Parts for Ge PT9550SF2SS: Upper Door Parts

Replacement badge designed to restore the appliance's exterior appearance and factory look. This decorative emblem replaces a faded, scratched, or missing badge so the control panel or door presents a clean, branded finish. What it does:

• Replaces a worn, cracked, faded, or missing badge to restore original appearance
• Sits on the appliance front where the original emblem was located for accurate visual match
• Helps maintain a factory-fresh look after cosmetic damage or panel repair
• Sold as the individual decorative emblem; intended as a direct-fit cosmetic replacement

• Clean and fully dry the mounting area before installing to ensure proper adhesion and fit
• Align carefully with the original location; press firmly and evenly to secure the badge

This door liner kit replaces a damaged or worn refrigerator door interior to restore a clean, sealed surface and improve door appearance. Designed to fit the OEM mounting points for a proper fit and reliable performance. What it does:

• Replaces cracked, warped, stained or otherwise damaged door liner surfaces
• Restores a smooth interior surface to help door shelves and bins mount correctly
• Helps maintain a consistent door seal by providing a true mounting surface for gaskets and hardware
• Improves overall appearance of the refrigerator door interior

• Disconnect power to the appliance before beginning service
• Remove door shelves, bins, and any trim before removing the old liner
• Retain and reuse any existing screws, clips, or hardware unless replacements are provided in the kit

This door insulation retainer is a small plastic clip that secures insulation inside a refrigerator/freezer door to help maintain proper temperature and reduce noise. It replaces worn or missing retainers to keep the door liner insulation in place. What it does:

• Secures the door insulation to the inner door liner so insulation stays positioned
• Helps prevent insulation from shifting or sagging that can affect door seal performance
• Commonly used when insulation falls out or the liner shows gaps around the insulation
• Works as a direct-fit replacement for the original retainer designed for the door assembly

• One door insulation retainer clip

• Installation generally requires removing the door panel or liner; keep track of fasteners and trim
• Handle the door liner and insulation carefully to avoid damage or tearing the insulation
• Use proper tools and disconnect power if working near electrical components or lights
• Replace all affected clips for an even, secure fit

A replacement liner support that secures the refrigerator cabinet liner and keeps interior trim and panels aligned for a proper seal and appearance. Restores stability to cracked or broken support points. What it does:

• Holds the cabinet liner and interior trim in position to prevent gaps and movement
• Helps maintain door seal alignment by keeping liner edges stable
• Reduces rattling or shifting caused by a damaged support
• Commonly replaced when liner pieces are cracked, broken, or loose

• One liner support

• Disconnect power to the appliance before beginning any repair
• Remove food, shelves, and trim pieces as needed to access the damaged support
• This part typically secures with clips or fasteners; inspect existing hardware and replace if necessary

The Oven door gasket is an OEM part for GE wall ovens and ranges. It fits around the inner rim of the oven door, creating an essential heat and air seal when closed. 

Symptoms of a bad door gasket include: 

• Excessive heat loss around the door when preheating or cooking  
• Ghosting or condensation buildup visible on the door glass
• Worn or misshapen gasket that no longer presses firmly against the door rim

Gasket material naturally hardens over time through repeated exposure to temperature changes. Accidental damage from cleaning can also impact the gasket's integrity. Replacing it with this genuine GE part helps maintain an efficient cooking environment. 

This OEM GE replacement gasket is also compatible with some Kenmore, Hotpoint, and RCA wall oven and range models. Proper sealing is important for energy efficiency as well as consistent cooking results.
 

This handle and end cap assembly replaces a damaged or worn door handle to restore a secure grip and clean appearance. It's a direct-fit exterior part used on compatible GE refrigerator/freezer doors. What it does:

• Provides a finished grip surface for opening and closing the door
• Replaces cracked, broken, or loose handles and end caps
• Restores proper alignment and attachment where the original handle is damaged
• Improves door appearance by replacing worn or discolored components

• High-level installation; verify correct orientation and attachment hardware before starting
• Turn off and empty the door area as needed for safe access
• Use appropriate hand tools; avoid overtightening fasteners to prevent cracking

This outer door assembly provides the exterior stainless-steel panel and structure for your oven door, restoring appearance and protecting internal door components. It replaces a damaged, dented or cosmetically worn outer oven door. What it does:

• Restores the oven's exterior finish and protects inner door parts from damage
• Helps maintain proper door closure and a sealed cooking cavity when installed correctly
• Replaces dented, scratched or corroded outer door surfaces for improved appearance
• Works with the door's glass and inner components to keep the oven functioning as intended

• One outer door assembly (stainless steel)

• Disconnect power to the appliance before starting repair to avoid shock or injury
• Use two people when handling the door assembly to avoid dropping or damaging the part
• Follow OEM disassembly/reassembly steps for removing door glass and fasteners; do not overtighten screws

