Parts for Ge PT9200SL2SS: Upper Oven Parts

A small rubber door bumper that cushions the contact point between the appliance door and cabinet to reduce noise, prevent chipping, and help the door close smoothly. Simple replacement restores quiet operation and protects finishes. What it does:

• Cushions the door edge to stop metal-on-metal or door-on-cabinet contact
• Helps the door sit and close more evenly to reduce misalignment symptoms
• Reduces banging, rattling, and scraping noises when the door closes
• Prevents wear and cosmetic damage at the door contact point

• Inspect the door/cabinet contact area to locate the bumper before replacing
• Most installations press the bumper into a hole or recess; use steady, even pressure to seat it
• If the old bumper is glued or fastened, remove residue and check the mounting method in your parts diagram
• Turn off power to the appliance before working near electrical components or wiring

The Oven Temperature Sensor Assembly is an OEM replacement part for GE electric wall ovens. It is responsible for accurately reading the oven's internal temperature to provide precise temperature control and safe operation. Consistent and precise temperature readings are necessary for repeatable cooking results.  

Symptoms of a bad temperature sensor include:

• Inability to reach or maintain set cooking temperatures
• Fluctuating temperatures causing inconsistent results  
• Error codes or fault messages related to temperature regulation
• Potential safety concerns if temperatures run too high or low

Causes of a faulty sensor can be due to failures over extended usage, exposure to high heat cycles, or impedance changes due to dirt or mineral deposits. Precise temperature readings allow for confident cooking.

This OEM GE replacement sensor is also compatible with Hotpoint, RCA, and some Kenmore electric wall oven models. 

This halogen lamp with a G9 base restores bright, dependable interior lighting in your appliance. Replace a burned-out or damaged bulb so you can clearly see food and monitor cooking progress without opening the door. What it does:

• Provides bright illumination inside the appliance cavity when the light is switched on or the door is opened
• Restores visibility after the original bulb fails
• Common symptoms: no light, dim or flickering light, intermittent operation, or a visibly damaged capsule
• Direct-fit G9 bi-pin base installs into the existing socket

• 1 halogen lamp (G9 base)

• Disconnect power and allow the appliance to cool completely before service
• Remove the lens/cover as directed in your model's manual
• Handle the new halogen bulb with clean gloves or a tissue—oils on skin can shorten bulb life
• Align the G9 pins and press straight into the socket; replace the cover and restore power

A replacement frame board assembly that secures the oven/range control console and gives the control area a finished appearance. Restores proper mounting and protection for the control electronics so buttons and displays sit correctly. What it does

• Provides the structural frame and mounting surface for the range/oven control console and control board.
• Protects control electronics and wiring from exposure and interference.
• Keeps front control buttons, switches and displays aligned and stable.
• Restores the unit's finished appearance when the original frame is cracked, bent or broken.

• Disconnect power to the appliance before starting work to prevent shock or damage.
• Handle sharp sheet-metal edges carefully and keep small fasteners organized for reassembly.
• Some disassembly of the backguard or control console may be required to access mounting screws.

The Control Board is an OEM part for GE ovens. As the central control unit, the control board monitors and regulates critical cooking functions such as temperature settings, timers and safety features.

Causes of a bad control board can be normal wear and tear over time, exposure to heat and moisture leading to corrosion of electronic components, or accidental damage.

Symptoms of a bad control board include:

• Unresponsive control panel or dim/missing display
• Inability to select bake or broil temperatures
• Failure to preheat or maintain proper temperatures
• Safety sensors not functioning correctly

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This oven rack is a replacement chrome wire shelf that supports cookware and bakeware inside the oven, restoring proper airflow and cooking position. It slides into the oven's rack rails and provides a stable surface for pans and trays. What it does

• Replaces a missing, bent, or damaged oven rack so cookware sits level during baking and roasting
• Restores proper rack spacing and airflow for even cooking
• Allows trays and pans to slide in and out smoothly when rack rails are intact
• Helps prevent cookware from tipping or sliding during use

