Parts for Whirlpool LTE6234DT2: 01 - Washer / Dryer Control Panel, Literat Parts

The Timer is an OEM part for Whirlpool washers, designed to control the sequence of operations in your washing machine, from filling with water to spinning and draining. This mechanical device determines the duration of each cycle, ensuring your clothes are washed under optimal conditions for the selected settings.

Causes for timer malfunction often involve internal component wear, electrical failures, or corrosion due to moisture exposure. Over time, contacts within the timer can wear out or burn, leading to incomplete or erratic operation.  

Symptoms of a bad Timer include:

• The washer not starting or completing a cycle.
• Stuck on one part of the cycle for too long.
• Water not filling or draining correctly.
• The machine skipping certain cycles or operations.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Color: almond. Measures about 2 inches in diameter.

Color: almond. Measures about 2 inches in diameter.

Color: almond. Measures about 2 inches in diameter.

Almond

This control knob replaces a worn or broken stove/oven control knob and restores clear, safe temperature and function selection. The biscuit-colored knob matches original styling for a clean, finished look. What it does:

• Fits onto the appliance control shaft to allow manual selection of settings and temperatures.
• Replaces cracked, stripped, loose, or missing knobs that are hard to turn or won't stay set.
• Restores tactile feedback for accurate control of burners/oven functions.
• Helps prevent accidental setting changes by providing a secure grip.

• One biscuit-colored control knob.

• Remove power to the appliance before replacing controls to avoid electrical or burn hazards.
• Pull off the old knob (or lift release clip if present) and align the new knob on the splined shaft; press firmly until seated.
• If the knob feels loose or doesn't engage, don't force—check shaft condition.

White

This fixed-value resistor is an electrical component used in select dryers to limit current in a specific control circuit. It helps the timer or electronic control operate correctly by dropping voltage to safe, design-intended levels.

• Provides precise resistance to reduce voltage/current in the designated dryer circuit
• Supports proper operation of the timer, control board, or end-of-cycle signal (varies by model)
• Failure may present as a timer that won't advance, an inoperative signal/buzzer, or irregular cycle behavior
• Replace if visibly burned/damaged or if testing shows an open or shorted condition

• Disconnect power to the appliance before servicing
• Access the console/wiring harness and note original wire routing
• Make secure, insulated connections and route the resistor/leads exactly as original to avoid heat or chafing
• After installation, run a test cycle to ensure proper operation of the affected function

This is a replacement timer knob/dial for your dryer that restores a secure grip and clear selector markings. It lets you turn the timer and select drying cycles when the original knob is cracked, loose, or missing. What it does:

• Replaces a worn, broken, or missing timer knob so the timer control turns smoothly
• Provides a visible selector marker for choosing dryer cycle settings
• Prevents slipping or intermittent engagement between control shaft and knob
• Matches the biscuit (light tan) color used on many appliance control panels

• Disconnect power before servicing the appliance to avoid shock or injury
• Most knobs pull straight off the control shaft; pull firmly and evenly to remove
• If required, remove the control panel or use a screwdriver to access retaining hardware
• Do not force the new knob onto a damaged or bent shaft; inspect the control shaft for wear

Restore smooth, accurate cycle selection with this replacement timer knob for your dryer. When the original knob is cracked, stripped, or missing, this part lets you reliably set the timer and choose drying programs again. What it does:

• Attaches to the timer shaft so you can set drying cycles and time
• Replaces knobs that are cracked, stripped, loose, or missing
• Helps resolve issues like the knob spinning freely or not turning the timer
• Provides a clean, factory look in white

• 1 white timer knob

• Disconnect power to the dryer before servicing
• Pull the old knob straight off the timer shaft; use steady, even pressure if tight
• Align the new knob with the keyed shaft and press firmly until fully seated
• The pointer aligns with the control panel cycle markings before use

Restore smooth, accurate cycle selection with this replacement timer knob for your dryer. When the original knob is cracked, stripped, or missing, this part lets you reliably set the timer and choose drying programs again. What it does:

• Attaches to the timer shaft so you can set drying cycles and time
• Replaces knobs that are cracked, stripped, loose, or missing
• Helps resolve issues like the knob spinning freely or not turning the timer
• Provides a clean, factory look in white

• 1 white timer knob

• Disconnect power to the dryer before servicing
• Pull the old knob straight off the timer shaft; use steady, even pressure if tight
• Align the new knob with the keyed shaft and press firmly until fully seated
• The pointer aligns with the control panel cycle markings before use

This screw-washer assembly secures panels, brackets, and other appliance components. The integrated washer spreads load and resists loosening, so replacing a worn or missing fastener restores a tight, reliable fit and helps eliminate rattles.