This handle support mount kit secures and reinforces an appliance door handle so it stays aligned and stable during normal use. It replaces worn or broken handle supports to restore proper handle fit and function. What it does:

• Provides the mounting point and hardware to secure a door or panel handle
• Stops handle wobble, looseness, or sag caused by worn supports or damaged mounts
• Restores correct handle alignment for safe, reliable operation
• Works as the replacement support when the original mounting has cracked or failed

• Disconnect power (or unplug) and remove any panels before starting
• Use basic hand tools (screwdriver/socket) and avoid over-tightening fasteners to prevent damage
• Handle replacement may require holding the handle in position while securing the support

The Door Hinge (Left) is an OEM part for GE ranges. It acts as the pivot point that allows the left side of the range door to open and close.

Causes of a bad hinge include normal wear and tear from repeated use, accidental impacts that deform the hinge, or failure of brackets or bushings.

Symptoms of a bad left door hinge include:

• Difficulty or resistance when opening and closing the left side of the door
• Noise or squeaking coming from the hinge area  
• Visual signs of damage or bending to the hinge itself
• The left side of the door not staying firmly shut or becoming misaligned

This OEM GE replacement hinge is also compatible with Hotpoint, RCA, and select Kenmore models.

The Door Hinge (Right) is an OEM part for GE ranges. It acts as the pivot point that allows the right side of the range door to open and close.

Causes of a bad hinge include normal wear and tear from repeated use, accidental impacts that deform the hinge, or failure of brackets or bushings.

Symptoms of a bad right door hinge include:

• Difficulty or resistance when opening and closing the right side of the door
• Noise or squeaking coming from the hinge area  
• Visual signs of damage or bending to the hinge itself
• The right side of the door not staying firmly shut or becoming misaligned

This OEM GE replacement hinge is also compatible with Hotpoint, RCA, and select Kenmore models.

This replacement oven door window glass restores a clear view into the oven and helps maintain proper heat containment. Replace a cracked, shattered, or clouded window panel to keep cooking safe and your appliance looking like new.

• Creates the transparent viewing window in the oven door
• Helps retain heat and maintain a proper door seal
• Direct replacement for cracked, shattered, scratched, or stained glass
• Typical symptoms: visible damage, fogging between panes, loose/rattling window, or noticeable heat loss at the door

• Disconnect power and allow the oven to cool completely
• Wear cut-resistant gloves and eye protection; handle glass carefully
• Remove the door and lay it flat on a padded surface; transfer any brackets, trim, or gasket from the original glass as required by your model
• Reassemble carefully; do not overtighten fasteners and verify the door seals and operates properly

This inner oven door window spacer positions and cushions the glass inside the oven door assembly to help maintain a secure fit and proper spacing. It supports safe, consistent sealing and helps prevent rattling or glass contact with the inner panel. What it does:

• Keeps the inner oven door glass properly spaced from the door frame and outer glass
• Cushions the glass to reduce vibration and rattling during operation
• Helps maintain an even seal to support temperature stability inside the oven
• Prevents direct glass-to-metal contact that can cause chipping or stress

• One oven door window spacer

• Designed for use inside the oven door assembly; door disassembly is usually required
• Handle glass and spacer carefully to avoid chips or cuts; use gloves and safety glasses
• Disconnect power to the appliance before starting any repair and follow OEM instructions

ST10-16 X 7/16"

Black. 8-18 AB HXW 3/8

Includes 12 washers.

This handle support mount kit secures and reinforces an appliance door handle so it stays aligned and stable during normal use. It replaces worn or broken handle supports to restore proper handle fit and function. What it does:

• Provides the mounting point and hardware to secure a door or panel handle
• Stops handle wobble, looseness, or sag caused by worn supports or damaged mounts
• Restores correct handle alignment for safe, reliable operation
• Works as the replacement support when the original mounting has cracked or failed

• Disconnect power (or unplug) and remove any panels before starting
• Use basic hand tools (screwdriver/socket) and avoid over-tightening fasteners to prevent damage
• Handle replacement may require holding the handle in position while securing the support

This 10-32 machine screw secures brackets, panels, and other hardware in cooking appliances. Replacing a missing or stripped screw restores a snug, rattle-free fit and keeps components aligned and safely fastened. What it does:

• Fastens panels, brackets, and components using a 10-32 machine thread
• Replaces hardware that is missing, rusted, or stripped
• Helps address loose or rattling parts and minor panel misalignment
• Maintains secure mounting after service or part replacement

• One 10-32 machine screw

• Disconnect power; for gas appliances, also shut off gas before service
• Support the panel or bracket while removing/installing hardware
• Start threads by hand to avoid cross-threading; do not overtighten
• Replace them one at a time to keep alignment