• One chrome oven rack

• No tools typically required; slide rack into the oven's existing rack guides until it seats securely
• Inspect rack rails for damage or buildup and clean before installing to ensure smooth operation
• Use oven mitts or heat-resistant gloves when removing or installing racks in a hot oven
• Do not modify the rack; replace if bent or warped

This bake element assembly provides the oven's primary lower heating element for baking and roasting, restoring heat for normal cooking performance. Designed to replace a failed or visibly damaged bake element. What it does:

• Heats the oven cavity during bake cycles so food reaches set temperatures
• Replaces a burned-out or open bake element that prevents the oven from heating
• Helps correct slow heat-up, lack of heat, or uneven baking when element is the cause
• Works as the main lower heating surface for baking and roasting

• Disconnect power to the range before starting any repair; this part involves live electrical terminals
• Allow the oven to cool completely and wear gloves to protect hands from sharp edges
• Handle the element carefully to avoid bending; ensure terminals are fully seated and secured
• After installation, restore power and run a short bake cycle to confirm proper operation

This broil shield assembly protects the oven cavity and components from direct broiler heat, helping keep the oven interior functioning safely and reducing the chance of heat damage. It fits behind the broil element and routes heat away from surrounding parts. What it does:

• Shields the oven back wall and wiring from intense broiler heat
• Helps prevent heat-related discoloration, warping, and premature part wear
• Can reduce smoke caused by direct drips hitting the broil element
• Restores proper broiler airflow and shielding after damage or corrosion

• High-level replacement — remove power (unplug or turn off breaker) before servicing
• Use basic hand tools; avoid contact with sharp sheet-metal edges
• Inspect surrounding insulation and fasteners; replace any damaged clips or hardware

This is a replacement screw that can be used with many different types of household appliances. Screws fasten various pieces of machines together. They can also help to reduce the amount of vibration in the machine. If a screw is missing or damaged, it could cause a machine to stop working properly, or to vibrate more than it should.The screws are made from metal and will typically last for a long time. However, the threads and other parts of the screw can wear down with use. The screws could also become lost when making other repairs to the appliance. Replacement of the screws is generally easy, but it will depend on where it is placed.This item can replace certain screws found in various models of ranges, ovens, dryers, and microwaves from General Electric, Hotpoint, Whirlpool, and Kenmore. This is a genuine OEM replacement part sourced from the manufacturer. It is sold individually. Owners may want to have several replacements on hand in case they need them.

These GE screws are a 12-pack of OEM replacement parts responsible for securing and fastening various components and panels in a GE range or oven. These screws are designed with a hexagonal head, which allows for the use of a compatible wrench or socket for tightening. They are commonly used to attach sheet metal panels, brackets, and other parts within the appliance, ensuring that these components remain securely in place during operation.

This part fixes the following symptoms:

• Loose or wobbly parts or panels within the appliance's interior or exterior
• Panels or components falling out of place, creating gaps or exposing internal parts
• Unusual noises or rattling sounds during the appliance's operation

The GE screws can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.

This replacement screw secures appliance components and helps keep panels, brackets, and controls firmly attached for reliable operation. It's a simple, direct fix when a mounting screw is missing, loose, or stripped. What it does:

• Fastens panels, trim, brackets or electrical components to reduce movement and rattling.
• Restores proper alignment of parts that shift when a screw is missing or worn.
• Helps maintain electrical and mechanical connections by keeping components seated.
• Common symptom: loose or vibrating panels, trim gaps, or visibly missing hardware.

• Disconnect power to the appliance before accessing internal components.
• Use the correct screwdriver or driver bit to avoid stripping the head.
• Thread gently and avoid overtightening to prevent stripping the mating threads or cracking surrounding parts.
• Keep any removed hardware organized to ensure placement of all required fasteners during reassembly.

Black. 8-18 AB HXW 3/8