Parts for Whirlpool LTE6234DZ2: 01 - Washer / Dryer Control Panel, Literat Parts

Fix a washer that won't advance to rinse cycle or stops mid-program. This timer controls wash, rinse, and spin sequences. DIY install in 5-10 minutes.

Replacement timer knob for washers. Installs on the control panel to operate the timer dial. Order if your original knob is cracked, broken, or missing.

Replacement timer knob for washers. Installs on the control panel to operate the timer dial. Order if your original knob is cracked, broken, or missing.

Replacement timer knob for washers. Installs on the control panel to operate the timer dial. Order if your original knob is cracked, broken, or missing.

Almond

Replace your washer dryer combo's worn, cracked, or missing control knob. This biscuit-colored knob installs on the control panel shaft for cycle selection.

White

This fixed-value resistor is an electrical component used in select dryers to limit current in a specific control circuit. It helps the timer or electronic control operate correctly by dropping voltage to safe, design-intended levels.

• Provides precise resistance to reduce voltage/current in the designated dryer circuit
• Supports proper operation of the timer, control board, or end-of-cycle signal (varies by model)
• Failure may present as a timer that won't advance, an inoperative signal/buzzer, or irregular cycle behavior
• Replace if visibly burned/damaged or if testing shows an open or shorted condition

• Disconnect power to the appliance before servicing
• Access the console/wiring harness and note original wire routing
• Make secure, insulated connections and route the resistor/leads exactly as original to avoid heat or chafing
• After installation, run a test cycle to ensure proper operation of the affected function

This is a replacement timer knob/dial for your dryer that restores a secure grip and clear selector markings. It lets you turn the timer and select drying cycles when the original knob is cracked, loose, or missing. What it does:

• Replaces a worn, broken, or missing timer knob so the timer control turns smoothly
• Provides a visible selector marker for choosing dryer cycle settings
• Prevents slipping or intermittent engagement between control shaft and knob
• Matches the biscuit (light tan) color used on many appliance control panels

• Disconnect power before servicing the appliance to avoid shock or injury
• Most knobs pull straight off the control shaft; pull firmly and evenly to remove
• If required, remove the control panel or use a screwdriver to access retaining hardware
• Do not force the new knob onto a damaged or bent shaft; inspect the control shaft for wear

Restore smooth, accurate cycle selection with this replacement timer knob for your dryer. When the original knob is cracked, stripped, or missing, this part lets you reliably set the timer and choose drying programs again. What it does:

• Attaches to the timer shaft so you can set drying cycles and time
• Replaces knobs that are cracked, stripped, loose, or missing
• Helps resolve issues like the knob spinning freely or not turning the timer
• Provides a clean, factory look in white

• 1 white timer knob

• Disconnect power to the dryer before servicing
• Pull the old knob straight off the timer shaft; use steady, even pressure if tight
• Align the new knob with the keyed shaft and press firmly until fully seated
• The pointer aligns with the control panel cycle markings before use

Restore smooth, accurate cycle selection with this replacement timer knob for your dryer. When the original knob is cracked, stripped, or missing, this part lets you reliably set the timer and choose drying programs again. What it does:

• Attaches to the timer shaft so you can set drying cycles and time
• Replaces knobs that are cracked, stripped, loose, or missing
• Helps resolve issues like the knob spinning freely or not turning the timer
• Provides a clean, factory look in white

• 1 white timer knob

• Disconnect power to the dryer before servicing
• Pull the old knob straight off the timer shaft; use steady, even pressure if tight
• Align the new knob with the keyed shaft and press firmly until fully seated
• The pointer aligns with the control panel cycle markings before use

This screw-washer assembly secures panels, brackets, and other appliance components. The integrated washer spreads load and resists loosening, so replacing a worn or missing fastener restores a tight, reliable fit and helps eliminate rattles.

• Provides fastening with a built-in washer for even clamping and retention
• Replaces missing, stripped, or corroded hardware
• Helps address loose panels/handles and vibration or rattle noises
• Supports proper alignment of covers, brackets, and trim

• Disconnect power and shut off water or gas (as applicable) before servicing
• Match to the original fastener; location and quantity in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten with the correct driver
• Do not overtighten; replace other severely rusted or damaged fasteners in the same area

This pressure switch is a replacement air-pressure sensor that helps the appliance detect proper airflow and system pressure so cycles run correctly and safety systems operate as intended. What it does

• Senses changes in air or system pressure and sends a signal to the control to advance or stop cycles
• Helps ensure proper venting and airflow for heating and drying functions
• Can cause long cycles, failure to start, lack of heat, or error codes when faulty
• Works with the appliance's vacuum hose/tubing and electrical connector to monitor pressure

• Disconnect power (and gas, if applicable) before beginning work
• Handle the vacuum hose and small fittings carefully to avoid cracks or leaks

10 - 16 x 1/2

Dryer won't start when you press the button? The start switch initiates the drying cycle. Simple 10-minute DIY fix with basic tools and our guide.

This adjustable buzzer kit replaces a failed or noisy mini buzzer to restore audible alerts for cycles, timers and notifications. Compact design lets the appliance signal you reliably when cycles finish or need attention. What it does:

• Produces audible tones for cycle end, timers and other appliance notifications
• Replaces buzzers that are silent, intermittent, weak or emitting erratic beeps
• Helps you hear and identify completed cycles and timed alerts
• Small, mountable unit that fits behind the control panel and connects to the control board

• One adjustable buzzer kit

• Disconnect power before servicing to avoid shock risk
• Access may require removing the control panel; keep fasteners organized for reassembly
• Disconnect the buzzer wiring harness or connector before removing the old unit; connect the new buzzer the same way
• Test buzzer function with power restored before fully reassembling

Dryer not advancing cycles or staying on continuously? A failed timer prevents proper cycle operation. DIY repair in 10-30 minutes with basic tools.

Secures the door hinge to the cabinet frame. Replace if your bracket is bent, cracked, or broken to restore proper door alignment and support.

Right-hand endcap for washer dryer combo units in biscuit color. Replaces cracked, broken, or missing side trim pieces on your appliance exterior.

Endcap for laundry center control panel. Covers the edge of the control console for a finished look. Replace if cracked, broken, or missing.

This motor connector housing is the molded body that holds the motor's wire terminals for a secure, insulated connection. Replacing a cracked or heat-damaged housing helps restore reliable motor operation and prevent intermittent power issues.

• Organizes and insulates the motor's wiring terminals
• Locks the harness to the motor for a firm electrical connection
• Helps reduce loose contacts, arcing, and heat damage at the plug
• If the housing is failing, you may see intermittent or no motor operation, the machine stopping mid-cycle, or visible melting/discoloration at the motor connector

• Disconnect power; also shut off gas supply
• Note wire positions; transfer terminals into the new housing one at a time to maintain orientation
• Inspect terminals and wiring; replace any burnt or loose terminals before reassembly
• Ensure the connector seats fully on the motor and the harness is secure; restore power and test

Secures and stabilizes the washer drum assembly. Replace if loose, rattling, or causing excessive vibration during spin cycles. Verify fit with your model.

Endcap for laundry center and washer dryer combo units. Covers and protects exposed edges or corners. Replace if cracked, broken, or missing.