Parts for Ge C2S995SEL1SS: Upper Oven Parts

If your oven won't preheat or shows an F3 error code, this temperature sensor monitors oven heat and safety features. Direct plug replacement, 15-minute fix.

10-32 machine screw secures panels, brackets, door hinges, and handles in ovens and ranges. Replace missing, stripped, or broken screws for tight fit.

Replacement bumper cushion that protects the range frame where panels meet. Install when the original is worn, cracked, or missing to reduce vibration.

Slide-out oven rack assembly for electric ranges. Installs inside the oven cavity. Replace if your rack is damaged, won't slide smoothly, or missing.

Seals the inner edge of your oven door to retain heat for even cooking. Replace if you notice heat escaping or uneven temperatures. Verify fit.

Right-hand hinge assembly secures and guides your range oven door. Replace when hinge is cracked, broken, or worn to restore proper door alignment.

This dual plunger switch completes dispenser controls when the dispenser lever is pressed, restoring proper water and ice dispensing response. It replaces a worn or failed dispenser actuator switch to help the dispenser register lever movement. What it does:

• Acts as the dispenser lever switch assembly, closing circuits when the lever/plunger is depressed
• Controls water and/or ice dispense signals to the dispenser control board or valve
• Commonly linked to symptoms such as no water or ice when pressing the dispenser, intermittent dispensing, or unresponsive dispenser lever
• Helps restore reliable electrical contact for dispenser operation when the original switch is faulty

• One dual plunger switch assembly

• Disconnect power to the appliance before beginning any work
• Shut off water supply if removing water-connected components near the dispenser
• Access typically requires removing the dispenser bezel or front panel to reach the switch; handle panels and connectors gently
• Reconnect wiring exactly as removed and verify operation before reassembling all panels

Holds and powers the interior oven light bulb for visibility while cooking. Replace if light flickers, won't turn on, or bulbs burn out frequently. Verify fit by your model number before ordering.

Metal angle support bracket that secures interior panels, shelves, or trim inside your range. Replace if cracked, bent, or missing to maintain proper alignment.

Uneven cooking or excessive heat outside your oven? This rear cavity insulation restores thermal protection and improves heating efficiency. DIY-friendly.

Rear insulation panel installs behind the oven cavity to contain heat and protect components. Replace if cracked, damaged, or missing to restore insulation.

Seals between the oven light lens and liner to keep grease and moisture out. Replace if damaged, cracked, or no longer sealing properly.

Oven door won't lock during self-clean cycle? This automatic door latch assembly secures your oven door when locked operation is required. DIY repair.

Shoulder screw for ranges and ovens. Secures internal components and panels. Order a replacement if your original screw is stripped, missing, or damaged.

Oven not heating evenly or bottom not baking properly? This hidden bake element restores consistent bottom heat. Moderate DIY repair in 30-45 minutes.

Dim or dark oven interior? This lamp cover protects and diffuses your range's light bulb for clear visibility. Replaces cracked or missing lens. Easy fix.

This cover latch secures the appliance's top access cover so it stays closed during use and lets you open the cover for service or maintenance. It restores a positive, smooth-closing latch action for safe access. What it does:

• Holds the top/access cover closed to prevent accidental opening during operation
• Provides a solid engagement point for the cover to snap or latch into place
• Replaces a broken, worn or loose latch that causes rattling or an unsecured cover
• Helps ensure proper alignment of the cover for safe servicing and operation

• Disconnect power (unplug or shut off breaker) before beginning any service
• Typically installs with simple snap-in or screw fasteners; keep fasteners from the original part

Bottom oven panel for electric ranges. Replaces cracked, damaged, or missing lower oven exterior panels. Restores appearance and structure.