Parts for Ge PHS920SF2SS: Warming Drawer Parts

This handle and end cap assembly replaces a damaged or worn door handle to restore a secure grip and clean appearance. It's a direct-fit exterior part used on compatible GE refrigerator/freezer doors. What it does:

• Provides a finished grip surface for opening and closing the door
• Replaces cracked, broken, or loose handles and end caps
• Restores proper alignment and attachment where the original handle is damaged
• Improves door appearance by replacing worn or discolored components

• High-level installation; verify correct orientation and attachment hardware before starting
• Turn off and empty the door area as needed for safe access
• Use appropriate hand tools; avoid overtightening fasteners to prevent cracking

This flat washer (.250 inch inner diameter x .812 inch outer diameter) is a simple replacement part that helps distribute load from a fastener and protects mating surfaces for reliable appliance operation. What it does:

• Provides a stable bearing surface for screws, bolts or studs to reduce wear on parts
• Helps distribute clamping force to prevent pull-through or deformation of softer materials
• Reduces vibration and movement at the joint when installed correctly
• Missing or damaged washers can lead to loose fasteners, increased vibration or component misalignment

• Disconnect power and water before servicing the appliance
• Replace like-for-like: inner/outer diameters and thickness match the original washer
• Inspect mating hardware and surfaces for damage; replace corroded or deformed fasteners as needed
• Tighten fasteners evenly and avoid over-torquing to prevent washer or component damage

This drawer gasket forms the sealing edge for a refrigerator drawer to help maintain proper compartment temperature and reduce air exchange. It restores a tight seal so stored food stays fresher and the appliance runs efficiently. What it does:

• Replaces a worn or torn drawer seal that allows warm air into the drawer
• Helps reduce frost buildup, moisture, and premature spoilage of food
• Improves compartment temperature stability and cooling performance
• Prevents drafts and rattling caused by a loose or damaged gasket

• One drawer gasket

• Remove the drawer and old gasket, clean mounting channel before installing the new gasket
• Press gasket into the channel evenly; some designs clip or tuck into a retainer—avoid sharp tools that could damage the new seal
• If gasket is stiff, warm briefly with a hair dryer on low to ease installation; allow to cool and set before use
• For safety, unplug the appliance or switch off power before servicing

Range won't heat or burners stopped working? A burnt or melted terminal block may be the cause. This wiring connection hub routes power to elements. DIY repair in 10-20 minutes.

Left hand side

Right hand side

Terminal block mount for electric ranges. Secures the terminal block connection housing. Replace if cracked, broken, or damaged. Direct fit installation.

Fix a warming drawer that won't heat with this low-temperature heating element. Restores gentle, consistent warming performance for cooked food in ranges.

Mounting screw secures panels, trim, and internal components in ranges and ovens. Replace if missing, stripped, or damaged to restore proper fit.

Replacement mounting screw for securing panels, brackets, and components inside your range or oven. Restores proper fit when original is missing or stripped.

This is a replacement screw that can be used with many different types of household appliances. Screws fasten various pieces of machines together. They can also help to reduce the amount of vibration in the machine. If a screw is missing or damaged, it could cause a machine to stop working properly, or to vibrate more than it should.The screws are made from metal and will typically last for a long time. However, the threads and other parts of the screw can wear down with use. The screws could also become lost when making other repairs to the appliance. Replacement of the screws is generally easy, but it will depend on where it is placed.This item can replace certain screws found in various models of ranges, ovens, dryers, and microwaves from General Electric, Hotpoint, Whirlpool, and Kenmore. This is a genuine OEM replacement part sourced from the manufacturer. It is sold individually. Owners may want to have several replacements on hand in case they need them.