Parts for Lg LDE4415BD: Upper Cavity Parts

This customized screw is the exact fastener specified by the manufacturer to secure components in select LG appliances. Replacing a missing or stripped screw restores a tight, rattle-free fit and helps maintain proper alignment over time.

• Secures panels, brackets, and internal assemblies at original mounting points
• Helps reduce vibration and rattling noises from loose hardware
• Replaces missing, rusted, or stripped screws
• Supports stable operation by keeping parts firmly in place

• Disconnect power; shut off water or gas before service
• Match the screw to the exact location using your model's parts diagram
• Start threads by hand; tighten snugly without overtightening to avoid stripping
• Use the correct driver bit for the head style to prevent damage

This reflector directs heat and light inside the oven cavity so food browns evenly and the cavity stays properly illuminated. It replaces a damaged or warped reflector to restore cooking consistency and interior lighting function. What it does

• Redirects oven heat and light toward the cooking cavity for even browning and consistent results
• Protects internal components by covering the cavity area and helping maintain proper heat distribution
• Can reduce hot spots caused by a warped or damaged reflector
• Commonly replaced when the reflector is dented, corroded, cracked, or missing

• Disconnect power to the appliance before accessing the oven cavity to avoid shock or injury
• Remove any racks and cooling items first; handle the reflector carefully to avoid sharp edges
• Use basic hand tools; secure fasteners per manufacturer guidance and do not overtighten

The Carbon Heater is an OEM part for LG electric ranges. As an internal heating element, the carbon heater element generates consistent, powerful heat for the range's oven. It radiates even heat throughout the oven cavity to cook and bake foods as intended.

Symptoms of a faulty carbon heater include: 

• Inconsistent or improper oven temperatures
• Fluctuating heat levels between baking cycles  
• Discoloration, cracking or damage to the heating coil
• Occasional tripping of circuit breakers

Causes can be regular wear over many bake cycles, mineral buildup inhibiting heat transfer or physical damage to fragile coil filaments. 

This part is also compatible with select Sears/Kenmore electric ranges.

This heater cover protects the dryer heater assembly and helps direct airflow for efficient operation. Replacing a damaged cover restores proper heater protection and reduces the risk of airflow restriction or overheating. What it does:

• Shields the heating element and internal wiring from debris and lint buildup
• Helps channel hot air through the drum and vent path for consistent drying
• Prevents direct contact with the heater, improving safety
• Addresses symptoms like excessive lint accumulation, rattling near the heater area, or minor airflow issues

• One heater cover

• Disconnect power to the appliance before starting any repairs
• Typical install requires removing the dryer cabinet or access panel; follow OEM instructions
• Inspect surrounding components (heater, element housing, mounting clips) and replace any damaged fasteners

This heater bracket secures the dryer heater assembly so the heater stays properly positioned during operation, helping prevent noise and alignment issues. It's a direct-fit replacement when the original bracket is broken or worn. What it does:

• Holds the heater element or assembly in place to maintain correct alignment
• Prevents vibration and rattling that can occur with a loose heater
• Helps maintain safe clearance between the heater and surrounding components
• Can be replaced when cracked, bent, or when heater movement is observed

• One heater mounting bracket

• Disconnect power (unplug electric or switch off breaker) before beginning service
• Access typically requires removing the dryer top or rear panel; follow your model's service manual
• Inspect nearby insulation and wiring for heat damage while replacing the bracket

This heater mounting bracket secures the appliance's heating element in the correct position for safe, reliable operation. Replacing a bent or missing bracket helps prevent vibration, contact damage, and uneven heating from a sagging element.

• Holds the heater element firmly and maintains proper alignment/clearance
• Helps restore stable heating when the element has shifted or loosened
• Replaces brackets that are bent, cracked, corroded, or missing
• Can reduce rattling or vibration noises from the heater area

• Disconnect electrical power before servicing; allow hot components to cool
• Access the heater area and document original routing and hardware
• Transfer the heater to the new bracket; reuse original screws/clips if serviceable
• Verify proper clearances from wiring and panels before restoring power

This small, board-mounted tactile push-button switch is used on the control panel. It registers a momentary press so the control board can accept your selection. Replacing a worn switch restores reliable button response and consistent operation.