• Provides fastening with a built-in washer for even clamping and retention
• Replaces missing, stripped, or corroded hardware
• Helps address loose panels/handles and vibration or rattle noises
• Supports proper alignment of covers, brackets, and trim

• Disconnect power and shut off water or gas (as applicable) before servicing
• Match to the original fastener; location and quantity in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten with the correct driver
• Do not overtighten; replace other severely rusted or damaged fasteners in the same area

This pressure switch is a replacement air-pressure sensor that helps the appliance detect proper airflow and system pressure so cycles run correctly and safety systems operate as intended. What it does

• Senses changes in air or system pressure and sends a signal to the control to advance or stop cycles
• Helps ensure proper venting and airflow for heating and drying functions
• Can cause long cycles, failure to start, lack of heat, or error codes when faulty
• Works with the appliance's vacuum hose/tubing and electrical connector to monitor pressure

• Disconnect power (and gas, if applicable) before beginning work
• Handle the vacuum hose and small fittings carefully to avoid cracks or leaks

10 - 16 x 1/2

The Start Switch is an OEM part for Whirlpool dryers. This switch is essential for initiating the drying cycle, allowing the user to start the dryer by pressing the button. It ensures the dryer begins operation and runs through the selected cycle properly. 

Causes of a bad start switch can include electrical issues such as short circuits, mechanical wear from frequent use, or damage due to moisture or impact.

Symptoms of a bad start switch include:

• The dryer not starting when the button is pressed
• Intermittent operation or the need to press the button multiple times to start the dryer
• No response or sound when the start button is engaged
• The start button feeling loose or not clicking properly

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This adjustable buzzer kit replaces a failed or noisy mini buzzer to restore audible alerts for cycles, timers and notifications. Compact design lets the appliance signal you reliably when cycles finish or need attention. What it does:

• Produces audible tones for cycle end, timers and other appliance notifications
• Replaces buzzers that are silent, intermittent, weak or emitting erratic beeps
• Helps you hear and identify completed cycles and timed alerts
• Small, mountable unit that fits behind the control panel and connects to the control board

• One adjustable buzzer kit

• Disconnect power before servicing to avoid shock risk
• Access may require removing the control panel; keep fasteners organized for reassembly
• Disconnect the buzzer wiring harness or connector before removing the old unit; connect the new buzzer the same way
• Test buzzer function with power restored before fully reassembling

The Timer is an OEM part for Whirlpool dryers. This component is crucial for controlling the various cycles of the dryer, such as drying time and heat settings. It ensures that the dryer operates according to the selected cycle, providing efficient and effective drying performance.

Causes of a bad timer can include electrical issues, worn-out internal mechanisms, or exposure to high heat over extended periods. Additionally, repeated use can lead to the degradation of the timer's components.

Symptoms of a bad timer include:

• The dryer not advancing through cycles
• The timer not keeping accurate time
• The dryer stopping mid-cycle
• Unusual noises coming from the timer mechanism

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This hinge bracket secures a refrigerator door hinge to the cabinet, restoring proper door alignment and support so the door seals and closes reliably. Designed to replace a worn, bent, or broken hinge mounting bracket. What it does:

• Provides a stable mounting point for the door hinge assembly to prevent sagging or drooping
• Restores correct door alignment to improve sealing and reduce cold air loss
• Stops excess movement or rattling at the hinge area
• Helps eliminate door-binding or uneven gaps that keep the door from closing fully

• Unplug the appliance and remove food/items from the door before starting
• Support the door while removing/installing the bracket to avoid damage or injury
• Reuse or replace fasteners as required; tighten securely but avoid over-torquing
• After installation, check door alignment and gasket seal; make minor adjustments as needed

This motor connector housing is the molded body that holds the motor's wire terminals for a secure, insulated connection. Replacing a cracked or heat-damaged housing helps restore reliable motor operation and prevent intermittent power issues.

• Organizes and insulates the motor's wiring terminals
• Locks the harness to the motor for a firm electrical connection
• Helps reduce loose contacts, arcing, and heat damage at the plug
• If the housing is failing, you may see intermittent or no motor operation, the machine stopping mid-cycle, or visible melting/discoloration at the motor connector

• Disconnect power; also shut off gas supply
• Note wire positions; transfer terminals into the new housing one at a time to maintain orientation
• Inspect terminals and wiring; replace any burnt or loose terminals before reassembly
• Ensure the connector seats fully on the motor and the harness is secure; restore power and test