch service valve. Essential for refrigeration system repairs and maintenance on multiple models.