• Mounts to the user interface board and provides momentary contact when a button is pressed
• Sends a low-voltage signal to the control, enabling cycle or option selection
• Typical failure symptoms: unresponsive or intermittent buttons, needing extra force to register, stuck/always-on input, or unintended beeps/changes
• Helps restore consistent user-interface input when an individual button switch has failed

• Disconnect power to the appliance before servicing; shut off gas/water if applicable
• Access the control panel to reach the user interface board
• This is a board-level repair; note switch orientation. Replacement may require desoldering/soldering per OEM procedure
• Use ESD precautions and avoid overheating PCB pads; test button function before reassembly

The Thermistor is an OEM replacement part for LG gas ranges. It serves as a highly sensitive temperature sensor mounted inside the oven cavity. 

Symptoms of a bad thermistor include:  

• Inability to select certain cooking modes like bake or convection that involve temperature control
• Fluctuating or inaccurate temperature readouts on oven displays
• Irregular cooking outcomes like hot/cold spots inside the oven
• Repeated error codes regarding temperature sensing issues

Causes can be attributed to prolonged exposures to heat and intermittent combustion byproducts inside the oven. Over a decade of use, these conditions may degrade the thermal and electrical properties of sensor components. 

This genuine LG replacement thermistor installs effortlessly. Installing a new thermistor restores temperature monitoring required for reliable gas oven performance. 

The Bracket Assembly is an OEM component specifically designed for LG electric ranges utilizing rear-mount control panels. This integral assembly securely attaches the command console within the unit cabinetry.

Causes of a bad bracket can include loosening or stripped screws no longer maintaining a tight interface, impacts warping the steel base compromising flush mounting, or corrosion where dissimilar metals contact deteriorating securing points.

Symptoms of a bad bracket assembly include: 

• Loose panel unable to be properly reinstalled  
• Scratches or abrasions from rattling components
• Drooping controls suffering misaligned activation zones  
• Detached splash guard failing to fully protect surfaces

Replace yours today with this genuine OEM LG assembly to restore a robust interface. Backed mounting flanges deliver long-term stability and compatibility when replacing Samsung, Frigidaire, or GE electric ranges requiring rear console mounting as well. 

The Magnetron Thermostat is an OEM part for LG microwaves and built-in ranges. Its primary function is to monitor the temperature and ensure that it remains within a safe operating range. If the temperature exceeds the preset limit, the thermostat will interrupt the power supply to the magnetron, preventing overheating and potential damage.

Causes of a faulty magnetron thermostat can include electrical malfunctions, component failures, or physical damage. These factors can result in issues such as erratic heating, microwave not heating properly, or the appliance shutting off unexpectedly.

Symptoms of a bad magnetron thermostat may include:

• Microwave not heating food evenly or at all
• Inconsistent or weak heating performance
• Microwave shutting off or displaying error codes related to temperature issues

This OEM LG part can also be used on Kenmore/Sears appliances. 

This incandescent oven lamp provides interior illumination so you can safely check food without opening the door. Direct replacement for a burned or dim oven/range light to restore cooking visibility. What it does

• Replaces a burned-out or flickering oven interior light bulb
• Restores clear visibility of the oven cavity for monitoring cooking progress
• Helps avoid opening the oven door unnecessarily, preserving oven temperature
• Fits the original lamp socket and installs in the oven light housing

• Disconnect power to the appliance before replacing the lamp to prevent electric shock
• Allow the oven and old bulb to cool completely before handling
• Use a cloth or gloves when installing the new lamp to avoid transferring oils from skin

This AC synchronous motor assembly drives the appliance's rotating components to restore proper operation and consistent performance. It replaces a failed motor to stop stalling, humming or lack of rotation in affected units. What it does:

• Converts electrical input into smooth, synchronous rotational motion for the appliance's driven component
• Stops symptoms like no spin, intermittent rotation, or a motor that hums without turning
• Restores stable, timed movement where a synchronous motor is required
• Interfaces with the appliance's original mounting and wiring harness for direct replacement

• Disconnect power before beginning any repair to avoid electrical shock
• Verify wiring harness orientation and connector seating before applying power
• Inspect mounting points and shaft coupling for wear and secure per OEM guidelines