White Westinghouse Range / Cooktop / Oven Trim

The Vent Trim is an OEM part for Frigidaire ranges. This part frames and supports the oven's ventilation system, ensuring proper heat dispersal and maintaining the aesthetic integration of the range within the kitchen setup.  

Common causes for vent trim issues include physical impacts during cleaning or use, thermal deformation from continuous exposure to high temperatures, and general wear and tear over time.  

Symptoms of failing Vent Trim include:

• Loose or ill-fitting trim that may not stay in place
• Visible damage such as cracks or warping due to heat exposure
• Increased heat retention or abnormal heat outside the oven
• Aesthetic discrepancies that impact the overall look of the kitchen

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This Door Trim Kit restores the finished look and proper fit around the door. It replaces damaged or missing trim that frames the door/panel, helping secure outer components and refresh the appliance's appearance.

• Provides a clean, finished edge around the door perimeter
• Helps retain/position the outer glass or panel on applicable designs
• Replaces cracked, warped, loose, or missing trim that may rattle or leave gaps
• Common symptoms: visible damage, looseness, gaps, or cosmetic wear around the door

• Disconnect power at the breaker or unplug the appliance before servicing
• Protect the work surface; wear cut-resistant gloves and handle glass carefully
• Note orientation and fastener locations; transfer any reusable clips/screws from the original assembly
• After reassembly, confirm smooth door operation and proper alignment/seal

This burner cap sits on top of the sealed burner head on a gas cooktop/range to evenly distribute flame and protect the burner from spills. Replacing a damaged or missing cap helps restore proper flame pattern and efficient cooking performance.

• Covers the burner head to shape the flame and shield it from debris
• Helps ensure even heating across cookware
• Common signs it may need replacement: uneven or yellow flames, sputtering or noisy burner, cookware scorching on one side, cap chipped, warped, or missing
• Color/finish: black

• Shut off gas supply and allow the cooktop to cool completely before servicing
• Lift off the old cap; clean the burner head surface
• Center the new cap on the burner head—ensure it seats flat and stable
• Test the burner for a steady, even blue flame after reassembly

This door trim kit restores the finished edge around the appliance door, covering raw edges and fasteners. Replace worn or missing trim to refresh the look and help keep the outer door panel properly seated. What it does:

• Finishes the perimeter of the door and conceals mounting hardware
• Helps retain and align the outer door panel or glass
• Replaces cracked, warped, loose, or missing trim pieces
• Typical symptoms include gaps around the door, loose or rattling edges, or cosmetic damage

• One door trim kit

• Disconnect power to the appliance before servicing
• Wear cut-resistant gloves; door edges and trim can be sharp
• Support or remove the door as required by your model; note screw locations and lengths
• Transfer any clips/screws from the original trim and check door alignment and operation after installation

This replacement surface burner cap sits on top of the gas burner head to focus and distribute the flame for even, efficient heating. Replacing a damaged or missing cap can restore proper ignition and flame pattern. What it does:

• Covers and protects the burner head from spills and debris
• Spreads and concentrates the flame for consistent cooking performance
• Helps prevent yellow, lifting, or uneven flames when properly seated
• Common symptoms: uneven or yellow flames, poor simmer, delayed ignition, chipped/warped/missing cap

• 1 surface burner cap

• Allow the cooktop to cool; disconnect power and shut off gas if servicing beyond simple cap replacement
• Lift off the old cap and clean the burner head surface of residue or debris
• Center the new cap on the matching burner head so it sits level—do not force
• Use the correct cap for the burner position; test ignition and flame after installation

Color: White. This is a 3-sided door trim kit.