Parts for Ge PCB969SP2SS: 04 - Warming Drawer Parts

Replace a cracked, broken, or worn oven door handle assembly. This 30-inch handle restores secure grip and mounts to original installation points.

This flat washer (.250 inch inner diameter x .812 inch outer diameter) is a simple replacement part that helps distribute load from a fastener and protects mating surfaces for reliable appliance operation. What it does:

• Provides a stable bearing surface for screws, bolts or studs to reduce wear on parts
• Helps distribute clamping force to prevent pull-through or deformation of softer materials
• Reduces vibration and movement at the joint when installed correctly
• Missing or damaged washers can lead to loose fasteners, increased vibration or component misalignment

• Disconnect power and water before servicing the appliance
• Replace like-for-like: inner/outer diameters and thickness match the original washer
• Inspect mating hardware and surfaces for damage; replace corroded or deformed fasteners as needed
• Tighten fasteners evenly and avoid over-torquing to prevent washer or component damage

This drawer gasket forms the sealing edge for a refrigerator drawer to help maintain proper compartment temperature and reduce air exchange. It restores a tight seal so stored food stays fresher and the appliance runs efficiently. What it does:

• Replaces a worn or torn drawer seal that allows warm air into the drawer
• Helps reduce frost buildup, moisture, and premature spoilage of food
• Improves compartment temperature stability and cooling performance
• Prevents drafts and rattling caused by a loose or damaged gasket

• One drawer gasket

• Remove the drawer and old gasket, clean mounting channel before installing the new gasket
• Press gasket into the channel evenly; some designs clip or tuck into a retainer—avoid sharp tools that could damage the new seal
• If gasket is stiff, warm briefly with a hair dryer on low to ease installation; allow to cool and set before use
• For safety, unplug the appliance or switch off power before servicing

Seals your range warming or storage drawer to prevent heat loss and improve efficiency. Replace if worn, cracked, or loose. Confirm fit with your model number.

Replacement oven rack slide guide for your range. Installs inside the oven cavity to support and guide racks. Order now if cracked or broken.

Range won't heat or burners stopped working? A burnt or melted terminal block may be the cause. This wiring connection hub routes power to elements. DIY repair in 10-20 minutes.

Terminal block mount for electric ranges. Secures the terminal block connection housing. Replace if cracked, broken, or damaged. Direct fit installation.

Adjustable leveling leg for electric ranges. Installs on the bottom corner of the unit. Replace if broken, cracked, or missing to level your range.

Mounting screw secures panels, trim, and internal components in ranges and ovens. Replace if missing, stripped, or damaged to restore proper fit.

Mounting screw for oven and range assemblies. Secures internal components and panels. Replace if stripped, missing, or damaged during repairs.

This replacement mounting screw is used in cooking appliances to fasten components securely. It restores a tight, rattle-free fit so panels, brackets, or burner-related parts stay properly aligned during everyday use.

• Secures appliance components to the chassis or assembly
• Replaces a missing, stripped, or corroded screw
• Helps resolve loose panels, wobbling parts, or vibration noises
• Supports proper alignment of mounted parts

• Disconnect power at the breaker; for gas units, also shut off gas supply
• Allow the appliance to cool completely before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Tighten snugly without overtightening; replace damaged threads or hardware as needed

This is a replacement screw that can be used with many different types of household appliances. Screws fasten various pieces of machines together. They can also help to reduce the amount of vibration in the machine. If a screw is missing or damaged, it could cause a machine to stop working properly, or to vibrate more than it should.The screws are made from metal and will typically last for a long time. However, the threads and other parts of the screw can wear down with use. The screws could also become lost when making other repairs to the appliance. Replacement of the screws is generally easy, but it will depend on where it is placed.This item can replace certain screws found in various models of ranges, ovens, dryers, and microwaves from General Electric, Hotpoint, Whirlpool, and Kenmore. This is a genuine OEM replacement part sourced from the manufacturer. It is sold individually. Owners may want to have several replacements on hand in case they need them.

ST10-16 X 7/16"

8-18 AB IHW 5/8 S

Replacement screw secures panels, brackets, and trim inside your oven or range. Restores tight fit when original hardware is missing, stripped, or damaged.